Types from stdint.h are used in that header file without stdint.h being
included.
Change-Id: I71449dd26162dc8420c206285896ac9a8e4e04d4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The two defines are identical, so deduplicate this.
Timeless build for lenovo/x230 results in identical binary.
Change-Id: I32e0eee88d72eb6f8dc71b0324d62f46079120a9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The GLK bootblock seems(?) to be hard limited to 32KB and some Octopus
variants are so close to that that they only have 0.5KB left. This is
blocking development of new core features, so let's disable the
bootblock console to gain a couple of KB back (like we already did on
RK3288).
There are probably other opporunities for code size reduction here (e.g.
it seems that almost half(!) of that whole bootblock size is taken up by
devicetree.cb structures), but I'm not familiar enough with the platform
to dig into them.
Change-Id: I05b4ecf5abef7307e3d0a81db04a745ff3da0c42
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38521
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All variants of ga-b75m-d3h lack ACPI definitions for legacy PCI
slots, which causes IRQ issue if it gets legacy PCI card installed.
The missing definitions (mainly Interrupt Routing Table) are added to
fix that.
NOTE: The added definitions are actually for ga-b75-d3v, but since
they form superset of definitions needed by ga-b75m-d3{h,v}, they can
be applied to all three existing variants with suitable preprocessor
instructions.
Change-Id: Id79c759a5fadb38c2873edc07293cbb14401ac9a
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
BUG=b:148252157
BRANCH=none
TEST=Put a puff in s0ix, send a WoL magic packet.
Change-Id: I4a08a2f5505d00909c9301315fcf72f687141f91
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Add new mailbox command support. Set CPU ID and cores to EC.
EC will according to different CPU to set different power table.
BUG=b:148126144
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I135d2421d2106934be996a1780786f6bb0bf6b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
The System76 Lemur Pro (lemp9) is an upcoming laptop computer. Support
in coreboot is developed by System76 and provided as the default
firmware option. Testing is done on a pre-production model expected to
be identical from a firmware perspective to the production model.
Working:
- Payload
- Tianocore
- CPU
- Intel i7-10510U
- Intel i5-10210U
- EC
- ITE IT5570E running https://github.com/system76/ec
- Backlit Keyboard, with standard PS/2 keycodes and SCI hotkeys
- Battery
- Charger, using AC adapter or USB-C PD
- Suspend/resume
- Touchpad
- GPU
- Intel UHD Graphics 620
- GOP driver is recommended, VBT is provided
- eDP 14-inch 1920x1080 LCD
- HDMI video
- USB-C DisplayPort video
- Memory
- Channel 0: 8-GB on-board DDR4 Samsung K4AAG165WA-BCTD
- Channel 1: 8-GB/16-GB/32-GB DDR4 SO-DIMM
- Networking
- M.2 PCIe/CNVi WiFi/Bluetooth
- Sound
- Realtek ALC293D
- Internal speaker
- Internal microphone
- Combined headphone/microphone 3.5-mm jack
- HDMI audio
- USB-C DisplayPort audio
- Storage
- M.2 PCIe/SATA SSD-1
- M.2 PCIe/SATA SSD-2
- RTS5227S MicroSD card reader
- USB
- 1280x720 CCD camera
- USB 3.1 Gen 2 Type-C (left)
- USB 3.1 Gen 2 Type-A (left)
- USB 3.1 Gen 1 Type-A (right)
Not working:
- TPM2 - SPI bus 0, chip select 2 is used. Chip selects other than 0
are not currently supported by the intel fast_spi driver.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: Ib0a32bbc6f89a662085ab4a254676bc1fad7dc60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Under some circumstances grep detects the input of a spd hex file
as binary resulting in an spd source not beeing added to the
resulting spd.bin. This appears to be especially the case with
heavily commented files.
This commit forces grep to read the input as text file.
Example SPD that would else be detected as binary (regardless
of stripped zero blocks).
```hex
\# TotalBytes: 512 ; BytesUsed: 384
23
\# SPD Revision 1.1
11
\# DDR Ramtype: LPDDR4X
11
\# Config Rest
0E 16 21 95 08 00 00 00 00 0A 22 00 00 49 00 04
0F 92 54 05 00 84 00 90 A8 90 C0 08 60 04 00 00
[...]
\# CRC Is: 0x1EB4 Calculated: 0x1EB4 Match!
1E B4
\# ModuleSpecificParameter
[...]
\# HybridMemoryParameter
[...]
\# ExtendedFunctionParameter
[...]
\# ManufactoringInformation
\## Module Manufactoring ID
00 00
\## Module Manufactoring Location and Date
00 00 00
\## Module Manufactoring Serial
00 00 00 00
\## Module Manufactoring Part Number: "K4UBE3D4AA-MGCL"
4B 34 55 42 45 33 44 34 41 41 2D 4D 47 43 4C 00
00 00 00 00
\## Module Manufactoring Revision Code
00
\## Module Manufactor: "Samsung" (0xCE80)
CE 80
\## Module Stepping
00
\## Module Manufactoring Data
[..]
\## Module Reserved
00 00
\# EndUserProgrammable
[...]
```
Thanks to Patrick Georgi for checking that this grep option
is widely available.
Change-Id: I7e5bad069531630b36dc3702c8c4bd94ba0946c1
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38426
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the specification the register offset must be 0x71 instead
of 0x70.
Change-Id: Icf69ffc701a42a31a4545ce53c13e2c2554863e1
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Drop DRAMT write as it's only rewriting the power on default.
PMCR write is required. Update comment on its purpose and move to
end of sdram_enable().
Change-Id: I62e8b2531f0f297ffb7db440db89ffa65771b7d5
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The bits cleared by this have to do with dGPU power, which this
board lacks.
TESTED: x201 still boots.
Change-Id: I441743f76afc7bbbee930a1c8116035e85d94e52
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36911
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates SA DRAM registers bit definitions as per
SKL datasheet vol 2, doc 332688.
TEST=Build and boot EVE and Soraka to OS.
Change-Id: Ia32723444c044572fbcecce151d89e739e570b3b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
As per PC client TPM specification, the TPM description contains the
base address of the TIS interface 0xfed40000 and the size of
the MMIO area is 20KB (0x5000). Hence ACPI used to reserve those fixed
system memory from getting used by OS.
Platform with TPM_CR50 doesn't require fixed SoC mapped memory hence
additional reservation might not required.
TEST=Build and boot EVE and Soraka to OS.
Change-Id: Id02a2659ce42f705180370000df89d4f6b64afce
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38512
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Optane memory module shows up as 2 NVMe devices in x2 config - NVMe storage
device and NVMe Optane memory. Storage device uses rp9 and optane memory
uses rp11. This patch enables rp11. Please note that these two share clk pins.
This is also dependent on pciecontroller3 config to be set as 2x2 instead of
1x4 in fit configuration in IFWI.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board from Optane and check 2 NVMe devices
from lspci
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ic81244bebac78102af7ba6308ab64b18c886f839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch adds ASL methods like GRXS, GTXS, STXS and CTXS
which are used to get, set and clear gpio values. We use
ASL 2.0 syntax here for gpio.asl.
BUG=b:144680462
BRANCH=none
TEST=Build and boot tigerlake rvp board
Change-Id: I17e75ff2a7cb67e94669059a1ed9d73a720ebcb1
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38442
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIOs are divided into different communities. Each community
consists of one or more GPIO groups. We need to configure the
groups in coreboot so that they are mapped properly.
GPIO comuinities in coreboot should match with the kernel gpio
communities also. Kernel reads the ASL file from coreboot. This
patch adds the proper community mapping in ASL code to match with
kernel code. In gpio_soc_defs.c file we are indexing the groups
correctly. In gpio.h file we define all the gpio devices as kernel
populates sysfs with separate gpio device for each community. This
patch is created based on Intel Tiger Lake Processor PCH Datasheet
with Document number:575857 and Chapter number:27.
BUG=b:144680462
BRANCH=none
TEST=Build and boot tigerlake rvp board. In /sys/kernel/debug/pinctrl
verify INTC34C5:0<1-3> listing all the pins for each community.
e.g., #cat /sys/kernel/debug/pinctrl/INT34C5:00/pins should list
all the community 0 pins.
Change-Id: I40c386db060d84c1b7fba9c587f960d6a92f84ba
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Having a working board reset is certainly better when you're running
vboot (because otherwise you'll hang when transitioning into recovery
mode), but I don't think it should be strictly required, since it's
still somewhat usable without. This is particularly important for
certain test platforms that don't have a good way to reset but might
still be useful for vboot testing/prototyping.
Change-Id: Ia765f54b6e2e176e2d54478fb1e0839d8cab9849
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38417
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove fixed IccMax values for U22 CPU.
IccMax will be selected by CPU SKU.
BUG=b:148110226
BRANCH=None
TEST=build coreboot and fsp with enabled fw_debug.
Flashed to device and checked IccMax[1].
Change-Id: Ifcd31ad5b608ce599d4294a6522fdda022f8a177
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Enable both SATA ports for TGLRVP.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board with SATA memory
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I9f35682982a6c06522e58b0bbd7162ff02c37f32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38505
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure SATA FSP UPD according to mainboard design.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board with SATA memory
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I9350d71d76cd3d449fd959b5398d5ac653bc459e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38504
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch updates system agent related registers bit definitions
as per EDS.
For example:
As per CNL/ICL EDS MCHBAR register base is between bit 16-38
but coreboot programming was not aligned with EDS previously.
CNL EDS doc number: 566216
Also provide provision to program 64bit values as per SA EDS definitions
TEST=Dump MCHBAR in coreboot and ASL shows same 32 bit value.
Change-Id: I37340408fe89c94ce81953c751c8d7e22bc81a42
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1. Add a TEMP_SENSOR3
2. Update DFPS (fan performance state) table with values received
from thermal team
3. Update PL1 override to 15W
4. Update PL2 override to 51W
BRANCH=hatch
BUG=b:147792204
TEST=build and verify by thermal team
Change-Id: I21c17c09a097c963f4dd1b7d5f8212c83a639dc3
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38025
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating from commit id 2843aa62:
2019-12-12 Julius Werner 2lib: Move firmware body size reporting to
separate function
to commit id f5367d59:
2020-01-20 Joel Kitching vboot: translate recovery reason info from
vboot 2->1
This brings in 27 new commits.
Change-Id: I7d33337881fa2d36d6e562b0a390b56227cfad55
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
This CL allows MKBP events from the EC to wake the system from suspend
states.
BUG=b:144122000
BRANCH=firmware-hatch-12672.B
TEST=Verify that MKBP events generated from EC will wake the system
from S0ix.
Change-Id: I8a0d2c7ed89fa1ea937a08c3082cc5d3e782efff
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Values as per "IT8772E Preliminary Specification V0.4 (For F Version)".
Some values are unclear on this document, but is the only one I have.
Change-Id: I6d74984f453c47d6ec71963a7dcab961a22a5964
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The firmware configuration (fw_config) field is store in the CBI EEPROM
and it should be used to make firmware customization instead of
sku/variant id.
BUG=b:145519081
TEST=builds
Change-Id: I790998a29e724ecdff8876cca072267537b7cea6
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Copy ec_commands.h directly from Chromium OS EC repo at sha e57217a250.
This is needed for the FW_CONFIG CBI field definition.
Change-Id: Id010721033ebe32ac9c9482d666cf790442a26ee
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPIOs are divided into different communities. Each community
consists of one or more GPIO groups. We need to configure the
groups from coreboot so that they are mapped properly.
GPIO communities should be properly configured in GPIO_CFG and
MISCCFG registers. GPP_* defines in gpio_soc_defs.h are configured
in GPIO_CFG register while the PMC_GPP_* in pmc.h are used to
configure the MISCCFG registers.
BUG=b:144680462
BRANCH=none
TEST=Build and boot tigerlake rvp board. Verified that after
setting the gpe from devicetree the GPP_EN register for
that community gets updated setting that specific bit.
From the iotools i checked that GPE_EN register for that
community is updated with that specific bit set to 1.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I585100375feee39b5a9105bdf6d9f5ca3a5bb2fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Bill XIE