The old approach was to invalidate the entire TLB every time we set up
a table entry. This worked because we didn't turn the MMU on until
after we had set everything up. This patch uses the TLBIMVAA wrapper
to invalidate each entry as it's added/modified.
Change-Id: I27654a543a2015574d910e15d48b3d3845fdb6d1
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3166
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The "gigabit ethernet controller" (GEC) block was added to AMD
Hudson A55E to integrate ethernet capabilities into an AMD
southbridge.
The GEC is designed to work with B50610 and B50610M gigabit PHY
chips from Broadcom. These parts may not be generally available
in small quantities for embedded development.
The GEC block requires an opaque firmware blob to function. The
GEC blob is controlled by AMD and Broadcom and is not available
from coreboot.org.
This change removes GEC support from AMD Parmer and AMD Thatcher
mainboards since these boards do not have the Broadcom PHY.
AMD has requested that the GEC be hidden for Hudson FCH since
the PHY parts are not generally available. This Kconfig option
can make it appear that this is a viable and supported way to
add Ethernet to an embedded board. It is possible to use the
Hudson GEC block with other PHYs, but this requires development
of a custom GEC blob and a custom Ethernet driver. A custom GEC
blob has been developed for a Micrel PHY, but there is no
accompanying driver.
Change-Id: I7a7bf4d41e453390ecf987c9c45ef2434fc1f1a3
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3127
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
It is useful to be able to lock out certain address ranges,
NULL being the most important example.
void mmu_disable_range(unsigned long start_mb, unsigned long size_mb)
will allow us to lock out selected virtual addresses on MiB boundaries.
As in other ARM mmu functions, the addresses and quantities are in units
of MiB.
Change-Id: If516ce955ee2d12c5a409f25acbb5a4b424f699b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3160
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
It's fine to always start timer even in suspend/resume mode, so we can
move the timer_start() back to the very beginning of boot procedure.
That provides more precise boot time information.
With that timer change, the wake up state test procedure can be simplified.
Verified by building and booting firmware image on Google/Snow successfully,
and then suspend-resume without problem (suspend_stress_test).
Change-Id: I0d739650dbff4eb3a75acbbf1e4356f2569b487d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3151
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds an inline wrapper for the TLBIMVAA instruction (invalidate
unified TLB by MVA, all address space identifiers).
Change-Id: Ibcd289ecedaba8586ade26e36c177ff1fcaf91d3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3161
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The firmware media source (SPI1) is already initialized by Exynos iROM.
There is no need to do it again.
Verified by building and booting Google/Snow successfully.
Change-Id: I89390506aa825397c0d7e52ad7503f1cb808f7db
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3147
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When TIMER_QUEUE is configured on call the timer callbacks on
entry into a state but before its entry callbacks. In addition
provide a barrier to the following states so that timers are drained
before proceeding. This allows for blocking state traversal for key
components of boot.
BS_OS_RESUME
BS_WRITE_TABLES
BS_PAYLOAD_LOAD
BS_PAYLOAD_BOOT
Future functionality consists of evaluating the timer callbacks within
the device tree. One example is dev_initialize() as that seems state
seems to take 90% of the boot time. The timer callbacks could then be
ran in a more granular manner.
Change-Id: Idb549ea17c5ec38eb57b4f6f366a1c2183f4a6dd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3159
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A timer queue provides the mechanism for calling functions
in the future by way of a callback. It utilizes the MONOTONIC_TIMER
to track time through the boot. The implementation is a min-heap
for keeping track of the next-to-expire callback.
Change-Id: Ia56bab8444cd6177b051752342f53b53d5f6afc1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When the MONOTONIC_TIMER is available track the entry, run, and exit
times for each state. It should be noted that the times for states that
vector to OS or a payload do not have their times reported.
Change-Id: I6af23fe011609e0b1e019f35ee40f1fbebd59c9d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3156
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Implement the timer_monotonic_get() using the TSC.
Change-Id: I5118da6fb9bccc75d2ce012317612e0ab20a2cac
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3155
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Implement the timer_monotonic_get() functionality based off of
the local apic timer.
Change-Id: I1aa1ff64d15a3056d6abd1372be13da682c5ee2e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3154
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Haswell ULT devices have a 24MHz package-level counter. Use
this counter to provide a timer_monotonic_get() implementation.
Change-Id: Ic79843fcbfbbb6462ee5ebd12b39502307750dbb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The notion of a monotonic timer is introduced. Along with it
are helper functions and other types for comparing times. This
is just the framework where it is the responsibility of the
chipset/board to provide the implementation of timer_monotonic_get().
The reason structs are used instead of native types is to allow
for future changes to the data structure without chaning all the
call sites.
Change-Id: Ie56b9ab9dedb0da69dea86ef87ca744004eb1ae3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3152
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The notion of loading a payload in the current boot state
machine isn't actually loading the payload. The reason is
that cbfs is just walked to find the payload. The actual
loading and booting were occuring in selfboot(). Change this
balance so that loading occurs in one function and actual
booting happens in another. This allows for ample opportunity
to delay work until just before booting.
Change-Id: Ic91ed6050fc5d8bb90c8c33a44eea3b1ec84e32d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On x86 systems there is a concept of cachings the ROM. However,
the typical policy is that the boot cpu is the only one with
it enabled. In order to ensure the MTRRs are the same across cores
the rom cache needs to be disabled prior to OS resume or boot handoff.
Therefore, utilize the boot state callbacks to schedule the disabling
of the ROM cache at the ramstage exit points.
Change-Id: I4da5886d9f1cf4c6af2f09bb909f0d0f0faa4e62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3138
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The cbmem_post_handling() function was implemented by 2
chipsets in order to save memory configuration in flash. Convert
both of these chipsets to use the boot state machine callbacks
to perform the saving of the memory configuration.
Change-Id: I697e5c946281b85a71d8533437802d7913135af3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3137
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There were previously 2 functions, init_cbmem_pre_device() and
init_cbmem_post_device(), where the 2 cbmem implementations
implemented one or the other. These 2 functions are no longer
needed to be called in the boot flow once the boot state callbacks
are utilized.
Change-Id: Ida71f1187bdcc640ae600705ddb3517e1410a80d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3136
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Utilize the static boot state callback scheduling to initialize
and tear down the coverage infrastructure at the appropriate points.
The coverage initialization is performed at BS_PRE_DEVICE which is the
earliest point a callback can be called. The tear down occurs at the
2 exit points of ramstage: OS resume and payload boot.
Change-Id: Ie5ee51268e1f473f98fa517710a266e38dc01b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3135
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's helpful to provide a distinct state that affirmatively
describes that OS resume will occur. The previous code included
the check and the actual resuming in one function. Because of this
grouping one had to annotate the innards of the ACPI resume
path to perform specific actions before OS resume. By providing
a distinct state in the boot state machine the necessary actions
can be scheduled accordingly without modifying the ACPI code.
Change-Id: I8b00aacaf820cbfbb21cb851c422a143371878bd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3134
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Many of the boot state callbacks can be scheduled at compile time.
Therefore, provide a way for a compilation unit to inform the
boot state machine when its callbacks should be called. Each C
module can export the callbacks and their scheduling requirements
without changing the shared boot flow code.
Change-Id: Ibc4cea4bd5ad45b2149c2d4aa91cbea652ed93ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3133
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The boot flow currently has a fixed ordering. The ordering
is dictated by the device tree and on x86 the PCI device ordering
for when actions are performed. Many of the new machines and
configurations have dependencies that do not follow the device
ordering.
In order to be more flexible the concept of a boot state machine
is introduced. At the boundaries (entry and exit) of each state there
is opportunity to run callbacks. This ability allows one to schedule
actions to be performed without adding board-specific code to
the shared boot flow.
Change-Id: I757f406c97445f6d9b69c003bb9610b16b132aa6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3132
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
While debugging a crash it was discovered that ld was inserting
address space for sections that were empty depending on section
address boundaries. This led to the assumption breaking down that
on-disk payload (code/data bits) was contiguous with the address
space. When that assumption breaks down relocation updates change
the wrong memory. Fix this by making the rmodule.ld linker script
put all code/data bits into a payload section.
Change-Id: Ib5df7941bbd64662090136e49d15a570a1c3e041
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3149
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
STRINGIFY makes a string from a token. It is generally useful.
Even though STRINGIFY is not defined to be in the C library it's
placed in string.h because it does make a string.
Change-Id: I368e14792a90d1fdce2a3d4d7a48b5d400623160
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3144
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The "console_init" does initialize UART driver (which will setup peripheral and
pinmux) and print starting message. Duplicated initialization can be removed.
Also, console_init (from console.c) is always linked to bootblock (and will do
nothing if CONFIG_EARLY_CONSOLE is not defined) so it's safe to remove #ifdef.
Verified by building and booting on Google/Snow, with and without
CONFIG_EARLY_CONSOLE.
Change-Id: I0c6b4d4eb1a4e81af0f65bcb032978dfb945c63d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3150
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable `EARLY_CBMEM_INIT` for CBMEM console support by looking how
other boards do this.
This commit is tested by enabling the CBMEM console (`CONSOLE_CBMEM` in
Kconfig) and then in GRUB 2 (as a payload) with the cbmemc command from
the cbmemc module and in userspace with ./cbmem -c. Both worked.
Change-Id: I34618a55ded7292a411bc232eb76267eec17d91e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3142
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
The DDR3 memory initialization (with "mem_reset" set on normal boot) will cause
resume to be unstable, especially when X is running. System may show X screen
for few seconds, then crash randomly and unable to recover - although text
console may still work for a while. Probably caused by corrupted memory pages.
'mem_reset' (which refers to RESET# in DDR3 spec) should be enabled according
to DDR3 spec. But it seems that on Exynos 5, memory can be initialized without
setting mem_reset for both normal boot and resume - at least no known failure
cases are found yet. So this can be a temporary workaround.
Verified by booting a Google/Snow device with X Window and ChromeOS, entering
browser session with fancy web pages, closing LID to suspend for 5 seconds, then
re-opening to resume. Suspend/resume worked as expected.
Also tried the "suspend_stress_test" with X running and finished 100 iterations
of suspend/resume test without failure.
Change-Id: I7185b362ce8b545fe77b35a552245736c89d465e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3148
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the suspend/resume feature into bootblock and romstage.
Note, resuming with X and touchpad driver may be still unstable.
Verified by building and booting successfully on Google/Snow, and then executing
the "suspend_stress_test" in text mode ("stop ui; suspend_stress_test") in
Chromium OS, passed at least 20 iterations.
Change-Id: I65681c42eeef2736e55bb906595f42a5b1dfdf11
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3102
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move board setup procedure to snow_setup_* functions, and Snow board-specific
(wakeup) code to snow_* for better function names and comments.
Verified by successfully building and booting on Google/Snow.
Change-Id: I2942d75064135093eeb1c1da188a005fd255111d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3130
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This makes the intermediate rule visible so BL1 gets automatically
placed in the final image.
Change-Id: Iffb0268e5bbcbe135f2d39863ed64fa302409a22
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3141
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This adds $$(INTERMEDIATE) as a pre-requisite for coreboot.rom on
armv7. It is modeled after the $(obj)/coreboot.rom rule for x86.
Change-Id: I483a88035fa2288829b6e042e51ef932c8c4f23c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2095
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The "wakeup" procedure will be shared by bootblock and romstage for different
types of resume processes.
Note, this commit does not include changes in romstage/bootblock to enable
suspend/resume feature. Simply adding functions to handle suspend/resume.
Verified by successfully building and booting Google/Snow firmware image.
Change-Id: I17a256afb99f2f8b5e0eac3393cdf6959b239341
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3129
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To support suspend/resume, PHY control must be reset only on normal boot
path. So add a new param "mem_reset" to specify that.
Verified to boot successfully on Google/Snow.
Change-Id: Id49bc6c6239cf71a67ba091092dd3ebf18e83e33
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3128
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It seems that ConnectorTypeDP in DdiList supports both DP and HDMI monitors.
I tested by DP monitor and HDMI monitor connected by passive DP->HDMI adapter.
Video and audio are OK. Hot plugging is also supported.
This commit partially reverts commit >AMD Thatcher: Fix PCIE link issues< (7f23aeb0) [1].
[1] http://review.coreboot.org/3011
Change-Id: I23cf1c69a8274f47daf56f1a12aafd88bad4a128
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3088
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds support for display bring-up on Snow. It
includes framebuffer initialization and LCD enable functions.
Change-Id: I16e711c97e9d02c916824f621e2313297448732b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3116
Tested-by: build bot (Jenkins)
Add a safety check in function `intel_update_microcode` to return when
accidentally `NULL` is passed as `microcode_updates`, which would lead
to a null pointer dereference later on.
for (c = microcode_updates; m->hdrver; m = (const struct microcode *)c) {
While at it, use `return NULL` for clarity in function
`intel_microcode_find` and include the header file `stddef.h`. for it.
The review of this patch had some more discussion on adding more
comments and more detailed error messages. But this should be done in
a separate patch.
For clarity here some history, on how this was found and what caused
the discussion and confusion.
Originally when Vladimir made this improvement, selecting
`CPU_MICROCODE_IN_CBFS` in Kconfig but not having the microcode blob
`cpu_microcode_blob.bin` in CBFS resulted in a null pointer dereference
later on causing a crash.
for (c = microcode_updates; m->hdrver; m = (const struct microcode *)c) {
Vladimir fixed this by returning if `microcode_updates` is `NULL`,
that means no file is found and successfully tested this on his
Lenovo X201.
When pushing the patch to Gerrit for review, the code was rewritten
though by Aaron in commit »intel microcode: split up microcode loading
stages« (98ffb426) [1], which also returns when no file is found. So
the other parts of the code were checked and the safety check as
described above is added.
[1] http://review.coreboot.org/2778
Change-Id: I6e18fd37256910bf047061e4633a66cf29ad7b69
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2990
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
This makes sure that the product ID (PRO_ID) register can be read
when the OS kernel is figuring out what kind of CPU it's running on.
For historical reference, the original U-Boot code seems to have
worked basically by accident here. The hardware has a quirk where by
reading the value before gating the IP block keeps the value
persistent. U-Boot reads the chip ID early on to distinguish between
chip family, but we do not mix code the same way so we do not read
the chip ID. Since the value has been read before the clock gating
happens, the value remains available for the kernel to use during the
decompression stage. We don't want to rely on that behavior when using
coreboot. Instead the kernel should gate unused IPs.
(credit to Gabe for finding symptom in the kernel)
Change-Id: Iaa21e6e718b9000b5558f568020f393779fd208e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3121
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This simple error led to corrupted graphics.
How annoying.
Change-Id: I2295c0df0f1d16014a603dc5d66bd4d72f3fb7c9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3120
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Due to
$ more src/southbridge/amd/cimx/sb800/Makefile.inc
[…]
romstage-y += cfg.c
romstage-y += early.c
romstage-y += smbus.c
ramstage-y += cfg.c
ramstage-y += late.c
[…]
`src/southbridge/amd/cimx/sb800/` is passed with the switch `-I` to
the compiler, where it is also going to find the header file
`sb_cimx.h`. Therefore use `#include <sb_cimx>` everywhere, which is
what some AMD SB800 based boards already do.
The only effect is, that the compiler will not needlessly look into
directories which do not contain the header file [1].
The following command was used for the replacement.
$ git grep -l sb_cimx.h src/mainboard/ | xargs sed -i 's/#include "sb_cimx.h"/#include <sb_cimx.h>/'
[1] http://gcc.gnu.org/onlinedocs/cpp/Search-Path.html
Change-Id: I96ab34bac1524e6c38c85dfe9d99cb6ef55e6d7c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3118
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Because pointers can be 32bit or 64bit big,
using them in the coreboot table requires the
OS and the firmware to operate in the same mode
which is not always the case. Hence, use 64bit
for all pointers stored in the coreboot table.
Guess we'll have to fix this up once we port to
the first 128bit machines.
Change-Id: I46fc1dad530e5230986f7aa5740595428ede4f93
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3115
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
This PLL is unused and can be disabled to save about 250mW.
Change-Id: I1be37304d6ea5ff78696e05ad1023ce3c57f636c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3109
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The original imported code used "lcdbase" and "lcd_base" which quite
predictably caused confusion and bugs. Let's put an end to this little
bit of insanity.
Change-Id: I4f995482cfbff5f23bb296a1e6d35beccf5f8a91
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3114
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This just cleans up a few areas:
- Removed an unnecessary delay from exynos_dp_bridge_setup()
- The delay at the end of exynos_dp_bridge_init() is necessary, so
removed the comment suggesting that it might not be.
- Simplified exynos_dp_hotplug
Change-Id: I44150f5ef3958e333985440c1022b4f1544a93aa
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3113
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables clock gating to save power on unused IPs.
Change-Id: I9ab2a2535ebb91bb4110390a6f055a67146bdbf9
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3110
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch is based on >>AMD Thatcher: ConnectorTypeDP supports both DP and HDMI<< (I23cf1c6) [1]
I tested by DP monitor and HDMI monitor connected by passive DP->HDMI adapter.
Video and audio are OK. Hot plugging is also supported.
[1] http://review.coreboot.org/#/c/3088/
Change-Id: I291beff43609ecb68ece24939f2dbc7c08dd0374
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3090
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We neglected to copy xres and yres out; now we do.
Change-Id: Icc4a8eb35799d156b11274f71bcfb4a1d10e01e3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3111
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
This enables the thermal management unit (TMU) on Snow.
Change-Id: Idd76af40bf0a5408baf61ef2665fd52ae4e260ba
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3108
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This updates the Exynos TMU code for coreboot:
- Remove dependency on device tree
- Add Makefile entries
Change-Id: I55e1b624d7c7b695b1253ec55f6ae3de8dc671bc
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3107
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
David Hendricks