coreboot on skylake originally did ship with romcc bootblock and
verstage running after it. However, that configuration makes boot
flows very complicated. No platform in the current code base uses
this combination. Make VBOOT_STARTS_IN_BOOTBLOCK depend on
C_ENVIRONMENT_BOOTBLOCK.
BUG=b:78656686
Change-Id: Ia9446f209521f71c91b83d579b9e2d89744292bc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
The tablet event handler method TPET is defined as an extern, then
defined again in skylake, the only platform that supports it. In newer
versions of IASL, this generates an error, as the method is defined in
two places.
Remove the extern and the CondRefOf check. That's not needed if we
only set the EC_ENABLE_TABLET_EVENT define on platforms that have a
TPET handler.
Change-Id: I8bee069fc95637446593dfaaae1254e931421517
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
The _SB.DPTF.TPET ACPI code attached to EC_ENABLE_TABLET_EVENT doesn't
exist in the apollo lake code. Remove it from reef as part of the
cleanup to update to the new version of IASL.
This was in commit 4f803ac28f (mainboards/google/reef: Add support for
tablet mode switch.)
Change-Id: Ic10c418ddc708c1aed87ad4a9861f04d32445116
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25982
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set SPI Fast Read to 100MHz and Dual Read IO mode to speed up
the boot process by over a half second. Also, increase the Normal
Read speed to 33MHz as supported by the W25Q128FW.
BUG=b:70558952
TEST=Run cbmem -t to get boot times.
Change-Id: I616a96526ed90bb4ab0c9c6b78787799faa02633
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
The sb_set_readspeed() was touching the wrong register and
the read speed settings are handled by sb_set_spi100(). Nothing
was using the function, so remove it.
Change-Id: I23b20cf559ee759ba94d49ff6810a9baa64e86fb
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Some touchscreens need to adhere to certain timings during the power
off sequence as well as during the power on sequence. Adding
reset_off_delay_ms, enable_off_delay_ms, and stop_off_delay_ms to
accommodate these devices.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Idb4a5dbe56eee4749d2f2b514e92c28fb2c6078f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It's pretty well compressible which helps when space is tight.
The code encodes the assumption that the VBT is 8kb or less. Haven't
seen a larger one yet.
BUG=b:77971803,b:78541692
TEST=build, see that vbt.bin is compressed, boot, check log that the
reported VBT size is correct.
Change-Id: Ie25bca21d9edc408f441a292bbe2ab0459948ec4
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/25927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The SPI chip in this board needs a custom OPMENU, otherwise flashrom
fails halfway during the write.
From the default OPMENU, Block Erase (0xd8) has been replaced by AAI
write (0xad) and Fast Read (0x0b) by Write Disable (0x04).
Change-Id: Ie18ee4e32511482dab747c9ffeac60d3994df320
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/25551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The X201 coreboot image is working well on the X201i. Besides, the
X201i seems to be almost identical to the X201 except for the CPU.
Change-Id: Iecc84faf78e7de34fb1add63c20904a5a28c5e9b
Signed-off-by: Matthias Gazzari <mail@qtux.eu>
Reviewed-on: https://review.coreboot.org/25971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fix regression after commit
7f5efd9 intel/bd82x6x: Use generated ACPI PIRQ
The call to inject generated PIRQ entry was not added when
the static entries as default_irq_route.asl file was removed
from boards using intel/nehalem southbridge.
Change-Id: I8097c1ab729d1eb91a6d547ef13948c1e21eca10
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/25965
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matthias Gazzari <mail@qtux.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Changes in pin usage between yorp and bip
- LTE_OFF_ODL pin moved from GPIO_161 to GPIO_66
- I2S0 interface is not used in bip. It was used in
yorp for DMIC Wake on Voice through Nuvoton EC.
Also fix both bip and yorp pin settings for
LTE_OFF_ODL (Enable LTE and add an internal pull up).
Internal pull up can be removed later when sub-board (which
will have an external pull up for this signal) is available.
BUG=b:77869623
BRANCH=none
TEST=Build coreboot for octopus.
Change-Id: I8907bd63a43c4bc51ca991c3ec7c1cae9e39e2d1
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Move x86 specific pci_bus_default_ops into arch/x86 folder.
Fixes compilation on platforms that do neither have MMCONF_SUPPORT
nor NO_MMCONF_SUPPORT (for example: all non-x86) but select PCI.
Change-Id: I0991ab00c9a56b23cd012dd2b8b861f9737a9e9c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch fixes a bug in the software_i2c (bitbang) framework where it
would previously not return an error when receiving a NACK on a write
transaction (deviating behavior from our hardware I2C drivers). It also
adds explicit error codes to be returned for the different kinds of
failure conditions so they are more useful for debugging when dumped.
Change-Id: Ie63bf35123d89dcd99a1f9c079d4cae6a33b0b09
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Add: raw_read_cntfrq_el0() and raw_read_cntpct_el0()
Required to support Arch64 Timer
Change-Id: I86aa97039304b9e9336d0146febfe1811c9e075a
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Frequency set to 19.2 MHz
TEST=build
Change-Id: I56e57156df8a74cf629f7ada86cf5a5fcd5ad3c4
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
At the time I ported coreboot to this board, the HDMI port of my board
was broken, so I couldn't test libgfxinit on HDMI.
Change-Id: Ibb8a4ef55bd97fd2d0baacdbc72863c0985d3d76
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/25820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This change also makes sure that the sum the uma regions (TSEG, GSM,
GSM) is 4MiB aligned. This is needed to avoid cbmem_top floating between
2 usable ram region, since cbmem_top is aligned 4MiB down to easy MTRR
setup for ramstage. At least tianocore requires this and fails to boot
without it.
Better MTRR are achieved by making the memory 'hole' till 4GiB exactly
2Gib.
This code mimics how it is done in nb/intel/gm45 and achieves similar
results.
TSEG is enabled and set to 8M since this makes it easier to reuse the
common smm setup / parallel mp code and makes it possible to cache the
ramstage in there like how it's done on newer targets.
TESTED on Intel DG43GT.
Change-Id: I1b5ea04d9b7d5494a30aa7156d8c17170e77b8ad
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Programming CxDRB should be cumulative as explained in "Intel ® 4
Series Chipset Family datasheet".
This does not seem to have any real impact but better do according to
the documentation and what vendor firmware does.
This also removes some dead code.
Change-Id: I7ff3264824c843f84b9eb6c06a06aa3f151fe4b3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22911
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This training find the optimal write DQ delay and read DQS delay
settings. It does so on all lanes at the same time, like
vendor (training each lane individually has poor results).
The results are stored in the sysinfo struct and restored on next
boots and S3 resume.
This potentially increases stability as optimal settings are chosen
and is more necessary for DDR3 raminit where the write DQS delays are
leveled/variable due to the flyby topology.
TESTED on Intel DG43GT with (2G + 1G) on each channel, see that the
results are quite close to the safe original ones (that previous
worked fine) and tested with memtest86+.
Change-Id: Iacdc63b91b4705d1a80437314bfe55385ea5b6c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Remove locking of PCI device 00:00.0 registers (nehalem/finalize.c)
and remove setting the zeroth bit of the MSR_LT_LOCK_MEMORY = 0x2e7 MSR
register (model_2065x/finalize.c) to fix a frozen boot and S3 resume issue
which became apparent with commit d533b16669.
More detailed, either setting the LSB of the 32 bit register at 0x98
of the PCI device 00:00.0 (in the intel_nehalem_finalize_smm function) or
setting the LSB of the the MSR register MSR_LT_LOCK_MEMORY = 0x2e7 (in the
intel_model_2065x_finalize_smm function) indepentenly causes a freeze
during bootup or a complete session loss on resuming from S3 as described
here: https://mail.coreboot.org/pipermail/coreboot/2018-April/086564.html
It seems like Nehalem CPUs do not have a MSR_LT_LOCK_MEMORY register.
Additionally, the "Intel Core i7-600, i5-500, i5-400 and i3-300 Mobile
Processor Series, Datasheet Volume Two" indicates that registers of the
PCI device 00:00.0 cannot be locked manually. Instead, they can only be
locked by TXT, VT-d, CMD.LOCK.MEMCONFIG, ME_SM_LOCK or D_LCK.
Finally, the addresses and sizes of these registers were partially wrong.
Tested on Lenovo X201i with a Core i3 330M (no AES-NI, no VT-d and no TXT
support compared to the Core i5 and Core i7 processors of a X201).
Change-Id: I9d568d5c05807ebf7e131b3e5be8e5445476d61b
Signed-off-by: Matthias Gazzari <mail@qtux.eu>
Reviewed-on: https://review.coreboot.org/25914
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently the thermal event handler method TEVT is defined as an extern,
then defined again in platforms with thermal event handling. In newer
versions of IASL, this generates an error, as the method is defined in
two places. Simply removing the extern causes the call to it to fail on
platforms where it isn't actually defined, so add a preprocessor define
where it's implemented, and only call the method on those platforms.
Change-Id: I64dcd2918d14f75ad3c356b321250bfa9d92c8a5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Introduce bootmem custom memory tags and use them instead of reusing
LB_MEM tags.
Use asserts in bootmem_add_range to verify parameters.
Tested with uImage payload on Cavium SoC.
Change-Id: I7be8fa792fc7933ca218ecd43d250d3a9c55caa6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
* Adapt to coreboot coding style.
* Use coreboot's endian conversion functions.
* Fix header and header guards.
* Get rid of unused functions.
* Add Kconfig to build it on ramstage.
* Replace size32 with ALIGN_UP and DIV_ROUND_UP.
* Add NULL pointer checks
* Convert constants to defines
Required for Cavium's BDK and uImage FIT support.
Change-Id: I6e6cd9f78fb402bd54d684097326d26eb78d552a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Import from https://chromium.googlesource.com/chromiumos/platform/depthcharge
Required for general devicetree patching and FIT support.
Coding style and coreboot integration will be done in a separate commit.
Change-Id: Ida75d4786eae38d84bfc71bf53573dafca8eda40
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Besides the FSP codepath, Sandy Bridge has two codepaths, one native
and one in the form of a binary. This allows the use of the binary.
This can be useful to find flaws in the native raminit.
The native raminit is still selected by default.
Change-Id: I2d71fb7bc5f7b0976157be146c0e4c39a3ed5602
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
After commit 2188f57a (src/device: Update LTR configuration scheme)
coreboot will hang when reading resources on the ASMedia SATA
controller, although there is already an ASPM config override. So use
the ASPM blacklist driver instead of setting the ASPM override in the
devicetree.
Change-Id: I807d9bd4deef8c1528dff96c7646240ef75e1953
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/25819
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of `device_t` has been abandoned in ramstage.
Change-Id: I0b969a5109276d108e6140bad338c74786b967f3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: I17675b004023453f137abd387cfacd308d9b98b5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: I4b930a191130941c8349861cdd803a5be4219274
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23653
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use of `device_t` has been abandoned in ramstage.
Change-Id: I4c8acebb4a957a9600de15ea844f620a8909977b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: Ibd01659f518b7a2b1aaf334fe5b16cfb936b68b7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: Icec2e5f722c1f15493e5861b47f64698250f5813
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: I585aa48b99f4ef63905cab5d6d1502bfed0e6e42
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: Idcb8ff4081f2c45427aabb455a70fae1b46bcfc4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: Ib3e708a7fa9f0a78dc704a502a2f01ee0fe209ae
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t`has been abandoned in ramstage.
Change-Id: I2cc938958097e416b85f6592cb8a4e645a3746ed
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use of `device_t` has been abandoned in ramstage.
Change-Id: If064a4027265e8fc2ea919d9742a554abf29b8db
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Aaron Durbin