The h8s needs around 3s to respond to ps2 commands
Change-Id: I0cf01969975b8dd3839eadf90cb2dac0f1eaafc4
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16505
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
mainboard/lenovo/t60.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I4d87498637d74f96ca5809b0e810755a58fc64ab
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16405
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This creates a config for the Lenovo T60 sound card based
on values taken from vendor bios
(in /sys/class/sound/hwC0D0/init_pin_configs on linux 3.16).
The sound card configuration on the vendor bios is the same
as the one on the Lenovo x60.
It improves the default behavior of the sound card:
- internal microphone is chosen by default
- when jack is inserted it is chosen instead of internal speaker
Change-Id: I44e3eaac437fe4ad97ff2b0eb32d36b33222c09b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16529
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Replace the use of the old device_t definition inside
mainboard/lenovo/x60.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: Icaceeae2fc7276efa82d37582ecac93aaf37c41c
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16372
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Uses gpio.h instead of default_southbridge_gpio_setup to configure
southbridge GPIO's. This is more consistent with how GPIO's are
configured on newer targets.
Change-Id: I6ccd0564b929e958864739b7cde04f5592c58479
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16379
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On i945 the vram size is the default 8mb. It is also possible
to set it 1mb or 0mb hardcoding the GGC register in early_init.c
The intel documentation on i945, "Mobile Intel® 945 Express Chipset
Family datasheet june 2008" only documents those three options.
They are set using 3 bits. The documententation also makes mention
of 4mb, 16mb, 32mb, 48mb, 64mb but not how to set it.
The other non documented (straight forward) bit combinations allow
to change the VRAM size to those other states.
What this patch does is:
- add those undocumented registers with their respective vram size to
the i945 NB code;
- make this a cmos option on targets that have this northbridge.
TEST: build, flash to target, set cmos as desired and boot linux.
On Debian it can be found using "dmesg | grep stolen".
NOTE: dmesg message about reserved vram are quite different depending
on linux version
Change-Id: Ia71367ae3efb51bd64affd728407b8386e74594f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This enables the C4 low power state on the lenovo x200 and t400.
It's inspired by the thread on the mailinglist:
"[coreboot] Lenovo X200 running Coreboot drains 3-4W more power
than with Vendor BIOS".
What this does, is to enable a C3 state using MWAIT(C3) request
and set the southbridge config c4onc3_enable to automatically
upgrade C3 to the lower power C4 state.
The latency (0x37) is the same value used by the vendor bios.
With C4 enabled the idle power consumption is about ~2-3W lower.
TEST= build and install on target. Use powertop top to measure power
usage. To manually disable c-state to compare them,
do (tested on linux 4.4):
echo 1 > /sys/devices/system/cpu/cpu*/cpuidle/stateX/disable
Change-Id: I1a1663a7662ebc7157a965667680688ad6a33545
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15251
Tested-by: build bot (Jenkins)
Reviewed-by: Swift Geek
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add GPIOs initialisation before dock check.
Needed in order to properly detect the presence or absence of the lenovo
dock.
Previously the check always reported the dock as connected and currently
it always reports it as disconnected since the GPIOs are not properly
initialised during the check.
Tested and confirmed working.
Change-Id: I7fbf8c2262a1eb5dee9cbe5e23bf44f7f8181009
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16139
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
I'm not sure if that's the right fix here, but assuming the bit mask is
right, the inb is wrong.
Change-Id: I7e33019af088780a09be12513200bec63734bf97
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1229556
Reviewed-on: https://review.coreboot.org/16026
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Set max_mem_clock_mhz in devicetree to 933Mhz.
Allows to run the memory at up to DDR3-1866.
The same frequency was allowed within the first vendor bios,
but Lenovo than decided to limit it to DDR3-1333.
Tested on Lenovo T520 and DDR3-1600 DIMM (RMT3170eb86e9w16).
The RAM is now running at DDR3-1600 instead of DDR3-1333.
This gives about 4% performance increase in glmark2 using the
Intel GPU.
Change-Id: If15be497402d84a2778f0434b6381a64eda832d6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15158
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This is more of ACPI S3 resume and x86 definition than CBMEM.
Change-Id: Iffbfb2e30ab5ea0b736e5626f51c86c7452f3129
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15190
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Instead of hardcoding the PCI mmio size read it from devicetree.
Set a default value of 2048 MiB and 1024MiB for laptops without
discrete graphics.
Tested on Sandybridge Lenovo T520.
Change-Id: I791ebd6897c5ba4e2e18bd307d320568b1378a13
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/15140
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
thermal.h still has references to X230 in include guard since it
seems to have been copied from that port. Code formatting changes
in romstage.c.
Change-Id: Id8bd931bed127036e8bb4ab604d9d6145f767e56
signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/15071
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
This creates a config for the x60 audio based
on values taken from vendor bios.
The pin config is stored in (for linux 4.5 at least):
/sys/class/sound/card0/hw*/init_pin_configs
In the left column there is the pin number.
In the right column there is the default configuration of that pin.
(This has to be done while running the proprietary bios)
More information on the sound card can be found in:
/proc/asound/card0/codec#*
This also hold the information of /sys/class/sound/
What is improved:
- internal microphone is chosen by default
- when jack is inserted it is chosen instead of internal speaker
Before this had to be done manually in alsa or pulseaudio.
TEST= check if internal microphone is used by default in
pavucontrol if you are using pulseaudio.
Plug in a jack with headphones and check if there
is sound output through these and not the build-in
speaker.
Change-Id: Id3b700fd84905a72cc1f69e7d8bfa6145f231756
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/15063
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The way dispatcher table is set up prevents linker from
optimizing unused code away, we currently have raminit in ramstage.
Optimize this manually by configuring AGESA_ENTRY booleans for
romstage and ramstage separately. This will remove references in
FuncParamsInfo and DispatchTable -arrays.
All boards now include multi-core dispatcher, it has minimal footprint:
AGESA_ENTRY_LATE_RUN_AP_TASK
ACPI S3 support depends on HAVE_ACPI_RESUME being enabled:
AGESA_ENTRY_INIT_RESUME
AGESA_ENTRY_INIT_LATE_RESTORE
AGESA_ENTRY_INIT_S3SAVE
Disabled for all boards as it was not used:
AGESA_ENTRY_INIT_GENERAL_SERVICES
Change-Id: I7ec36a5819a8e526cbeb87b04dce4227a1689285
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14417
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Setting the size of the preallocated memory for the igd is done
using a cmos parameter, gfx_uma_size. This was limited to a subset of
all available sizes, that were already implemented elsewhere
in the northbridge code.
What this does is change the cmos parameter to 4 bits instead
of 3 bits to accomodate all vram sizes.
It also adds a sane default of 32mb that already was in place.
The northbridge code that reads this cmos parameter is
also changed for this new cmos settings.
352M is disabled since it causes issues on systems with 4GB or more ram.
TEST: Build, flash target. Clear cmos by corrupting
the checksum (nvramtool -c something).
Set a desired value in gfx_uma_size using nvramtool.
"dmesg | grep stolen" to see what is actually allocated.
Change-Id: Ia6479d03f1abe6d0c94bd7264365505e8f8eaeec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14900
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The included file does not declare pm_ioread(), and the
modified file does not call it either.
Change-Id: I9723caf1062db23b4a3648e07c2dc4c02f862619
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14968
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
These files do not use definitions from OptionsIds.h. Also those
definitions are required and already included for Ids.h.
Change-Id: I149fcfe2ad72fe3d7390ee2043a86432aeae3f08
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14980
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The eSATA port of Lenovo T420 is port 3. I've checked it on an iGPU
model and a dGPU model.
Change-Id: I64bcc887140c1634dd1475d29e97780a5128d0be
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/14632
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Enable the PEG device in devicetree to expose the
device if any. This is already default behaviour
for T5xx series.
Change-Id: I16bd253ca96c4cdaad8a829f6490cec9e2599b5f
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14448
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Add a universal hybrid graphics driver compatible with
all supported lenovo devices.
Hybrid graphics allows to connect the display panel to
either of one GPUs.
As there are only two GPUs one GPIO needs to be toggled.
In case the discrete GPU is activated the panel is routed to it.
On deactivation the panel is routed to the integrated
GPU.
On lenovo laptops the dGPU is always connected to PEG10 and it is
save to disable the PEG slot on dGPU deactivation.
Use common gpio.c for southbridge I82801IX.
Tested on Lenovo T520 using Nvidia NVS 5200m.
Removed Lenovo T430s from the list of supported devices,
as the T430s only supports "muxless Optimus".
Depends on change id:
Iccc6d254bafb927b6470704cec7c9dd7528e2c68
Ibb54c03fd83a529d1ceccfb2c33190e7d42224d8
I8bd981c4696c174152cf41caefa6c083650d283a
Iaf0c2f941f2625a5547f9cba79da1b173da6f295
I994114734fa931926c34ed04305cddfbeb429b62
Change-Id: I9b80b31a7749bdf893ed3b772a6505c9f29a56d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12896
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
This reverts commit 59597ead1f.
Will be replaced by lenovo common hybrid driver.
Change-Id: I994114734fa931926c34ed04305cddfbeb429b62
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12895
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
File buildOpts.c is a can of worms, pull platform memory
configuration in to OemCustomize.c. This array should be
assigned at runtime instead of linking a modified defaults
table.
Change-Id: I73d9d3fbc165e6c10472e105576d7c40820eaa6a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are other things besides PCIe port configuration that
require board specific hooks.
Change-Id: I0923651487b9ed5f6f7569ce08e02d993fa5f976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The ME hangs, the lspci shows no memory and the linux kernel
tries to request irq 0 twice. After suspend-resume the linux
kernel warns about double used irq.
genirq: Flags mismatch irq 0. 00000080 (mei_me) vs. 00015a00 (timer)
mei_me 0000:00:16.0: request_threaded_irq failed: irq = 0.
dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -16
PM: Device 0000:00:16.0 failed to resume async: error -16
Change-Id: I56ef66388e58dddcfb858294ba274621c55fbef6
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/14309
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reorder drivers to fit src/drivers/[X]/[Y]/ scheme to make
them pluggable.
Also, fix up the following driver subdirectories by switching
to the src/drivers/[X]/[Y]/ scheme as these are hard requirements
for the main change:
* drivers/intel
* drivers/pc80
* drivers/dec
Change-Id: I455d3089a317181d5b99bf658df759ec728a5f6b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14047
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This is based on t420s. Tested on a T420 without discrete GPU.
There is no support for nvidia gpu and optimus.
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: Iru Cai <mytbk920423@gmail.com>
Change-Id: Ie9405966e56180ac1c43a3c5b83181ee500177c8
Reviewed-on: https://review.coreboot.org/11765
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
power_on_after_fail=Enable in cmos.default leads to wake on AC behaviour
on mobile systems. Therefore set cmos.default entry to "Disable" in order
to improve user experience.
Change-Id: I977a4e6bc028c8c4c7fc1c2f5fdd74a59e951c60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/13884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Set MMCONF_BASE_ADDRESS to 0xf8000000.
It was already done for some boards, but not all.
The sandybridge chipset code assumes 64 pci buses behind MMCONF.
Therefore, only 64MiB of physical address space is required.
Increasing the address allows to use additional 128MiB of MMIO
space and to use the Intel IGD and a PEG at the same time.
Previously it wasn't possible to use both at the same time,
as two 256MiB areas won't fit into MMIO space.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
* Onboard GPU Intel IvyBridge Desktop
* PEG GPU AMD RV770
Change-Id: I3bf72439056c8089ada6899bb0605e5cd9d89cd6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14096
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Fix for the T4xx and T5xx series.
It does not apply to X2xx/X6x series as those have only
one GPU, which is always connected to the display.
The T6x series needs special care not handled with this patch.
Without ONBOARD_VGA_IS_PRIMARY the onboard GPU would be
deactivated in case a dedicated GPU is found and active,
leaving the system without a working display.
Change-Id: I94d1700e9afb75de83a4f2ed1ff53ba3b0559ae1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14031
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Sandy and Ivy Bridge processors use the same socket, and a mainboard
with the socket can support both types of CPUs. However, they use
different native graphics init code for LVDS and cause a crash if
running the wrong code.
This change detects the CPU type and then selects the right code to
run. It will add some more code in ramstage. It also merges the
{SANDY,IVY}BRIDGE_LVDS symbol to one SANDYBRIDGE_IVYBRIDGE_LVDS.
Tested on a Lenovo T520 with i7-2630qm and i7-3720qm
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Change-Id: I4624759f9c92d56d547db1ab4b9a1d611a182a91
Reviewed-on: https://review.coreboot.org/12087
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Tested-by: build bot (Jenkins)
Use shared gpio code from common folder.
Bd82x6x's gpio.c and gpio.h is used by other southbridges
as well and will be removed once it is unused.
Change-Id: I8bd981c4696c174152cf41caefa6c083650d283a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13614
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
In the same time remove few native gfx options which were improperly set
and only added dead code to the binary.
Change-Id: I4ed3fec03a1655ae0a779c3aa3845de273cb12e1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13649
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
This is needed for stout EC init.
Change-Id: I5c73499c17763229840152a473a2d820802ee2f6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13535
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The ThinkPad X220i is essentially identical to the ThinkPad X220 but it
has a Sandybridge i3 (instead of a Sandybridge i5/i7) CPU and the
VGA_BIOS_ID differs. Thus, support is added by using the X220 mainboard
directory and setting the VGA_BIOS_ID in Kconfig.
Change-Id: I33345a099c617e8c87a1de64b7254b7e7716ca90
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-on: https://review.coreboot.org/13594
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
