The patch makes these changes:
1) Remove the BUID swap list from ht_wrapper.c and put it in each of 15
romstage.c files where it is used (AMD family 10h projects).
2) Add a prototype to amdfam10.h.
3) Modify the swap list and test in real hardware for mahogany_fam10 and
kino family 10h and confirm HT3 operation for the SB link.
Abuild tested.
Signed-off-by: Scott Duplichan <sc...@notabs.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6439 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is to make sure that the file exists when it is needed. While this isn't the case for every C source file, it doesn't hurt either to create the file a bit sooner than strictly necessary.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6438 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
nvramtool couldn't handle certain combinations of sources for CMOS
layout and CMOS data. This change allows for nearly all combinations.
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6437 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The cmos.default code wasn't actually used so far, due to an oversight
when forward-porting this feature from an old branch.
- Extend walkcbfs' use by factoring out the stage handling into C code.
- New sanitize_cmos() function that looks if CMOS data is invalid and
cmos.default exists and if so overwrites CMOS with cmos.default data.
- Use sanitize_cmos() in both bootblock implementations.
- Drop the need to reboot after writing CMOS: CMOS wasn't used so far,
so we can go on without a reboot.
- Remove the restriction that cmos.default only works on CAR boards.
- Always build in cmos.default support on boards that
USE_OPTION_TABLE.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6436 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6435 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6434 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
States for AMA3000BEX5AR, SDA3100AIO3BX, and SDA3400AIO3BX
are from AMD document 30430 3.51. States for ADA3200AIO4BX
derived from SSDT of a MS-7135. States for TMDML34BKX5LD derived
from legacy PowerNow! table of a MS-7135, and therefore lack accurate
TDP information.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6432 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6431 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
With this change the last P-state entry of the last CPU in the table
is successfully conveyed into the SSDT.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6430 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i is a leftover from debugging, no longer needed. So just remove it.
Signed-off-by: Sylvain "ythier" Hitier <sylvain.hitier@gmail.com>
Acked-by: Sven Schnelle <svens@stackframe.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6424 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6423 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
lex.yy.c_shipped wasn't committed in r6420, which breaks the build
if you don't have the expert option checked that rebuilds those files.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6422 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
all boards to the new config scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Allow user to add 'subsystemid <vendor> <device> [inherit]' to devicetree.cb for
PCI and PCI domain devices.
Example:
device pci 00.0 on
subsystemid dead beef
end
If the user wants to have this ID inherited to all subdevices/functions,
he can add 'inherit', like in the following example:
device pci 00.0 on
subsystemid dead beef inherit
end
If the user don't want to inherit a Subsystem for a single device, he can
specify 'subsystemid 0 0' on this particular device.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6420 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6419 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6418 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6417 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6416 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6415 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6414 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6413 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I don't understand what this was doing nor find docs for these regs
Maybe it was left over from some copy & paste ?
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6411 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I don't understand what this was doing nor find docs for these regs
Maybe it was left over from some copy & paste ?
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6410 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I don't understand what this was doing nor find docs for these regs
Maybe it was left over from some copy & paste ?
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6409 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
In fact I changed coreDelay before deleting
the code in fidvid that called it. But there're
still a couple of calls from src/northbridge/amd/amdmct/wrappers/mcti_d.c
Since the comment encouraged fixing something, I
parametrized it with the delay time in microseconds
and paranoically tried to avoid an overflow at pathological
moments.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6408 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
bits 13 - 15 of F3xd4 (StutterScrubEn, CacheFlushImmOnAllHalt and MTC1eEn
are reserved for revisions D0 and earlier, so whe should not set them
to 0 in fidvid.c config_clk_power_ctrl_reg0(...), called from prep_fid_change.
For revisions > D0 (when we support them) it is ok not ot clear them,
because they are documented as 0 on reset. bit 12 should be left alone
according to BKDG. Should I set 11:8 ClkRampHystSel to 0 in the mask
too, just to indicate we're touching them ? We'll OR them to 1111 anyway...
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6407 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Well, I understand it better like this, but maybe
it's only me, part of the changes are paranoic, and
the only effective change is for a factor depending on
mobile or not that I can't test.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6406 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add an untested step in BKDG 2.4.2.8. I don't
have the hardware with Core Performance Boost and
I think it's only available in revision E that does
not even have a constant yet.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6405 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add to init_fidvid_stage2 some step
mentioned in BKDG 2.4.2.7 that was missing . Some lines
are dead code now, but may handy if one day we support
revison E CPUs.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6404 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add to init_fidvid_stage2 some step for my CPU (rev C3)
mentioned in BKDG 2.4.2.6 (5) that was missing
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6403 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Looking at BKDG the process for updating
Pstate Nb vid after warn reset seemed
more similar to the codethat was there fo
pvi than the one for svi, so I called the
pvi function passing a pvi/svi flag. I don't
find documentation on why should UpdateSinglePlaneNbVid()
be called in PVI, but since I can't test it,
I leave it as it was.
This patch showed some progress beyond fidvid in my
boar,d but only sometimes, most times it just didn't
work.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6402 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Factor out some common expressions.
Add an error message when coreboots hangs waiting for a pstate
that never comes (it happened to me), and throw some
paranoia at it for good mesure.
If I understood BKDG fam10 CPUs never need a software initiated vid transition,
because the hardware knows what to do when you just request
a Pstate change if the cpu is properly configured. In fact
unifying a little what PVI and SVI do was better for my board (SVI).
So I drop transitionVid, which I didn't understand either (why
did it have a case for PVI if it is never called for PVI ?
Why did the PVI case distinguigh cpu or nb when PVI is
theoretically single voltage plane ? ).
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6401 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
actual SIO. This fixes the serial device being disabled during PNP
init.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6400 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Contemplate the possibility of nbCofVidUpdate not being
defined, trying to get closer to BKDG
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6399 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Configuration of F3x[84:80] was hardcoded for rev B.
I change that for some code that checks for revision
and configures according to BKDG. Unfinished but
hopefully better than it was.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6398 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
BKDG says nbSynPtrAdj may also be 6 sometimes.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6397 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I didn't understand quite why it did that iwth F3xA0 (Power
Control Misc Register) so I moved Pll Lock time to rules in defaults.h
and reimplemented F3xA0 programming. A later patch will remove
a part I don't know what's mean to do.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Bring F3xD4 (Clock/Power Control Register 0) more in line
with BKDG i more cases. It requires looking at the CPU package type
so I add a function for that (in the wrong place?) and some
new constants
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6395 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . Factor out the decision whether
to update northbridge frequency and voltage because there
was the same code in 3 places and so we can later modify it
in one place.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode).
No change of behaviour intended.
Refactor FAM10 fidvid . Factor out the decision whether
to update northbridge frequency and voltage because there
was the same code in 3 places and so we can later modify it
in one place.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6393 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Sven Schnelle