We set T3 as 300ms to meet Elan's spec, but the resume/suspend times
are greater than 500ms, which is the spec for Chromebooks.
The actual kernel timing has been measured, and given the ACPI delay
after deasserting reset in addition to the delay until the kernel
driver accesses the device, delaying only 200ms in the ACPI method is
also sufficient to meet the 300ms requirement.
BUG=b:210772498
BRANCH=none
TEST=build and test touchscreen function on DUT.
TEST=suspend, wake DUT and check touchscreen function.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4bb4eda09686cb59b6e19c741aa2b78d84332d2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch provides the possible options for PCH to allow `Pad
Configuration Lock`.
`SOC_INTEL_COMMON_BLOCK_GPIO_LOCK_USING_SBI` config is for Tiger Lake
Point (TGP) and Alder Lake Point (ADP) PCH.
BUG=b:211573253, b:211950520
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I7cf35893ab613b154a1073060081a09e561ffe56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch introduces a `const bit_mask` variable to hold the gpio
PAD mask value prior to sending the lock configuration command using
the sideband interface.
Additionally, this patch fixes the PAD lock overridden issue as below:
Without this code change every consecutive PAD lock operation resets
other bits in that register as below:
After Locking pad 2 , pcr_read=0x4
After Locking pad 3 , pcr_read=0x8
After Locking pad 4 , pcr_read=0x10
After Locking pad 5 , pcr_read=0x20
After Locking pad 6 , pcr_read=0x40
After Locking pad 7 , pcr_read=0x80
After Locking pad 8 , pcr_read=0x100
With this code change all previous lock bits are getting preserved as
below:
After Locking pad 2 , pcr_read=0x4
After Locking pad 3 , pcr_read=0xc
After Locking pad 4 , pcr_read=0x1c
After Locking pad 5 , pcr_read=0x3c
After Locking pad 6 , pcr_read=0x7c
After Locking pad 7 , pcr_read=0xfc
After Locking pad 8 , pcr_read=0x1fc
BUG=b:211573253, b:211950520
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I342a666aa2d34bcc8ba33460396d1248f0c0f89f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60999
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ADL-P 2+8+2 (28W) would have a match PD to ADL-P 4+8+2 (28W). Group them
into the same group core "ADL_P_282_482_28W_CORE".
BUG=b:211365920
TEST=Build and check fsp log to confirm the settings are set properly.
Signed-off-by: Curtis Chen <curtis.chen@intel.com>
Change-Id: I3f92c0f5d717dd33ac478fbaa883f3e972e7a7de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Camera LED blinks as sensor is being probed during kernel boot,
which misleads user to belive camera has been turned on.
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:214155527
TEST=Build and boot Kano to OS. Verify entries in SSDT and monitor LED
during boot.
Signed-off-by: Jim Lai <jim.lai@intel.com>
Change-Id: I92f1e88d0fcce49660a95d4402c8c4161e320168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61109
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:210501484
BRANCH=puff
TEST=build
Change-Id: I84bc378d6b00828366309be7dbf56a61702a14da
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
This will make the method available earlier. This is needed for the next
CL.
BUG=b:213828947
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iee911a2debcfbf4309d2e866401b74f2a6c18feb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The only option to make HECI1 function disable on Elkhart Lake SoC
platform is using SBI under SMM mode.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I76c625e6221fdef1343599e7dbc7739caa91bf98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng Lean Tan <sheng.tan@9elements.com>
The only option to make HECI1 function disable on Ice Lake SoC
platform is using SBI under SMM mode. Hence, this patch makes
DISABLE_HECI1_AT_PRE_BOOT=y default and selects
`HECI_DISABLE_USING_SMM` config for Ice Lake.
Also, drop `HeciEnabled` from chip configuration and guard
heci_disable() using DISABLE_HECI1_AT_PRE_BOOT config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: If4155e5c7eeb019f7dce59acd5b82720baddcb43
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This implementation is the same for all SoC that select
SOC_AMD_COMMON_BLOCK_NONCAR, so factor it out to the common AMD non-CAR
CPU support code folder.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I53528f0bb75e9d945740ad5065c75e7de7b5878f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61257
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will verify that signed verstage binaries and the bootblock code
executing agree on the transfer buffer struct size.
BUG=b:213828947
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I597e38fe0a37416ffd3bc01fd974fa8f6610a88c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
MEMORY_SOLDERDOWN puts SPD in cbfs and read part number from CBI.
MEMORY_SODIMM puts SPD cache in FMAP.
BUG=b:208910227
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idab48293fb5b584ecb4c8f270d2c376456954553
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Create the banshee variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:214871796
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_BANSHEE
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ib4f943a109f945204a9b0a8de9b99580bf01c87e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
llvm-ar does not support "open" script command, and fails with an error.
This patch fixes it by removing lines `$(AR) rc <object-files>` and
it puts them as "addmod" commands. This way all object files and
archives can be packed into one archive.
Change-Id: I0c53d1d613b5edc321e268d1d996fac3146680f8
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
set_cpu_type(): It determines the CPU type (big or small) that
is executing the function, and marks the global_cpu_type's array slot
which is corresponds to the executing CPU's index if the CPU type is
big core.
get_cpu_index(): It determines the index from LAPIC Ids. This is
required to expose CPPC3 package in ascending order of CPUs' LAPIC ids.
So, the function returns CPU's position from the ascending order list
of LAPIC ids.
TEST=Tested CPU index calculation, core type determination on Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: If4ceb24d9bb1e808750bf618c29b2b9ea6d4191b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add file gpio.c in romstage.
BUG=b:213828931
TEST=Build FW and system can power on normally.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ie868fe7ada9deb8918d6c7ba538332cbe539ee44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch implements a SoC overrides to check CPU privilege level
as the MSR is not consistent across platforms.
For example: On APL/GLK/DNV, it's MSR 0x120 and CNL onwards it's MSR
0x151.
BUG=b:211573253, b:211950520
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I515f0a3548bc5d6250e30f963d46f28f3c1b90b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch creates a `relative increment by 1` macro to let SoC
gpio pad configuration to be more flexible while adding support
for newer PCH SoC.
With this changes adding GPIO controller support for PCH-N would
become really simple without too much of code duplication.
For example: ADL-N has added `GPP_I` pins into community 1 hence,
the additional code for `PCH-N` whould appear incremetal to ADL-P.
> #define GPP_B 0x0
> #define GPP_T INC(GPP_B)
> #define GPP_A INC(GPP_T)
> #define GPP_R INC(GPP_A)
> #define GPD INC(GPP_R)
> #define GPP_S INC(GPD)
> if CONFIG(SOC_INTEL_ALDERLAKE_PCH_N)
> #define GPP_I INC(GPP_S)
> #define GPP_H INC(GPP_I)
> #else
> #define GPP_H INC(GPP_S)
> #endif
> #define GPP_D INC(GPP_H)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie3b2183381b877da0a6e5a27f5176f0e21e0c9fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Present the Semtech SX9360 SAR sensor that protects the LTE antenna.
The sensor is connected to i2c bus I2C1.
BUG=b:194318328
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: I9feef9d132c60738bafb22ceb7d3468c798fab9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59609
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add driver for setting up Semtech sx9360 SAR sensor.
The driver is based on sx9310.c. The core of the driver is the same, but
the bindings are slightly different.
Registers are documented in the kernel tree:
Documentation/devicetree/bindings/iio/proximity/semtech,sx9360.yaml
[https://patchwork.kernel.org/project/linux-iio/patch/20211213024057.3824985-4-gwendal@chromium.org/]
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Change-Id: I0a912f184e6f3501f894cca24c0d71a2c3087516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This adds the following commits:
* 22ce1b5 cezanne: Upgrade SMU to 64.60.0
* dd37ad2 cezanne: Update ABL to 0x1B096070
* 01fbf5d cezanne: Update SMU to 64.58.0
* f638765 cezanne: Update ABLs to 0x1A296070
BUG=none
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8f51cb007ce4127428b7b81095fb2c7afb33e608
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Enable S3/S0ix wake events for AC connect/disconnect on Alder Lake RVP.
BUG=None
BRANCH=None
TEST=Verify board wakes from S0ix on AC connect/disconnect.
Change-Id: Iaf92821fd69a59624e58cb8af3896e2b6998723f
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Add eMMC device into chipset.cb and keep it `off` by default.
eMMC device is applicable only for Alder Lake N SOC.
Change-Id: I2bc38ee5814688409feb7e4531c1daa5b54953c0
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
EC_IN_RW signal from EC GPIO is connected to GPIO E7 of SOC. This GPIO
can be used to check EC status trusted (LOW: in RO) or untrusted (HIGH:
in RW).
BRANCH=None
BUG=None
TEST=Issue manual recovery and confirm DUT is entering recovery mode.
Change-Id: Ib8b6be9fcda24bd2bb479b5b6c01f24a6e9c7b1f
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
The patch moves the CPPC_PACKAGE_NAME macro definition from file
acpi/acpigen.c to include/acpi/acpigen.h file since the
CPPC_PACKAGE_NAME method will get called from cpu/intel/common
in a later patch.
TEST=Built the code for Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ic547445cdbe2b1a3efe44390bd127f577386e7fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The latest schematics changes the TPM I2C from I2C3 to I2C1. This patch
turns on I2C1 and turns off I2C3.
BUG=b:211886429
TEST=Test if proto 1 can boot into Chrome OS successfully.
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I0e94c900b48adf10880aae2abb47e08d1bd9e19b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Host device id 0x4619 is missed in few coreboot tables so that
coreboot can't recognize and config it properly.
Document Number: 690222
BUG🅱️214665785, b:214680767
Change-Id: I95908bdc0a736bafedb328dda2a00b5473de3d88
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
That vendor firmware still works after applying `me_cleaner` doesn't
mean that coreboot will also work with the same broken ME firmware.
Instead, one should first test coreboot with the original, unmodified ME
firmware to make sure coreboot works properly, and only then consider
using `me_cleaner` with coreboot. Otherwise, one would end up with a
non-booting or otherwise misbehaving system when trying to use coreboot
and `me_cleaner` without having tested coreboot with the original ME
firmware beforehand, which is hard to diagnose as the problem may only
happen when the ME isn't running normally.
Change-Id: I1626d747a99969faf7db37c10cf7d87e3977744a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Updating from commit id 4c21b57eb:
2021-07-19 11:36:07 +0000 - (pd: Fix missing polarity_rm_dts in some conditions)
to commit id e486b388a:
2022-01-12 21:11:11 +0000 - (zephyr: Update power policy for API change)
This brings in 2212 new commits.
Signed-off-by: zhixingma <zhixing.ma@intel.com>
Change-Id: I4437f09c3193ec7c89f7f9550940a0fa5464a511
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Thejaswani Putta <theja427@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
In https://crrev.com/c/3069716, the samus EC firmware was removed from
the `main` branch, therefore in order to update the `chromeec` 3rdparty
submodule, the automatic build and inclusion of samus EC firmware into
coreboot's `master` branch has to be dropped as well.
Change-Id: I6fcdd3b7925b6ec33ba48892ed750c29bb60634c
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Turns out 150ms isn't enough in the worst reset conditions. On guybrush
the TPM is reset in S0i3 and the CR50 is allowed to hibernate. The CR50
is woken up and initialized early during S0i3 resume. Occasionally the
CR50 isn't ready before the probe times out.
BUG=b:213828947
BRANCH=None
TEST=suspend_stress_test -c 1000
Change-Id: Ifda438080cf1ad2796c7061223a6a97b8e6e9987
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Keith Short <keithshort@chromium.org>
FSP 2.3 specification introduces following changes:
1. FSP_INFO_HEADER changes
Updated SpecVersion from 0x22 to 0x23
Updated HeaderRevision from 5 to 6
Added ExtendedImageRevision
FSP_INFO_HEADER length changed to 0x50
2. Added FSP_NON_VOLATILE_STORAGE_HOB2
Following changes are implemented in the patch to support FSP 2.3:
- Add Kconfig option
- Update FSP build binary version info based on ExtendedImageRevision
field in header
- New NV HOB related changes will be pushed as part of another patch
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: Ica1bd004286c785aa8a431f39d8efc69982874c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Along with commit f94405219c (soc/intel/alderlake: Hook up FSP-S CPU
PCIe UPDs), we need to set cpu pcie rp flags in devicetree now.
This CL is to add proper cpu pcie flags (PCIE_RP_LTR and PCIE_RP_AER) in
all intel projects or system will be blocked at PKGC2R with root port
LTR not enable.
BUG=b:214009181
TEST=Build and DUT (Kano) can enter deeper PKGC state normally.
Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com>
Change-Id: I0d8721bf1454448b7fc14655f0e4513001469a18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Some SKUs of google/taeko4es have a Bayhub LV2 card reader chip,
therefore enable the corresponding driver for the mainboard.
BUG=b:204343849
TEST=Build FW and checking SD card reader register is correct.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I3d2ea3db9df38e7b0cac4c32e1fca579ff43e5bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
When using the default initial core display clock frequency (648MHz),
Jasper Lake board might have a rare stability issue where the startup
of Chrome OS in secure mode may hang during re-initializing display in
kernel graphic driver.
Bugzzy didn't show this problem so far, but Intel recommends slowing
the initial core display clock frequency down to 172.8 MHz to prevent
this potential problem.
Depend on CL: https://review.coreboot.org/c/coreboot/+/60009
The CdClock=0xff is set in dedede baseboard, and we overwrite it as 0x0
(172.8 MHz) for bugzzy.
BUG=None
BRANCH=dedede
TEST=Build firmware and check the DUTs can boot up in secure mode well.
Change-Id: I592b2d7c814881074bd2fef9906f2450326c1fcd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This patch makes DISABLE_HECI1_AT_PRE_BOOT=y default for Cannon Lake
and ensures disable_heci1() is guarded against this config.
Also, makes dt CSE PCI device `on` by default.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Idd57d2713fe83de5fb93e399734414ca99977d0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This reverts commit bcd7873ea8.
Reason for revert: It makes beadrix can't boot to os without depthcharge change. The depthcharge change related with fw_config and will effect other variants.
================ error log ================
...
Starting depthcharge on Beadrix...
src/vboot/util/flag.c:50 flag_install(): Gpio already set up for flag 5.
===========================================
BUG=b:204882915
BRANCH=None
TEST=Build and boot into OS.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Id5e76fc78a56d30caf9f805a8a430f176a653bbe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60849
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds memory part used by variant beadrix to
mem_part_used.txt and generates DRAM ID allocated to the part.
BUG=b:204882915, b:210123929
BRANCH=None
TEST=Run part_id_gen to generate SPD id
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Ibff150bb4e742f32641da661cfca6594d18c52e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60242
Reviewed-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Scott Chao