GPT timer init is no longer needed after DRAM blob is switching to ARM
arch timer.
BUG=b:229800119
TEST=boot to kernel
Change-Id: Iec1f93c96e791220feed4225959ef15c074ba577
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77388
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on "MediaTek_EFUSE_MT8188_Confidential A_Technical Doc.docx",
MT8188G used in ChromeOS project does not support clock hardware
monitor. Thus, we can simplify the initialization flow by removing the
hardware default value check.
BUG=b:292866009
TEST=emerge-geralt coreboot
BRANCH=none
Change-Id: I07cd753f153da5b0aea1518a04a818214f986aeb
Signed-off-by: Sen Chu <sen.chu@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77334
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Use ARM architectual timer by initializing frequency to 13 MHz. Since
system timer is the source of the architectual timer, we also call
`timer_prepare` in `init_timer`.
BUG=b:229800119
TEST=run `suite:faft_bios` to verify the firmware stability.
check timestamps by cbmem.
Cq-Depend: chromium:4747539
Change-Id: I8b1348044e4c92984510604b7f61611e13284d86
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76919
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Per the suggestion in CB:76218, print actual values to the error
messages, which may be helpful for debugging.
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Id3a7a8c76b6ad15e7cf71225d8529f3e034935ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76442
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The AW37503 is designed to supply positive/negative supply for driving
the MIPI panel. It doesn't integrate non-volatile memory(EEPROM), so we
need to program the registers at boot. We program the target
positive/negative output voltage via I2C and enable the power rails by
pulling up ENP and ENN pins.
On Starmie, we need +/-6V power supply for the MIPI panel. We program
the AW37503 registers in coreboot so that kernel can control AW37503
via fixed regulators without additional settings(what we did for
TPS65132). Since we distinguish AW37503 and TPS65132 by reading the
vendor ID, we need to initialize I2C bus as early as possible.
Therefore, we move mtk_i2c_bus_init() to mainboard_init().
BUG=b:289482828
TEST=emerge-staryu coreboot chromeos-bootimage
TEST=Test the sequence the voltage
Change-Id: I9ccd4db19c93a032226f006eab0427f78f7b6dc8
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76219
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No matter what DRAM calibration is performed, DRAM scramble should be
enabled as long as MEDIATEK_DRAM_SCRAMBLE is set to y. Currently, DRAM
scramble is enabled only if full calibration is performed. Correct the
behavior by adding DRAMC_CONFIG_SCRAMBLE to the header config in fast
calibration flow.
BUG=b:285474337
TEST=Check the scramble feature is disabled on serial build
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: I907bccd4e68e040179e1971db6bf7a57b88dec1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75818
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the default MEDIATEK_DRAM_SCRAMBLE value overridable by adding a
prompt string.
BUG=b:285474337
TEST=build pass and check scramble feature is disabled on serial build
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: I703ac9aa3ccc4dd9d0fef9949c6b0d49449971a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75815
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The original clock rate 416MHz is insufficient for 4K resolution and
causing the screen to glitch. Set the clock rate to 594MHz to support
4K resolution.
BUG=b:236328487
TEST=Glitching screen was fixed after applying this patch
Change-Id: Ic40dd28264d03ef7218ff4edd8d4182e0fe74ea3
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75661
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Geralt SoC does not support 'persist certain regions' across reboots.
Considering the impact of missing ramoops for debugging, set
MEDIATEK_DRAM_SCRAMBLE to default n to disable this feature in
production FW image.
BUG=b:269049451,b:278478563
TEST=emerge-geralt coreboot and confirm CONFIG_MEDIATEK_DRAM_SCRAMBLE=n
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Change-Id: I109634d811a928e3e6f7f56e706a5b61a52a21ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75562
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix a typo in an enum type name, "PIM2_MI" -> "SPIM2_MI".
TEST=emerge-cherry coreboot
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Change-Id: Ib43a044dc69a93ad1dcaa5e65c66a82046a40777
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Based on the power sequence of the panel [1], the power on T2 sequence
VSP to VSN should be larger than 1ms, and the power off T2 sequence VSP
to VSN should be larger than 0ms. We modify the power sequence to meet
the datasheet requirement.
[1] B5 TV110C9M-LL0 Product Specification Rev.P0
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I4ccb5be04062a0516f84a054ff3f40afbf5279be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
The TPS65132S is designed to supply positive/negative driven
application. It communicates through standard I2C compatible interface,
and it intergrates a EEPROM whose contents will be loaded into the
register at startup. Since TPS65132S is used in staryu and geralt
projects, we move the implementation to mediatek/common.
The datasheet: TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:282902297
TEST=boot starmie to firmware screen
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Iad2c9bdea5824455efcef18b44876111061cfa1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75488
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To provide power to MIPI panel STA_HIMAX83102_J02, add support for
regulator VIO18.
BUG=b:272425116
TEST=test firmware display pass for STA_HIMAX83102_J02 on Starmie.
Change-Id: I3c3aa105e648b87fc39f881d762002f67b4422b5
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74341
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Create a new GPIO driving info table that contains only the pins used
in the bootblock. The GPIO driving info table is downsized from 1480
bytes to 24 bytes.
BUG=b:270911452
TEST=build pass
Change-Id: I24775ba93cd74ae401747c2f5a26bbf1c8f6ac0a
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74062
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Original lastbus configuration consumes constant memory size by
allocating 16 and 8 members arrays and the utilization is bad. Refactor
the lastbus structs to save memory usage.
BRANCH=none
BUG=none
TEST=bootblock.raw.bin size is reduced from 60328 bytes to 59048 bytes.
Change-Id: I07ff9ff7c75f03219e1792b92b62814293ef43fe
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74061
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently on power key long press, PMIC will be reset. It would cause
an unwanted reset pulse in the power-off sequence. To match expected
sequence, change PMIC behavior to "force shutdown".
BUG=b:271771606
TEST=long-pressing power key doesn't trigger PMIC_AP_RST_L pulse
BRANCH=corsola
Change-Id: I9ab35d82e57f43bac99fa8bd7bb69fcf52250311
Signed-off-by: Sen Chu <sen.chu@mediatek.corp-partner.google.com>
Signed-off-by: jason-ch chen <jason-ch.chen@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73705
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Currently on power key long press, PMIC will be reset. It would cause
an unwanted reset pulse in the power-off sequence. To match expected
sequence, change PMIC behavior to "force shutdown".
BUG=b:271771606
TEST=long-pressing power key doesn't trigger PMIC_AP_RST_L pulse
Change-Id: I1626892fd582dfab8fe1c1ede1da00549bc97142
Signed-off-by: Sen Chu <sen.chu@mediatek.corp-partner.google.com>
Signed-off-by: jason-ch chen <jason-ch.chen@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73704
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Lastbus is a bus debug tool. When the bus hangs, the bus transmission
information before resetting will be recorded.
The watchdog cannot clear it and it will be printed out for bus hanging
analysis.
There are two versions for lastbus:
Version 1 for MT8186, and version 2 for MT8188.
BUG=b:263753374
TEST=build pass.
Change-Id: Ibaf510481d1941376bd8da0168ef17c99a0fb9a2
Signed-off-by: ot_zhenguo.li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Signed-off-by: jason-ch chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73624
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Add a config "USE_MAX98390" to enable MAX98390 support.
MAX98390 is an I2S smart amplifier used in Geralt. It is also the
default speaker for Geralt reference board.
BUG=b:250459803
BRANCH=none
TEST=Verify beep function through CLI in depthcharge successfully.
Change-Id: I814f440cc5ac2a13404d01fb3baafeec092b1e74
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Signed-off-by: jason-ch chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73412
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Bus protection is a HW mechanism to avoid bus hang and incomplete bus
transactions. Bus protection HW must be enabled while the receiver of
the transaction is not able to respond.
BUG=b:264204465
TEST=build pass
Change-Id: I14aa63c4934073a14552cef64f40657d0197bbe1
Signed-off-by: garmin chang <garmin.chang@mediatek.corp-partner.google.com>
Signed-off-by: jason-ch chen <jason-ch.chen@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73375
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The DRAM scramble feature enhances DRAM data protection. When it's
enabled, the written DRAM data will be scrambled and hence can prevent
the data from being hacked.
This feature would make debugging more difficult (for example ramoops
would be lost after reset). Therefore, add a new config to allow
enabling or disabling the feature from coreboot, without having to
maintain two versions of the DRAM calibration blob.
BUG=b:269049451
TEST=build pass and check scramble enable or disable successfully
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: Ib4279bc1cc960fae9c9f5da39f4448a5627288d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
In the current Kconfig option MEDIATEK_BLOB_FAST_INIT, the meaning of
"BLOB" is unclear. Add "DRAM" to the name.
BUG=b:204226005
TEST=./util/abuild/abuild -t GOOGLE_STEELIX -x
Change-Id: Ida7bda770f1d1a40cae205b08c8cb22f2329e49f
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73155
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current clock register definition is wrong, which results in wrong
audio sampling rate. Fix it by adjusting the POSTDIV registers of
APLL1-APLL5.
TEST=build pass
BUG=b:250459803, b:250464574
Change-Id: I7a627169593f41906856777d738c6b13ff72d5a0
Signed-off-by: Johnson Wang <johnson.wang@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73134
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
MT8188 supports port0/port1 download. The hardware needs a trapping pin
to select the port to use. When port1 is selected, the phy of port1 will
be switched to port0. That is, port1 connector will be the physical line
of port0. Since port0 phy isn't initialized in coreboot, switch back to
port1 phy.
BUG=b:269059211
TEST=can detect USB2 devices in depthcharge.
Change-Id: Ic97d0bd9d0233883196b2e73ac2a22cd8ea9466b
Signed-off-by: Shaocheng Wang <shaocheng.wang@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
For Geralt, we use BOE_TV110C9M_LL0 as MIPI firmware display, so add the
power-on sequence for BOE_TV110C9M_LL0.
BUG=b:244208960
TEST=test firmware display pass for BOE_TV110C9M_LL0 on Geralt.
Change-Id: I3ef0b2e26d8cc0dc35c2985363ee4c3557dac8a9
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Liju-Clr Chen <liju-clr.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72749
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
The regulator MT6359P is needed by both firmware display and SD card.
To avoid duplicate initialization in ramstage, publicize init_pmif_arb()
as mt6359p_init_pmif_arb() and call it from mainboard_init(). This would
save 13 ms for boot time on Geralt.
BUG=b:244208960
TEST=test firmware display pass for BOE_TV110C9M_LL0 on Geralt.
Change-Id: I29498d186ba5665ae20e84985174fc10f8d4accd
Signed-off-by: Liju-Clr Chen <liju-clr.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72839
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
To provide power to MIPI panel BOE_TV110C9M_LL0, add support for
regulator VM18.
BUG=b:244208960
TEST=test firmware display pass for BOE_TV110C9M_LL0 on Geralt.
Change-Id: Ib8c3b2df1157b23b37492b1e9b1716903ea67799
Signed-off-by: Sen Chu <sen.chu@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72747
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
USB1_DRV_VBUS is used to provide 5V power for USB on MT8188 EVB and it's
not used on Geralt. Therefore, remove the GPIO setting of USB1_DRV_VBUS.
TEST=read usb data successfully.
BUG=b:236331724
Change-Id: Iffea7b288c83c81648d4c7ca30d2f0961f9853ff
Signed-off-by: Liju-Clr Chen <liju-clr.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72641
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that multiple platforms are trying to initialize eMMC in coreboot
instead of depthcharge, lets move common functionality into commonlib
instead of copying the same functionality between multiple platforms.
Note for consistency, changed name of set_early_mmc_wake_status() to
mmc_set_early_wake_status(). Also adding an mmc_send_cmd1() function
for retrieving the Operating Conditions Register (OCR) contents.
BUG=b:218406702
BRANCH=None
TEST=emerge-herobrine coreboot chromeos-bootimage
flash onto villager device and make sure still boots ChromeOS
Change-Id: Id00535b05bbd379081712601ef10e762c1831747
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
TCPA usually refers to log described by TPM 1.2 specification.
Change-Id: I896bd94f18b34d6c4b280f58b011d704df3d4022
Ticket: https://ticket.coreboot.org/issues/423
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When the watchdog timer reaches 0, the timer value won't reset to the
default value unless there is an external reset or a kick. It will
result in the watchdog failing to trigger the reset signal.
We kick the watchdog to reset the timer to the default value. Also,
because WDT hardware needs about 94us to synchronize the registers,
add a 100us delay before triggering the reset signal.
BUG=b:264003005, b:264017048
BRANCH=corsola
TEST= Reboot successfully with the following cmd
stop daisydog
sleep 60 > /dev/watchdog&
Signed-off-by: Runyang Chen <runyang.chen@mediatek.corp-partner.google.com>
Signed-off-by: Kuan-Hsun Cheng <allen-kh.cheng@mediatek.com>
Change-Id: Ic4964103d54910c4a1e675b59c362e93c2213b19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71754
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add DEVAPC_DEBUG option and set this option to disabled by default.
This option prevents DEVAPC log flooding during the boot process. Enable
this option when we need to debug DEVAPC issues.
TEST=DEVAPC log is disabled by default.
Change-Id: I26bc0378b8a766c6a8cc4903d64a921c3e96b93f
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71158
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
dapc_init flow is the same on MT8186, MT8188 and MT8195. So move this
function to common/devapc.c
TEST=emerge-corsola coreboot; emerge-cherry coreboot;
emerge-geralt coreboot
TEST=devapc log is shown as expected and the system boots to kernel
Change-Id: I979c3a3721a82d40c9e2db7fbe62e14a9bbd53d8
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71137
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
There are eDP and MIPI panels supported in geralt. We put the panels'
specified functions - `power_on()` and `configure_panel_backlight()` in
panel_geralt.c. Also provide the common interface `get_active_panel()`
in panel.c to generalize the display initialization. Since each board
may support a different set of MIPI panels, we put the MIPI data in a
separate file panel_geralt.c.
BUG=b:244208960
TEST=emerge-geralt coreboot
Change-Id: Ie928759e020a916f29f0364201a3cf202dc512c3
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
