There are in total three USB ports that are used on mc_ehl1:
- Port 1: Type A connector connected to USB2/USB3 port 0
- Port 2: Type A connector connected to USB2/USB3 port 1
- Onboard: connected to USB2 port 2
None of the ports supports overcurrent reporting.
Adjust the appropriate UPDs in devicetree to match the hardware
configuration.
Change-Id: I220637b8e9f03efccacd0955e82cfc0c7a6f53ee
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56454
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since mc_ehl1 does not have a display attached nor have a display
connector available (pure headless design), remove display related
settings from the devicetree.
Change-Id: Id31c09fcfba15f55eed19134bd0c2fb887bd2478
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56453
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without this configuration, even though there is no SD card it shows as
SD card is present and host controller waits for card to respond.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board with SD card and
without SD card, make sure if SD card not present then host controller
should not wait for card to respond.
Change-Id: I5dc5ba10c98d606d98e7d4f4c41c3e4f45e94452
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
The common gpio driver can be re-used for SC7180,
thus remove the existing gpio driver support and
also clean up the common macro definitions.
Add GPIO pin details specific to SC7180 chipset
for the consumers to be able to request for the
gpio functionality as per their requirement.
TEST=Validated on qualcomm sc7180 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ifd206e6bc9a549706e7a2c4bde0b7d5527ca6268
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
This enables the MCAX checking and BERT entry generation for Cezanne.
TEST=When printing all registers of all MCAX banks of core 0 on a
google/guybrush device, the registers have values that look correctly
and there is no general protection fault, so all MCAX MSRs that could be
accessed exist on Cezanne.
BUG=b:192997706
Change-Id: Ibe8047ce5bb5e7136a8786693bcced4d2225b1fd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56345
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Move M2_SSD_PLN_L to GPP_D3 for power loss notify function.
2. Set GPP_E21 as NC to remove LCLW_DET function
BUG=b:190643562
Signed-off-by: Ariel Fang <ariel_fang@wistron.corp-partner.google.com>
Change-Id: Id3c60adeb5d35c79a1c700937f93a80ad3587c5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56420
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable RSA and SHA for cezanne since support has been added to the PSP.
Also picasso and cezanne have different enums definitions for
hash algorithm, so split that out into chipset.c.
BUG=b:187906425
TEST=boot guybrush, check cbmem -t and the logs
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I725b0cac801ac0429f362a83aa58a8b9de158550
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This allows keeping track of how long it takes to load the microcode.
BUG=b:179699789
TEST=Boot guybrush
112:started reading uCode 990,448 (10,615)
113:finished reading uCode 991,722 (1,274)
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I86b67cf9d17786a380e90130a8fe424734e64657
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Use the gpio offset macro instead of a constant value.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Ia9e4b9ca7216092665f0a06ce467da01963c2364
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Program unused Cnvi BT UART GPIOs as NC since we are using
Bluetooth over USB mode for Brya.
Change-Id: I33a37ceb8a91603d2a193de5bdd1b6885eb3c319
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55317
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the taeko variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:193685558
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_TAEKO
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: If738849bc3103c52a4c4d8a8aaef3f90a62ad5c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56385
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add SPD support to gimble for LPDDR4 memory part MT53E1G32D2NP-046 WT:A and K4U6E3S4AA-MGCR.
BUG=b:191574298
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I4bfc18fd42c6ff2675e6f836c2ecc9617fac3aff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56329
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Take Kconfig switch PCI_ALLOW_BUS_MASTER into account and set the PCI
bus master bit for legacy devices only if it is allowed.
Change-Id: I7798a767d528419bb093f301140ab68cc8b9c5ae
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This patch adds support for variant specific soc chip config update
function.
Change-Id: Ic3a3ae0b409433e6dfa102c5e7a6322d4f78f730
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch makes Ampton EC wake up AP from s0ix when the state of
charge drops to 2%.
Demonstrated as follows:
1. Boot Ampton.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 2.
4. System resumes.
BUG=b:189540432
BRANCH=Octopus
TEST=Verified on Ampton.
Change-Id: I98d8e6ea185e8782ad675d4668678b341ca5d350
Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56341
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dependency file, generated by
$(HOSTCC) ... -MMD -MT $@ -c $< -o $@.orig
is determined by replacing the suffix of "$@.orig" with ".d", resulting
in "$@.d" (which is *.o.d). The file name was accidentally changed in
CB:55360. Now explicitly specify the path by the "-MF" option.
BUG=none
TEST=make unit-tests; find build/tests/ -name "*.d"
BRANCH=none
Change-Id: I01f77ebaaae78dd9e69394a49e524f1013857195
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
This change adds mem_parts_uesd.txt that contains the new
memory parts used by primus and Makefile.inc generated by
gen_part_id.go using mem_parts_used.txt.
BUG=b:193813079
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I6aa37114f3a164a4f3c35dfc9b43e1106b825bff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
As part of GPIO driver cleanup across qcom chipsets,
GPIO_OUTPUT_ENABLE has been renamed to GPIO_OUTPUT.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I51eedc722a91c5ea8e009fb8468a60667d374b49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Defining a macro for the gpio offset instead of a constant value.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Change-Id: Iefdde8f8331cf1df2e88a2c8915aefb4fa091d65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
For new MT8195 devices we will control mt6360 via EC,
so we have to add ec function of controlling MT6360 and
add CONFIG to separate them.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ic2228f5b45173f0905ea66a3a1f00ec820e0f855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
This patch sets the optimized FIVR configs for ehlcrb customized
based on the performance measurements to achieve the better power
savings in sleep states.
- Enable the external V1p05, Vnn, VnnSx rails in S0i3, S3, S4, S5
states.
- Update the supported voltage states.
- Update max supported current, voltage transition time and RFI
spread spectrum.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I1e30ff6d84bfe078fcce0f968fce6aaab7fd575b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55981
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With the new definition of mt6360_regulator_id,
merge the MT6360 LDO and PMIC interfaces into one.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7ccc32cb0a9481d5f55349c152267a44fe09d20a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
On MT8195 platforms with BC1.2, we have to use EC to control
MT6360 so the mt6360_regulator_id is redefined to match the
numbers defined in EC driver.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I9437edb9776442759ce04c31d315c3760078ffb3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56434
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No reason to use the preprocessor for this.
BUG=none
TEST=build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I920dfa2d27c2eb27e8bc50c615ccd13601610fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
These methods are oprom specific. Move them out of CBFS. I also deleted
the tohex methods and replaced them with snprintf.
BUG=b:179699789
TEST=Boot guybrush and see oprom still loads
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I03791f19c93fabfe62d9ecd4f9b4fad0e6a6146e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
New version of kconfig requires trailing slash at the end of
KCONFIG_SPLITCONFIG to indicate that it is a directory path.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I1a11eca21c4aa5a6260006c4ba2cb419eca8a802
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
As per the EDS revision 1.3 add support for I2C6 and I2C7.
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Id918d55e48b91993af9de8381995917aef55edc9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55996
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the variants can have different memory move the SPD related
content to the variant directory.
Change-Id: I38aa5e7514437bfcc61c38d64f0ba6f19350810d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56036
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If we don't escape the $ then the actual $(obj) path will be written
into the .config file. With this change `$(obj)` is written into the
.config file. The Makefile then does:
PSP_VERSTAGE_FILE=$(call strip_quotes,$(CONFIG_PSP_VERSTAGE_FILE))
Since this is a recursive assignment the $(obj) will be expanded at that
point.
This change makes it easier to compare full .config files.
BUG=none
TEST=Build ezkinil
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic961df148d3f22585f3441d75c3f2454329c678a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This change allows preloading the payload.
BUG=b:179699789
TEST=Boot guybrush and see payload read/decompress drop by 20 ms. We
now spend 7ms decompression from RAM. By switching to LZ4 we drop that
to 500us.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3ec78e628f24f2ba0c9fcf2a9e3bde64687eec44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
FILO allows to configure a line to autoboot. Hook this up into
coreboot’s build system.
TEST=Configure coreboot for QEMU i440fx with FILO as payload and
configure:
CONFIG_FILO_MASTER=y
CONFIG_FILO_USE_AUTOBOOT=y
CONFIG_FILO_AUTOBOOT_FILE="hda1:/vmlinuz root=/dev/sda1 console=tty0 console=ttyS0,115200 initrd=hda1:/initrd.img"
CONFIG_FILO_AUTOBOOT_DELAY=5
Boot Debian image with:
qemu-system-x86_64 -bios /dev/shm/coreboot/build/coreboot.rom -L /dev/shm -enable-kvm -smp cpus=2 -m 1G -hda /dev/shm/debian-32.img -serial stdio -net nic -net user,hostfwd=tcp::22222-:22
Change-Id: Id167e9a144bf466da87469108002672b299b702a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This method will allow the SoC code to start loading the payload before
it is required.
BUG=b:177909625
TEST=Boot guybrush and see read/decompress drop by 23 ms.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifa8f30a0f4f931ece803c2e8e022e4d33d3fe581
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This CL adds a method that can start the processes of reading the APOB
from SPI. It does require more RAM in ramstage since we no longer mmap
the buffer in the happy path. This will allow us to reduce our
boot time by ~10ms. The SoC code will need to be updated to call
start_apob_cache_read at a point where it makes sense.
BUG=b:179699789
TEST=With this and the patches above I can see a 10 ms reduction in
boot time on guybrush.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I930d58b76eb4558bc4f48ed928c4d6538fefb1e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56232
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will cause a linker error if these methods are used outside
ramstage.
BUG=b:179699789
TEST=compile guybrush w/ and w/o COOP_MULTITASKING
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If9983fca939c8a15fa570481bfe016a388458830
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56352
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Werner Zeh