The EC temperature sensors were renumbered and now PECI
is at index 0.
1) boot on falco
2) check /sys/class/thermal/thermal_zone0/temp
3) check 'temps' on ec console
Change-Id: Idde1457c42c80850b5b8ac22781060ed9b224d13
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61896
Reviewed-on: http://review.coreboot.org/4367
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The drivers are designed to work with an edge triggered interrupt.
Change-Id: I35a121ecfb6409bb9049f4d1e034185bb3bb7557
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61664
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4360
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Make use of google_chromeec_get_board_version to determine board
version, and apply proper RAM_ID table to load correct SPD.
Change-Id: I6a2d54759cf2ce98bf53df0db396c6e09368c714
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61192
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4353
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Update peppy's verb tables for the Realtek ALC283 Audio Codec.
ALC283 Configuration:
Digital Mic - NID 12h: Disabled
Speakers - NID 14h: Enabled
Mono out - NID 17h: Disabled
Mic 1 - NID 18h: Disabled
Mic 2 - NID 19h: Headphone Jack
Line1 - NID 1Ah: Internal Mic
Line2 - NID 1Bh: Disabled
PCBEEP - NID 1Dh: Enabled
SPDIF - NID 1Eh: Disabled
HP-OUT - NID 21h: Headphone Jack
Mic 1 doesn't seem to really be available, but the documentation
refers to NID 18h as MIC1, so it's being disabled as it's not
being used. The onboard microphone has been moved to line 1.
I had my peppy modified to attach the mic to line1 and mic1 now
works with this patch. Mic2 looks harder to rework, so I think
that will have to wait for the DVT boards.
Change-Id: I7d6ce6b428806b6aed1d36e7e25302fa5ae14b21
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/58880
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4352
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
- Update RAM_ID table.
- Add DEVSLP0 signal to NGFF SATA port.
Note: After this change, old Micron 2GB boards will no longer boot.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: Id68a1d6ace2702cca9c37305726cd55a0bde5005
Reviewed-on: https://gerrit.chromium.org/gerrit/60167
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4340
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Limit power to 12W at 73C and remove limit at 68C.
To have the CPU consume maximum power it is necessary to stress
both the CPU and the GPU. Bastion (chrome.supergiantgames.com)
and/or webglsamples.googlecode.com can be useful for this.
Testing this properly requires a script to report the running
average power readings. The watch_power.sh script is attached
to this issue in the partner tracker.
1) Run watch_power.sh continuously:
localhost ~ # watch -n 0 bash -e /tmp/watch_power.sh
2) Start Bastion (or other stress apps). The power draw should
be close to 15W if under enough load.
3) Watch until temperature climbs above 73C and is caught by
the thermal zone 10 second poll, this can be sped up by blocking
or removing the fan.
4) The ACPI thermal zone states should change to reflect that
active[2] is now enabled and power consumption should drop to 12W.
5) Stop the stress apps and wait until the CPU cools off again,
enable the fan again if it was removed.
6) The ACPI thermal zone state should switch back to active[3].
Change-Id: Ie6714a8543d4f06edf8513086fc9c968273bdb23
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60545
Reviewed-on: http://review.coreboot.org/4335
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Don't force dev mode. Allow users to enter / exit dev mode as normal.
Change-Id: I168eb04a8ac102a8c4a1ca8936f78f62b001e0eb
Reviewed-on: https://gerrit.chromium.org/gerrit/59492
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Reviewed-on: http://review.coreboot.org/4321
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On some systems there may be 2GB SKU that is the same as the
4GB SKU but just one channel of memory. In that case we need
to ensure that both copies of the same SPD source end up
populated by ensuring that repeated entries are included by
using $+ instead of $^.
Alternatively we could do the check inside romstage, but it
is already set to behave this way if the SPD gets populated
correctly.
I changed spd_index to 3 in falco romstage to force it to
pretend it was a 2GB config of the same memory, then booted
to ensure it was indeed limited to 2GB.
memcfg channel[0] config (00780008):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 2048 MB width x16 single rank, selected
DIMMB 0 MB width x16 single rank
memcfg channel[1] config (00600000):
ECC inactive
enhanced interleave mode on
rank interleave on
DIMMA 0 MB width x8 single rank, selected
DIMMB 0 MB width x8 single rank
Change-Id: Ibfe5051ccda2fe69e8caff3f3c264116e3411c65
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59483
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Jay Kim <yongjaek@chromium.org>
Reviewed-on: http://review.coreboot.org/4319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The OIPG package needs to have >1 member to make the chromeos_acpi
kernel driver do the right automagic sysfs topology creation.
Additionally an "unimplemented" GPIO should be reported as 0xFF
because 0 is a valid GPIO number.
verify crossystem on slippy
$ sudo crossystem | grep -e recoverysw_cur -e wpsw_cur
recoverysw_cur = (error)
wpsw_cur = 1
Change-Id: I06dff09152bde30a3ffe58b1defe9d299155472c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57471
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4221
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This config option was not enabled which was preventing
the user from enabling developer mode from recovery mode.
With this enabled we can disable the "dev mode by default"
behavior and let people enable it by entering recovery mode.
This will make the firmware behave like a typical chromeos
device.
Peppy is left in "default dev mode" until after bringup.
1) boot slippy in normal mode by default
2) enter recovery mode with servo button
3) Ctrl+D on USB keyboard to enter developer mode
4) boot slippy in developer mode
Change-Id: I414c0d10dd0489e3c89798f75a2872a43297c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57350
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4220
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4219
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Currently, all Peppy boards w/ '000' SPD GPIOs have 2GB DRAM. Disable
the second DRAM channel based upon the GPIOs.
Need to change / confirm this for upcoming builds.
Change-Id: I7085ddecb80626cc0bed99ba7b174c6b80350696
Reviewed-on: https://gerrit.chromium.org/gerrit/58620
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4238
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC was disabling flash commands and sysjump was not working
properly. With those two fixed software sync works properly.
(Taken from I63ca00d6c94854f2b395eb736ce20792da5f8de2).
Change-Id: I9c7d1d1f1aaf7de33d0cec5f6daf648576ba8900
Reviewed-on: https://gerrit.chromium.org/gerrit/57289
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
Also sync pin states from Falco initial commit.
Reference change: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Change-Id: I66e136d389d53a367436d816fa84dacdc8e86bad
Reviewed-on: https://gerrit.chromium.org/gerrit/58334
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/4247
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
Reviewed-on: http://review.coreboot.org/4237
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Peppy RAM ID table is as follows:
000 41K256M16HA
001 H5TC4G63AFR
010 EDJ4216EFBG
Elpida SPD taken from Ib1e430cd390b4dbc013fc0802f1a59c1a0412577 by
dlaurie.
Change-Id: Iac156a2d25435514f28e2e73bef617d0fe2d90a1
Reviewed-on: https://gerrit.chromium.org/gerrit/56687
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4201
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Taken directly from slippy with only constant + string changes.
(Peppy port of I4172460d3b075bfd5bb22013a6225cf0e8f95b9c by dlaurie)
The following changes are required in a subsequent commit:
- Add Elpida SPD data.
- Update GPIO map.
- Remove iSSD power sequencing.
- Update USB port map.
Change-Id: I01dfb841f0e9186cf8a0a23f72e7be986a83be42
Reviewed-on: https://gerrit.chromium.org/gerrit/56513
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4200
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
