Apply tuning for the PCH I2C buses on Eve based on rise/fall time
measurements that were done with a scope.
BUG=chrome-os-partner:59686
BRANCH=none
TEST=Manual testing on Eve P1 to verify that all devices on I2C
buses are still functional. Post-tuning measurement will be done
once a new firmware is released.
Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18487
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Enable Fast-Plus speed for the touchscreen device so it can
be used at 1MHz instead of 400KHz.
BUG=chrome-os-partner:61277
TEST=manual testing on Eve P1, needs backported kernel patches
to actually make use of any I2C speed other than 400KHz
Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the audio devices to Eve mainboard:
- Describe Maxim 98927 speaker amps and RT5663 headphone codec
in ACPI so they can be enumerated by the OS.
- Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH.
BUG=chrome-os-partner:61009
TEST=manual testing on Eve P1 with updated kernel to ensure that
both speakers and headset are functional. DMIC support is
is still being worked on and is not yet functional.
Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18398
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The devicetree settings were incorrect in a few places with
respect to the SOC and board design:
- IMVP8 VR workaround is for MP2939 and not MP2949 on Eve
- IccMax values are incorrect according to KBL-Y EDS
- USB2[6] is incorrectly labeled
- I2C touch devices do not need probed as they are not optional
- PCIe Root Port 5 should be enabled
- I2C5 device should not be enabled as it is unused
BUG=chrome-os-partner:58666
TEST=manually tested on Eve board
Change-Id: I74e092444ead4b40c6d8091b80a691d44e2c6c7d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18200
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set the thermal throttle (prochot) activation to be 10 degrees
below TJmax so PROCHOT# kicks in at 90C instead of 100C.
BUG=chrome-os-partner:58666
TEST=boot on eve, check msr value before and after resume:
> iotools rdmsr 1 0x1a2
0x000000000a6400e6
> echo mem > /sys/power/state
> iotools rdmsr 1 0x1a2
0x000000000a6400e6
Change-Id: I3ab3a050a1e27c18a940bd7519eabaf015ef93eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17901
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Enable the actual touch devices to be probed by the kernel
and remove the placeholder devices that I put in before
and were used for initial bringup.
BUG=chrome-os-partner:58666
TEST=tested on eve
Change-Id: I7fc6f9da83b1abbae6dd069f759b220d59153d1c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17896
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
On this board i2c3 bus is connected to the display TCON, but it is
acting as the master when it has power so it can read from its own
EEPROM on the bus. In order to prevent any possible issues in S0
make these pins input on the SOC.
BUG=chrome-os-partner:58666
TEST=tested on eve board, but this bus was not used before so
there is no visible change in behavior.
Change-Id: Ide32f45ee33ca986fd3249a5161e01edf99d6e22
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17800
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In preparation of merging the lpss i2c config structures on
apollolake and skylake move the i2c voltage variable to its
own field. It makes refactoring things easier, and then there's
no reason for a separate SoC specific i2c config structure.
BUG=chrome-os-partner:58889
Change-Id: Ibcc3cba9bac3b5779351b673bc0cc7671d127f24
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17347
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add the eve board files using kabylake and FSP 2.0.
BUG=chrome-os-partner:58666
TEST=build and boot on eve board
Change-Id: I7ca71fe052608d710ee65d078df7af7b55d382bc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
