http://www.coreboot.org/pipermail/coreboot/2007-September/024665.html
It's about time we follow this advice.
Also move some manually set __PRE_RAM__ defines (ap_romstage.c) to the Makefile and
drop unused CPP define
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6482 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6467 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The cmos.default code wasn't actually used so far, due to an oversight
when forward-porting this feature from an old branch.
- Extend walkcbfs' use by factoring out the stage handling into C code.
- New sanitize_cmos() function that looks if CMOS data is invalid and
cmos.default exists and if so overwrites CMOS with cmos.default data.
- Use sanitize_cmos() in both bootblock implementations.
- Drop the need to reboot after writing CMOS: CMOS wasn't used so far,
so we can go on without a reboot.
- Remove the restriction that cmos.default only works on CAR boards.
- Always build in cmos.default support on boards that
USE_OPTION_TABLE.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6436 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reliability is accomplished by checking out the desired SeaBIOS commitish
into a branch named 'coreboot' in the local SeaBIOS git repository. Using
a branch allows TAG-$(CONFIG_SEABIOS_..) to refer to any commitish in the
SeaBIOS git repo, not just branches and tags.
Configuration is done with make defconfig followed by enabling and
disabling of the relevant coreboot-specific SeaBIOS options by appending
to .config using echo. This works, because later entries in .config will
overwrite earlier ones.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
VGABIOS, Intel MBI and the bootsplash image were added with special
build rules. These are replaced by generic cbfs-files-y entries now.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6320 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is in reponse to feedback that the original setup was too complicated.
New cbfs-files-y behaviour:
cbfs-files-y contains the names of files as they appear in CBFS. The
arguments describe the on-filesystem name, the type and (optionally) the
position. Example:
cbfs-files-y += foo
foo-file := bar
foo-type := splashscreen
foo-position := 0xffff8000
This configures a CBFS file called "foo" that is marked "splashscreen",
located at 0xffff8000 in flash and contains the data of the file "bar"
in the filesystem (either in the current directory, ie. where the
corresponding Makefile.inc resides, or if that doesn't exist, relative
to the toplevel directory).
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6319 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- actually hook up usbdebug in printk/print_ for romstage
- make usbdebug.c more similar to the Linux kernel version it was
originally derived from.
- increase retries and timing for usbdebug init (at least one chipset
seems to need this)
- src/pc80/usbdebug_serial.c is not needed
- some small console cleanups
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6315 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6291 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
defined if VGA_ROM_RUN is off. Define a dummy implementation of that
function for this case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6271 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6269 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to CBFS and adapt coreboot to use it.
Comments by Stefan and Mathias taken into account (except for
the build time failure if the table is missing when it should
exist and the "memory leak" in build_opt_tbl)
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6268 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that feature is not ROMCC compatible.
Fixes build errors introduced in r6253.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6255 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
If a file "cmos.default", type "cmos default"(0xaa) is in CBFS,
a wrong checksum leads to coreboot rewriting the first 128 bytes
(except for clock data) with the data in cmos.default, then
reboots the system so every component of coreboot works with the
same set of values.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add choice to use stable or master version of seabios repository
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6223 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence drop the FALLBACK_ prefix
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6204 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- move some variables where they belong
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6186 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We currently use "COREBOOT" unconditionally as the "OEM ID" in our
mptable.c files, and hardcode the mainboard name in mptable.c like this:
mptable_init(mc, "DK8-HTX ", LAPIC_ADDR);
However, the spec says
"OEM ID: A string that identifies the manufacturer of the system hardware."
(Table 4-2, page 42)
so "COREBOOT" doesn't match the spec, we should use the hardware vendor name.
Thus, use CONFIG_MAINBOARD_VENDOR which we have already as the "OEM ID"
(truncate/fill it to 8 characters as per spec).
Also, use CONFIG_MAINBOARD_PART_NUMBER (the board name) as "product ID",
and truncate/fill it to 12 characters as per spec, if needed.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
That variable allows chipset components to add files to
the CBFS image, for details see
http://www.coreboot.org/pipermail/coreboot/2010-December/062483.html
Compared to the patch in that mail this commit improves dependency
tracking a bit.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6182 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/arch/x86.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The files debug.asl, globutil.asl, and statdef.asl are duplicated in
many K8/Fam10h boards. However, they're neither board-specific nor
K8/Fam10h-specific nor AMD-specific, so move them to src/arch/i386/acpi.
debug.asl contains generic chunks for I/O port 0x80 handling, and debug
output over serial port (init COM port, send byte, send string, etc).
globutil.asl contains utility methods for string comparison, string length
and similar stuff.
statdef.asl contains generic ACPI bit definitions / status codes from
the ACPI spec (not board- or chipset-specific).
This patch was mostly generated by:
mkdir src/arch/i386/acpi
svn add src/arch/i386/acpi
svn cp src/mainboard/amd/dbm690t/acpi/debug.asl src/arch/i386/acpi/
svn cp src/mainboard/amd/dbm690t/acpi/globutil.asl src/arch/i386/acpi/
svn cp src/mainboard/amd/dbm690t/acpi/statdef.asl src/arch/i386/acpi/
cd src/mainboard
find . -name debug.asl -exec svn rm {} \;
find . -name globutil.asl -exec svn rm {} \;
find . -name statdef.asl -exec svn rm {} \;
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6156 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
using it directly again.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6118 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should probably be C code in some .c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Mention full name of all the tables (SSDT, FADT, etc).
- Drop obsolete / incorrect "LXBIOS" reference.
- Add missing ACPI address space type #defines specified in newer versions:
ACPI_ADDRESS_SPACE_EC, ACPI_ADDRESS_SPACE_SMBUS.
- Add missing "enum acpi_apic_types" entries: Localx2Apic, Localx2ApicNMI.
- Add ACPI_FACS_64BIT_WAKE_F #define.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix whitespace, coding style, and indentation in some places.
- Add comments for less obvious entries and hardcoded numbers (e.g. 'type').
- Add comments for all/most 'revision' fields, mention in which version
of the ACPI spec which revision number is to be used.
- Add URLs to a few external documents which describe tables that are
not mentioned in the ACPI spec (or where the external document may
provide further info), e.g. SRAT, SLIT, HPET, MCFG, etc.
- Use the ASLC #define instead of hardcoding "CORE" in one instance
(ASLC is already used everywhere else).
- Add some TODOs for additional stuff which is in the spec but not yet
handled by our code / #defines.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Updated patch with improved comments and small bugfix (use same
value for min and max on io resource).
While adding the area between TOM1 and 4GB to \SB.PCI0._CRS seems to be the
easiest way to get both Linux and Windows happy, it is not quite correct
because reserved areas like APIC, MMCONF etc. ranges need to be excluded.
This is a proof of concept patch for the M2V board that dynamically creates a
ResourceTemplate() containing these in the SSDT and adds a corresponding
PNP0C02 device to the DSDT.
All resources that have IORESOURCE_RESERVE and (IORESOURCE_MEM or IORESOURCE_IO) set
are added.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Added M2V-MX SE too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6084 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop sig[], oem[], and productid[] fields in all mptable.c files, no
longer needed. The sig[] is always the same ("PCMP"), the oem[] is
currently also always the same ("COREBOOT"), and productid is being
passed into mptable_init() directly as string now.
- LAPIC_ADDR is passed in as parameter, too. While at the moment it's
always the same value that is passed in, the LAPIC base address could
also be relocated theoretically, so keep it as parameter for now.
- Fix a few productid entries, they were (partially) incorrect:
- DK8S2 (was "DK8X", copypaste)
- 939A785GMH (was "MAHOGANY", copypaste)
- X6DHE-G (was "X6DHE", incomplete board name)
- H8DME-2 (was "H8DMR", copypaste)
- H8QME-2+ (was "H8QME", incomplete board name)
- X6DHE-G2 (was "X6DHE", incomplete board name)
- X6DHR-iG2 (was "X6DHR-iG", incomplete board name)
- GA-M57SLI-S4 (was "M57SLI", incomplete board name)
- KINO-780AM2 (was "KINO", incomplete board name)
- DL145 G1 (was "DL145G1", small fix as per vendor website)
- DL145 G3 (was "TREX", wrong board name)
- DL165 G6 (was "HP DL165 G6", drop vendor)
- S2912 (was "S2895", copypaste)
- VT8454c (was "VIA VT8454C", drop vendor, lower-case "c")
- EPIA-N (was "P4DPE", copypaste)
- pc2500e (was "PC2500", incorrect name)
- S1850 (was "S2850", copy-paste)
- MS-7135 (was "MS7135")
- MS-9282 (was "MS9282")
- MS-9185 (was "MS9185")
- MS-9652 (was "K9ND MS-9652")
- Ultra 40 (was "ultra40")
- E326 (was "E325", copypaste)
- M4A785-M (was "TILAPIA", copypaste)
- P2B-D (was "ASUS P2B-D", drop vendor)
- P2B-DS (was "ASUS P2B-DS", drop vendor)
- Adapt the mptable utility to use mptable_init() too.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As both ioapic.h and acpi.h define a macro named "NMI", rename one
of them (NMI -> NMIType in acpi.h).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The file is actually just including a bunch of assembly. The build rule
for bootblock.c even states that the file will be "assembler-with-cpp."
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5941 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
wonder why variables in .data or .bss (both somewhere in ROM space)
are wrong.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5841 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
statement to those files that actually need it. This significantly
reduces the number of dependencies, so it's no longer extremely ugly to
specify them manually (see the src/pc80/Makefile.inc portion)
- Add double include guards around option_table.h defines
- Also, drop the AMD DBM690T work around for the issue
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5838 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
used for source level debug.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes a few alignment wrinkles and sets up and registers the MMCONF area
for AMD Fam10h CPUs (where selected by mainboard configuration). It
removes a bit of code that proved troublesome in MMCONF setups from
mcp55_early_setup_car.c, as per earlier discussion.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5796 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Trying to keep it simple: Two sizes are expected equal so use same %x for both.
Cast to unsigned int to make sure it fits.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop lots of dead code from the various cache_as_ram.inc files.
- Use some descriptive macros instead of magic numbers for MTRR MSRs
- drop unused duplicate descriptors from romstage GDT
- slightly reformatting code and comments
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5696 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
