No changes in content of the files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes minor coding style issues and prepares the table for supporting
more chips of the ITE IT87xx Super I/O family.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2750 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Common code sequences have been factored out, the code has been made
more generic, has better handling of corner cases and is actually much
shorter.
It also adds probing for almost all recent (since 1999) ITE Super I/O
chips to probe_superio. I did verify against all ITE datasheets
(including those not available any more) that the probing was
non-destructive.
For the ITE IT8712F, the complete configuration is dumped and as
comparison the default value from the data sheet is printed.
More information can be extracted easily, however this needs loads of
datasheet surfing.
This code has been tested extensively, dumping for other ITE chips will
follow as a separate patch.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2749 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The first byte of the flash chip was read at the start of the function
and later written back to address 0 if the flash chip was not identified
as SST28SF040, which means most of the time. This write caused corruption
of flash contents when verifying a SST49LF160C part.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M50FLW080B, M50FW080, M50FW016, M50LPW116, M29W010B flash chips made
by ST to flashrom.
The patch is based on the data sheets of the chips and has not been
tested at all.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2741 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only reading from the chips was tested; writing support is untested.
Thanks to Gürkan Sengün <gurkan@linuks.mine.nu> for testing!
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Generic driver for pretty much all known Standard Microsystems Corporation
(SMSC) Super I/O chips.
Most of the SMSC Super I/O chips seem to be similar enough (for our
purposes) so that we can handle them with a unified driver.
So far only the ASUS A8000 has been tested on real hardware!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2734 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(SMSC) Super I/O chips.
Most of the SMSC Super I/O chips seem to be similar enough (for our
purposes) so that we can handle them with a unified driver.
So far only the ASUS A8000 has been tested on real hardware!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Same board enable as Asus A7V8-MX. Tested by Reinhard Max.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Now uses CAR.
New code for SPD-less memory implementation.
Updated IRQ routing.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2728 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the system boot to a command line.
This patch comments out the code to set up the vga framebuffer to allow
the system to boot, without this fix the system hangs during elfboot.
The only line that is absolutely necessary to change is the SMRAM setup,
however I've commented out all vga setup to make it very obvious to both
the kernel/payload and anyone looking at the code that vga isn't
currently working. This setup might also be better handled in
northbridge.c, if it doesn't need to be done before ram init, yet
another reason to comment it all. In the future, LinuxBIOS needs to be
told that the graphics memory area, 1mb or 512kb (at the user or
developer's option), is reserved for the onchip vga, but I'm not sure if
it's taken at the top or bottom of the memory, yet. LB may also need to
set a base address for the AGP aperture and/or be told that range is
reserved as well, whether this was originally the job of the system bios
or vga bios is still a mystery. It also corrects the number of entries
in irq_tables.c, without this fix the kernel would probably complain and
hang due to unmapped IRQs.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2725 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
more than just one way. This version should be (more) correct.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2723 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2720 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The DB800 is the AMD LX Reference Design Kit platform.
For details see: http://www.amd.com/geodelxdb800
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Still hardcoded for Tyan S1846.
This slightly increases performance, but it's still pretty horrible.
Some RAM settings are causing a dramatically slow system (confirmed
by comparing memtest performance results of the proprietary BIOS
and our code). Haven't found the problem, yet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2717 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both are very similar, thus both use the JUKI-511P target.
Linux with patches from Juergen Beisert
(http://www.linuxbios.org/pipermail/linuxbios/2007-May/020932.html)
boots and work fine (ide, usb, ethernet, serial, keyboard and sound
work normally).
Problems:
- Filo loads a bzImage only from ide0 (ide1 doesn't work yet).
- Video doesn't work, yet.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2716 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The previous code was pretty unreadable, undocumented and did some totally
unrelated things (such as mucking with the game port or port 0x92).
This version is tested with a 256 KB chip and should work for the
CS5530 and CS5530A.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2715 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Linux booted with the proprietary BIOS reports 2e.f as PS/2 mouse
in the output of 'lspnp -v'.
- The floppy on 2e.f was a typo, should have been 2e.e from the beginning.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2709 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Super I/O part was incorrect.
Also, add ide0_enable/ide1_enable variables, and enable both the
primary and secondary IDE interface per default.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2708 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
return that skipped the disable code. This patch removes the return and
fixes the UART disable code.
The problem was that the disable code was ORing bits into the Legacy_IO
MSR causing issues with the LPC SIOs init code that would manifest as a
hang because the IO would not be decoded correctly. ANDing to clear the
bits fixes the issue.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Sven Kapferer <skapfere@rumms.uni-mannheim.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2704 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In a mainboard's Config.lb file you can configure whether the primary
and/or secondary IDE interfaces shall be enabled.
Also, various fixups in the rest of the southbridge code, most notably
the early SMBus code, plus some documentation improvements.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As per JEDEC, we should wait 200us until voltages and clocks are stable.
Then apply NOPs for 200 clock cycles (for simplicity we use 200us here).
All other delays are so low that we get away with just waiting 1us.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2702 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Only check the RAM from 0 - 640 KB and 768 KB - 1 MB now. That's
available on all boards, regardless of what DIMMs you use.
Tested on the Tyan S1846, works fine.
- Properly set the PAM registers to allow the region from 768 KB - 1 MB
to be used as normal RAM (required for the above).
- Document all of this properly. Add/improve other documentation, too.
- Simplify and document code in northbridge.c.
- Cosmetics and coding style.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
accessible (but not writable), so that reading/loading a payload
from that area can work (for instance).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2700 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It moves the complete naming functionality to
src/cpu/amd/model_fxx/processor_name.c.
The current code sets the processor name string twice for Rev. F CPUs.
In src/cpu/amd/model_fxx/model_fxx_init.c the function
amd_set_name_string_f is called first. Several lines later
init_processor_name is called which doesn't recognize newer CPUs and
actually programs incorrect values, thus overwriting the previously set
CPU name. For example, this resulted in identifying an Opteron 2218 as a
Turion processor.
This patch removes the amd_set_name_string_f function from
src/cpu/amd/model_fxx/model_fxx_init.c and adds support for Rev. F CPUs
to src/cpu/amd/model_fxx/processor_name.c as described in the Revision
Guide for AMD NPT Family 0Fh Processors, AMD Document ID 33610 Rev 3.00,
October 2006.
Signed-off-by: Sven Kapferer <skapfere@rumms.uni-mannheim.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2699 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann