Follow up to https://review.coreboot.org/#/c/18460/
Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
According to USB 2.0 Spec Table 7-7, the High-speed squelch
detection threshold Min 100mV and Max 150mV, and we set USB
2.0 PHY0 and PHY1 squelch detection threshold to 150mV by
default, so if the amplitude of differential voltage envelope
is < 150 mV, the USB 2.0 PHYs envelope detector will indicate
it as squelch.
On Kevin board, if we connect usb device with Samsung U2 cable,
we can see that the impedance of U2 cable is too big according
to the eye-diagram test report, and this cause serious signal
attenuation at the end of receiver, the amplitude of differential
voltage falls below 150mV.
This patch aims to reduce the PHY0 and PHY1 otg-ports squelch
detection threshold to 125mV (host-ports still use 150mV by
default), this is helpful to increase USB 2.0 PHY compatibility.
BRANCH=gru
BUG=chrome-os-partner:62320
TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into
Type-C port, check if the USB device can be detected.
Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e
Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/431015
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18462
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
As David commented the "Bob and other follow-ons match Gru, Kevin should
be the special case here", and update the calculations value for gru/bob
board.
From the actual tests, some regulator voltage than the actual set of less
than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the
{min, max} regulator voltage for Bob board. Make sure we get the accurate
voltage.
BUG=chrome-os-partner:61497
BRANCH=none
TEST=boot up Bob, measure the voltage for little cpu and C-logic.
Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4
Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/424523
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Original-Reviewed-by: Brian Norris <briannorris@chromium.org>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430403
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18460
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch adds the DPTF settings specfic to the mainboard and enables
the CPU and other thermal sensors as participant device for poppy.
It enables the DPTF flag in the device tree for poppy. It also includes
the DPTF specific ASL file in the main DSDT definition.
BUG=None
BRANCH=None
TEST=Built for poppy.
Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17926
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Once the PCI command register is written the bridge forwards
future IO and memory regions, as programmed in the respective base
and limit registers, to the secondary PCI bus.
It was previously argumented this is copy-paste and never known
to be required for these more recent platforms:
https://review.coreboot.org/#/c/2706/
Change-Id: Ic8911500a30bc83587af8d4b393b66783fa52e18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18330
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
minnow3 doesn't build right now due to API divergence on master branch.
Follow up with recent changes.
Change-Id: Iee84750292f22aa040127bcbfe523a0b9eaa8176
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18476
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
The children of Gru should share the benefits. In the real world, Bob can't
pass the eye diagram tests.
BUG=chrome-os-partner:62714
BRANCH=firmware-gru-8785.B
TEST=build coreboot
Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd
Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/440745
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/441468
Reviewed-on: https://review.coreboot.org/18461
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Camera and Imaging device should be enabled for camera usecase,
FSP provides a UPD to enable/disable the SA IMGU (Imaging Unit)
expose the same as a config option in devicetree.cb
Also remove a redundant assignment for PchCio2Enable.
BUG=None
BRANCH=None
TEST=lspci should list 00:05:00
Change-Id: I4cf7daf41bfaf4dcba414921cac2e7e12bf89f37
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18365
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This enables some required Kconfig options when CONFIG_CHROMEOS is set.
Change-Id: I290902746c1ea19c8bcb69540e34fde09abb9adf
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/18448
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
This adds an oak libpayload config, that should fit all oak-based
devices such as elm.
Change-Id: Iabb71404ff84029a5976371a353e8c92e781ca1f
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/18447
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
These parameters are probably the result of copying from the Thinkpad
X60 code.
Change-Id: I29763b38618d4b306c37424c5c4b57dfcf69424b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18290
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set the proper memory configuration for the MinnowBoard 3. The current
values are copied from intel/leafhill. Set the proper values for
MinnowBoard 3.
Change-Id: Ie37842f5ce2cabaa892f42ee945c91fe3ace527a
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18374
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This commit adds the initial scaffolding for the MinnowBoard 3
with Apollo Lake silicon.
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with name changes. Special adaptations for MinnowBoard 3
mainboard will follow in separate commits.
Change-Id: I7563fe37c89511c7035c5bffc9b034b379cfcaf4
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18298
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This file reportedly didn't compile on SUSE Linux with gcc 4.3.4:
[...]
> HOSTCC cbfstool/fsp_relocate.o
> In file included from coreboot/src/commonlib/fsp_relocate.c:18:
> coreboot/src/commonlib/include/commonlib/fsp.h:26: error:
> expected '=', ',', ';', 'asm' or '__attribute__' before
> 'fsp_component_relocate'
[...]
According to POSIX-2008[1], sys/types.h defines ssize_t, so include it.
This should not break coreboot code (as opposed to utils code), as we
have a sys/types.h in src/include.
[1]: http://pubs.opengroup.org/onlinepubs/9699919799/basedefs/sys_types.h.html
Change-Id: Id3694dc76c41d800ba09183e4b039b0719ac3d93
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/18417
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martinroth@google.com>
This is more consistent with newer Intel targets.
Change-Id: I52ee8d3f0c330a03bd6c18eed08e578dd6ae284b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18371
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
There was a 'typo' where the subsystem id was set instead of the codec
vendor id. This caused the lynxpoint HDA codecs init to fail to find
the proper codecid verbs so codecs were never initialized. That caused
the headphones jack to not work.
Change-Id: I975031643fc42937ecaea2300639b90632543f67
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18411
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
The M.2 SSD is on the SATA port 3, which also required the DTLE setting
to be set.
This fixes issues with the M.2 SSD not being detected/stable.
Change-Id: Id39d9ec395a2d9d32be4c079678d0708f08b3935
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18409
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The Broadwell SATA controller supports IOBP registers on ports 0 and 1 but
Browell supports up to 4 ports, so we need to support setting IOBP for
ports 2 and 3 as well.
The magic numbers (IOBP SECRT88 and DTLE) for ports 2 and 3 were only
guessed by looking at ports 0 and 1 and extrapolating from there.
Port 3 has been tested (DTLE setting on Librem 13) and confirmed to work
so we can assume that port 2 and 3 magic numbers are valid, but having
someone confirm them (through non-public documents?) would be great.
Change-Id: I59911cfa677749ceea9a544a99b444722392e72d
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18408
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
In order to allow GPIOs to be set/clear according to their polarity,
provide helper functions that check for polarity and call set/clear
SoC functions for generating ACPI code.
BUG=None
BRANCH=None
TEST=Verified that the ACPI code generated remains the same as before
for reef.
Change-Id: Ie8bdb9dc18e61a4a658f1447d6f1db0b166d9c12
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18427
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18322
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Adding spi_xfer_two_vectors as .xfer_vector for ipq40xx spi_ctrlr.
Commit c2973d196d ("UPSTREAM: spi: Get rid of SPI_ATOMIC_SEQUENCING")
has added a new driver method xfer_vector to support combined write-read
operation within a single CS cycle. The method is wrapped in the
spi_xfer_vector() API. When spi_ctrlr structure does not have
xfer_vector method, API calls write and read operations sequentially.
However the QCA40xx SPI driver has "forced" CS activation-inactivation
in xfer method, so individual operation will break CS after write
operation, making combined write-read cycle broken.
Adding xfer_vector method to spi_ctrlr is a simple fix to prevent this.
BUG=None
BRANCH=none
TEST=built and run on Gale
Change-Id: I2258e563d0793bcacd626f78b8e96b3649a8e4a4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 88a8824951cef4fe293dfa6e3a1a837ae07b6156
Original-Change-Id: I031e85ce5b847353cb1084f6f68b2af8c6f702e1
Original-Signed-off-by: Yuji Sasaki <sasakiy@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433439
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/18297
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Adds the necessary plumbing for acpi_device_path() to find the LPC
bridge on the AMD Family14 northbridge with an SB800 southbridge.
This is necessary for TPM support since the acpi path to the LPC bridge
(_SB.PCI0.ISAB) doesn't match the built-in default in tpm.c
(_SB.PCI0.LPCB).
Change-Id: I1ba5865d3531d8a4f41399802d58aacdf95fc604
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18402
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
With recent change (a4b11e5c90: soc/intel/skylake: Perform CPU MP Init
before FSP-S Init) to perform CPU MP init before FSP-S init, suspend
resume is currently broken for all skylake/kabylake boards. All the
skylake/kabylake boards store external stage cache in TSEG, which is
relocated post MP-init. Thus, if FSP loading and initialization is
done after MP-init, then ramstage is not able to:
1. Save FSP component in external stage cache during normal boot, and
2. Load FSP component from external stage cache during resume
In order to fix this, ensure that FSP loading happens separately from
FSP initialization. Add fsp_load callback for pre_mp_init which ensures
that the required FSP component is loaded/saved from/to external stage
cache.
BUG=chrome-os-partner:63114
BRANCH=None
TEST=Verified that 100 cycles of suspend/resume worked fine on poppy.
Change-Id: I5b4deaf936a05b9bccf2f30b949674e2ba993488
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18414
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a function to allow FSP component loading separately from silicon
initialization. This enables SoCs that might not have stage cache
available during silicon initialization to load/save components from/to
stage cache before it is relocated or destroyed.
BUG=chrome-os-partner:63114
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae77e20568418c29df9f69bd54aa571e153740c9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18413
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
poppy board uses Maxim 98927 speaker codec and Realtek RT5663
for headset. Select the apropriate NHLT blobs to be packaged in CBFS.
Also, generate the required ACPI NHLT table for codec and the supported
topology in poppy.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=With the required driver support in kernel verify that
the Audio plays on on-board speakers and headset, recording
works from on-board mics and headset mics.
Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18214
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Wacom I2C driver does the same thing as I2C HID driver, other than
defining macros for Wacom HID. Instead of maintaining two separate
drivers providing the same functionality, update all wacom devices to
use generic I2C HID driver.
BUG=None
BRANCH=None
TEST=Verified that ACPI nodes for wacom devices are unchanged.
Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18401
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Enable Fast-Plus speed for the touchscreen device so it can
be used at 1MHz instead of 400KHz.
BUG=chrome-os-partner:61277
TEST=manual testing on Eve P1, needs backported kernel patches
to actually make use of any I2C speed other than 400KHz
Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18397
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the audio devices to Eve mainboard:
- Describe Maxim 98927 speaker amps and RT5663 headphone codec
in ACPI so they can be enumerated by the OS.
- Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH.
BUG=chrome-os-partner:61009
TEST=manual testing on Eve P1 with updated kernel to ensure that
both speakers and headset are functional. DMIC support is
is still being worked on and is not yet functional.
Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18398
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Created using autoport plus some manual work and copying from G505S to
account for the non-H8 EC.
This model uses the same ENE KB9012 EC as the G505S.
Tested:
- Mainboard variant with 8GB Elpida DDR3
- SeaBIOS payload
- Booting into Linux 4.9.6 with Debian/unstable installed on the
internal HDD/SDD slot
- Native raminit
- Both native VGA init and option rom VGA init
- Basic TPM functionality (auto-detection and RNG)
- Battery status readout
- Basic ACPI functions (power button event; power-off; reboot)
- thinkpad-acpi hotkey functions
- thinkpad-acpi LED control (red thinkpad LED)
- Suspend to RAM and resume works
- Mini displayport output works
Known issues:
- Patches needed for EC battery support
https://review.coreboot.org/#/c/18348/https://review.coreboot.org/#/c/18349/
- No thermal zone since temperature sensing is not H8-compatible
and needs to be reverse engineered.
Not tested:
- msata/wwan (probably works)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Change-Id: I52bc4515277e5c18afbb14a80a9ac788049f485c
Reviewed-on: https://review.coreboot.org/18351
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Since we are not using gpio regulators on reef anymore, remove the
selection from Kconfig as well.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18399
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This mainboard uses two i210 Ethernet controller. Therfore we enable the
usage of the i210 driver and have to provide a function to search for a
valid MAC address for all i210 devices by using Siemens hwilib.
Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18380
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Not selecting the Kconfig option `GENERATE_SMBIOS_TABLES` the build
fails with the error below.
```
CC ramstage/ec/lenovo/h8/h8.o
src/ec/lenovo/h8/h8.c:201:2: error: unknown field 'get_smbios_strings' specified in initializer
.get_smbios_strings = h8_smbios_strings,
^
src/ec/lenovo/h8/h8.c:201:2: error: initialization from incompatible pointer type [-Werror]
src/ec/lenovo/h8/h8.c:201:2: error: (near initialization for 'h8_dev_ops.read_resources') [-Werror]
cc1: all warnings being treated as errors
```
So add the appropriate preprocessor guards to fix the build error.
Change-Id: I3baed452d422539a805c628a8c4a6a8c2a809317
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17770
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Using x86 RDRAND instruction, two functions are supplied to
generate a 32bit or 64bit number.
One potential usage is the sealing key generation for SGX.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve to generate a 64bit random number.
Change-Id: I50cbeda4de17ccf2fc5efc1fe04f6b1a31ec268c
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18362
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently the USB OC pins definition only being defined up to OC3.
For PCH-H, OC4 and OC5 are needed, so add both into OC pin enum.
Changes is being verified and booted to Yocto with Saddle Brook.
Change-Id: Idaed6fa7dcddb9c688966e8bc59f656aec2b26eb
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/18364
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Jonathan Neuschäfer