From DDR4 SPD spec:
Byte 4 (0x004): SDRAM Density and Banks
Bits [7, 6]:
00 = 0 (no bank groups)
01 = 1 (2 bank groups)
10 = 2 (4 bank groups)
11 = reserved
Bit [5, 4] :
00 = 2 (4 banks)
01 = 3 (8 banks)
All others reserved
Separate DDR3 and DDR4 banks. And extened capmb, rows, cols and ranks.
Separate DDR3 and DDR4 ORGANIZATION/BUS_DEV_WIDTH offset.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5f56975ce73d8ed2d4de7d9fd08e5ae86993e731
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Based on HW schematic to modify USB setting.
Drallion has two type C on left and two type A on right.
BUG=b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I925de209635d92ef61ccb9114efebb4b10f30e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Sets all unused sata ports to disable in the device tree
Note:
SATA4 and SATA5 are located at the bottom of the board, but there
is no connector for this. Apparently, a board with an increased
number of ports is very rare. Perhaps this is a separate variant
of the Asrock motherboard. For this reason, these ports are also
disabled
Change-Id: I5b3ad372f1d6607cc7b4a78e3c59d2a5ae1d2cf5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Disable spi0, i2c0 and i2c1 in the “SerialIoDevMode” register for the
following reasons:
1. when the AMI BIOS is used, these pci devices are disabled in
lspci.log;
2. there are no pads in the inteltool.log that use the functions of
these buses
Change-Id: I01ab10eb3fd41e81a1726805247c2b472d72287c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35070
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The string "register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" was mistakenly
taken from the Intel KBL-RVP8 devicetree.cb. Remove it, since the i2c4
bus is disabled in the "SerialIoDevMode" register
Change-Id: I44ecd5c22efd66b02a2851dc14a1a95421f39a71
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
1) VR domains current limit Icc max for Sky/Kaby Lake S is set based
on the processor TDP [1]. Updates information about this
2) Sets VR voltage limit to 1.52V, as described in the datasheets [2,3]
[1] Change-Id: I303c5dc8ed03e9a98a834a2acfb400022dfc2fde
[2] page 112-119, 6th Generation Intel(R) Processor Families
for S-Platforms, Volume 1 of 2, Datasheet, August 2018.
Document Number: 332687-008EN
[3] 7th Generation Intel(R) Processor Families for S Platforms and
Intel(R) Core(TM) X-Series Processor Family Datasheet, Volume 1,
December 2018, Document Number: 335195-003
Change-Id: I6e1aefde135ffce75a5d837348595aa20aff0513
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The MCFG ACPI table was not being created.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35bdefb2a565d18917a2f6517d443890f93bd252
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Decide if HECI1 should be hidden prior to boot to OS.
BUG=none
TEST=Boot to OS, verify if Heci1 is disabled on hatch system
using FSP 1344.
Change-Id: I7c63316c8b04fb101d34064daac5ba4fdc05a63c
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
The documentation for StackBase and StackSize in FSPM_ARCH_UPD is
confusing. Previously the region was shared for heap and stack,
starting with FSP2.1 only for heap (or 'temporary RAM') for HOBs.
Moving the allocation outside DCACHE_BSP_STACK_SIZE allows use of
stack guards and reduces amount of reserved CAR for bootblock and
verstage, as the new allocation in .bss is only taken in romstage.
BUG=b:140268415
Change-Id: I4cffcc73a89cb97ab7759dd373196ce9753a6307
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
TPMU_HA is a union of all the different hash digests, and so
sizeof(TPMU_HA) evaluates to 64 (the size of the largest one). This will
lead to out-of-bounds writes when copying smaller digests, so use the
specific digest size for each algorithm.
Change-Id: Ic9101f157d5a19836b200ecd99f060de552498d2
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 14049{49,50,51,52,53,54,55,56,57,58,60,61,62}
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Include the file containing the typedefs for uint_*.
Change-Id: I3eae80a677e9d6932dc115523da2c0819a371fa7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35268
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Include the file containing the typedefs for uint_*.
Change-Id: Ib0eea9bfd0c8d9e3eba257b561980accf5b4bab4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35267
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the new SuperIO ACPI generator to make includes in DSDT obsolete.
Manually tested on X11SSH-TF and verified that ACPI tables are correct.
Change-Id: I2ef49bb6f733994b249ae46f0460234380b552b8
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33253
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds Lewisburg C62x Series PCH support by adding the
Production and Super SKUs of the following PCI devices:
- LPC or eSPI Controllers,
- PCI Express Root Ports,
- SSATA and SATA Controllers,
- SMBus,
- SPI Controller,
- ME/HECI,
- Audio,
- P2SB,
- Power Management Controller.
These changes are in accordance with the documentation:
[*] page 39, Intel(R) C620 Series Chipset Platform Controller Hub
(PCH) Datasheet, May 2019. Document Number: 336067-007US
Change-Id: I7eaf2c1bb725ffed66f86c023c415ad17fe5793d
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Add a generic SuperIO ACPI generator, dropping the need to include
additional code in DSDT for SuperIO.
It generates a device HID based on the decoded I/O range.
Tested on Supermicro X11SSH-TF using AST2400.
The SSDT contains no errors and all devices are present.
Possible TODOs:
* Add "enter config" and "exit config" bytes
* Generate support methods to enter and exit config mode
* Generate support methods to query, change or disable current
resource settings on specific LDNs
Change-Id: I2716ae0580d68e5d4fcc484cb1648a2cdc1f4ca0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Some USB 3.0 devices fail to be enumerated after USB reset, and xhci
port status register shows the device is disconnected. After measuring
the USB signal, we found that the USB disconnect threshold was lower and
that the disconnect event was triggered unexpectedly.
USB designers suggest changing discth to 15.
BUG=b:122047652
TEST=emerge-kukui coreboot chromeos-bootimage
Change-Id: I0e8556035b49d693a42cbe1099a6882a1c0ed0d1
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
These devices can be accessed directly by symbolname,
without a search and walk through the tree, as they
have static paths.
Change-Id: I711058f5c809fa9bc7ea4333aaebad6847ebdfd4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31933
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Vendor only does dummy reads right after JEDEC init is finished
and dram init was marked as finished.
Dummy reads also make much more sense after JEDEC init as a way to
send a few JEDEC commands, presumably as a way to make sure it is
ready.
TESTED on ga-g41m-es2l (still boots fine)
Change-Id: I8069f9c08ad5e5268ddbe3711d58bc42522f938c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/20979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Based on HW schematic to modify PCIE setting.
BUG=b:138082886
BRANCH=N/A
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia744a6f3cba76c507c1c43b0a981cb6d89c1a40f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Use sku-id to load the SAR values for Bloog device.
BUG=b:138180187
BRANCH=octopus
TEST=build and verify load Bloog SAR by sku-id
Cq-Depend: chromium:1771477
Change-Id: Id0bc2609fd1c4eaeb380f8f1532ab30d34e2aeb3
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
To avoid possible panel failures due to incorrect timing settings for
PTN3460, the internal graphic device should be disabled.
Change-Id: Ie0b9ed99fb78461bb48d6f2ff328643cd8c2cd15
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Add printing SPD data for debug usage.
BUG=b:139397313
BRANCH=N/A
TEST=Tested the on Hatch and checked cbmem log.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1e257a8ea6ff9c906267841819d2a4b62a9e0b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To support multi digists the tlcl_extend() for TPM2 expects
TPML_DIGEST_VALUE pointer as input argument.
BUG=N/A
TEST=Build binary and verified logging on Facebook FBG-1701
Change-Id: I8d86c41c23e4e93a84e0527d7cddcfd30d5d8394
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Currently SPI vendor IDs are magic numbers in spi_flash.c. These definitions
are needed for AMD's fch_spi. So add the definitions to spi_generic.h and use
it at spi_flash.c
BUG=b:136595978
TEST=Build test of several platforms that don't use stoneyridge. Build and boot
grunt (using stoneyridge new fch_spi).
Change-Id: Ie39485d8c092151db8c9d88afaf02e19c507c93f
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
Rename the table from Liara specific to simply specifying
that it's using 2T command rate
BUG=139841929
TEST=build and do stress test
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6e10b95c8aea50e68d8a3b710f30dda4f6b807d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
override 'uint32_t sku_id(void)' so that lib_sysinfo.sku_id get a
correct value in depthcharge
BUG=b:140010592
BRANCH=none
TEST=boot treeya board, in depthcharge stage, lib_sysinfo.sku_id
print correct value.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I631f62021e8104a69a43667a811c9c23e3105596
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Magf - <magf@bitland.corp-partner.google.com>
Reviewed-by: Edward Hill <ecgh@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Padmelon board code was written for Merlin Falcon (family 15h models 60h-6fh),
but as the needed binaries are not yet merged (commit 33615), a config
HAVE_MERLINFALCON_BINARIES was added. If the binaries are not available,
the board defaults to Prairie Falcon, which use the same binaries as Stoney
Ridge. Once the binaries are merged, the config will be eliminated. Fan
control is done through F81803A SIO, and IRQ/GPIO and other board
characteristics are the same regardless of Merlin Falcon or Prairie Falcon.
Padmelon board was created to accept Prairie Falcon, Brown Falcon and Merlin
Falcon. The requested development was for Merlin Falcon. There are some small
spec changes (such as number of memory channels) between SOCs. Brown Falcon
was not investigated, Prairie Falcon is very similar to Stoney Ridge.
Started from Gardenia code, added changes created by Marc Jones and finally
revised against schematic, which added changes to GPIO settings.
BUG=none.
TEST=Both versions tested and boot to Linux using SeaBIOS.
Change-Id: I5a366ddeb4cfebd177a8744f6edb87aecd4787dd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Consider the association between modem[1] and DCXO, this patch is a fix for
eb5e47d("mediatek/mt8183: update dcxo output buffer setting") [2]
We should not disable XO_CEL and block the bblpm request when modem is still ON.
For power-saving, we still could disable unused XO_CEL and
mask request to disable unused power mode when modem is no longer be used.
[1] https://review.coreboot.org/c/coreboot/+/32666
[2] https://review.coreboot.org/c/coreboot/+/32323
BRANCH=none
TEST=Boots correctly on Krane.
Change-Id: I047ebed615e874977ca211aafd52b5551c71b764
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Line length limit was bumped to 96 characters, but the coding style did
not reflect such a change.
Change-Id: Ifdbb8bc04e49e1fbe9b0c8a642ae814d5a60004a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
mashal_TPMT_HA() uses size of SHA-256 hash.
Use tlcll_get_hash_size_from_algo() to determince the hash size.
BUG=N/A
TEST=Build binary and verified logging on Facebook FBG-1701
Change-Id: I739260e13e9cd10a61d52e13e8741b12ec868d7f
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The P2SB PCI device can be "hidden", which causes all sorts of
nightmares and bugs. Moreover, FSP tends to hide it, so finding
a good solution to this problem is impossible with FSP into the mix.
Since the values for IBDF and HBDF were already hardcoded as FSP
parameters, define them as macros and use these values directly to
generate the DRHD.
Change-Id: I7eb20182380b953a1842083e7a3c67919d6971b9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mimoja <coreboot@mimoja.de>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add fan based active cooling for TSR sensors temperature range.
BUG=b:138966929
BRANCH=None
TEST=Verified Fan control functionality for TSR sensors on Hatch.
Change-Id: I957ae96cf6fa7d2467e73155d64f76a6bd652e31
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
tsc_freq_mhz() had a static table of Intel CPU families and crystal
clock, but it is possible to calculate the crystal clock speed dynamically,
and this is preferred over hardcoded table.
On SKL/KBL/CML CPUID.15h.ecx = nominal core crystal clock = 0 Hz
hence we had to use static table to calculate crystal clock.
Recommendation is to make use of CPUID.16h where crystal clock frequency
was not reported by CPUID.15h to calculate the crystal clock.
BUG=b:139798422, b:129839774
TEST=Able to build and boot KBL/CML/ICL.
Change-Id: If660a4b8d12e54b39252bce62bcc0ffcc967f5da
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35148
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sridhar Siricilla