This matches the _HID used in the picasso UEFI bios.
BUG=none
BRANCH=zork
TEST=boot linux and verify peripherals still work
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ieb441696cbe67a772632990347c12d1d15cfaf13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is the new _HID that was used for Raven. It matches the _HID used
by the picasso UEFI bios.
This does change the fixed clock used by linux from 133 MHz to 150 MHz.
BUG=none
BRANCH=zork
TEST=boot linux and verify touch screen and touchpad still function
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I37fcb4a4f0148f4843d026902d694c03aeed3c3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This is the new _HID that was used for Raven. It matches the _HID used
by the picasso UEFI bios.
BUG=none
BRANCH=zork
TEST=boot linux and verify UART still works
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I138cb445c84997f4a4006cbb4f6617dac25a61b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Change the hardcoded location of microcode patches to using
FIRMWARE_LOCATION.
Change-Id: Iae3d159aa5413a416c54935ab7a809d0f4ff776f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49734
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For board version 6 afterward, it will have external pull-up for
GPP_C12, and remove internal pull-up.
BUG=b:177618684
TEST=emerge-dedede coreboot, check evtest if SW_PEN_INSERTED event
(value:1/0) when insert/eject pen, and eject pen to wake system from s0ix
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I503873afb48384168dcd8a822c7246655898356e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
set pwron_varybl_to_blon to 0x5, which means fw will delay 20ms between backlight
on and vary backlight.
BUG=b:171269338
BRANCH=zork
TEST=Build; Verify the UPD was passed to system integrated table; measure
the power on sequence on dalboz
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I8af35eee7777a8e71b42f0c128795290b8c2c93e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Add UPDs for eDP power sequence adjust
all pwr sequence numbers below are in uint of 4ms.
BUG=b:171269338
TEST=Build; Verify the UPD was pass to system integrated table; measure
the power on sequence on dalboz
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I6eceebd1c3f522e6a8dfaadc487a590107ae3131
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48864
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add UPDs for eDP power sequence adjust.
BUG=b:171954512
BRANCH=zork
TEST=Build, verify the parameter pass to picasso-fsp
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ic4bafd86ffb7804c4739f9d30beb67549b71d289
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
All callsites of `rmw_1d0` use the same `flag` value.
Change-Id: I84fab5d3fd270ce684cd6ca892c213b0d8610283
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reference code does not run any DMI recipe for Sandy Bridge. Create a
helper function and exit early for Sandy Bridge. The CPUID value will
be used in a follow-up, since DMI setup has stepping-specific steps.
Change-Id: I5d7afb1ef516f447b4988dd5c2f0295771d5888e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48413
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop the old, redundant code for mirroring LPC registers to DMI and make
use of the new common code.
Select the new Kconfig option for LPC DMI mirroring by the option
SOC_INTEL_COMMON_PCH_BASE, which is selected by platforms starting with
SPT, except APL and Xeon-SP. For Xeon-SP, select DMI and the new Kconfig
directly.
APL, even though it's younger than SPT, does not need mirroring.
Test: Set LGMR address by calling `lpc_open_mmio_window` and check that
both the PCI cfg and DMI LGMR register get written correctly.
Tested successfully on clevo/cml-u.
Change-Id: Ibd834f1474d986646bcebb754a17db97831a651f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Starting with SPT, LPC registers IOD, IOE, LGIR* and LGMR need to be
mirrored to their corresponding DMI registers. Add the required writes
to DMI registers, where the PCI config registers get written.
This is already done in soc code for IOD, IOE and LGIR* by mirroring
the registers later, during PCH init. Also the code mostly matches
accross the platforms. This common implementation will avoid delayed
mirroring of the registers and also deduplicate the code.
This change also adds a new Kconfig that will be selected by platforms
requiring mirroring of LPC IO/MMIO registers to their corresponding DMI
registers.
For making use of this common code, the redundant soc code needs to be
dropped and the newly introduced Kconfig option has to be selected. This
is done in the follow-up change.
Change-Id: I39f3bf4c486a1bbc112b2b453381de6da4bbac4d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Instead of hardcoding paths to the executables, use the version in the
path. This allows the scripts to work on more systems, and allows the
binary version to be changed more easily if needed.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ifcc56aa21092cd3866eacb6a02d198110ec6051d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Put this in a new directory called 'infrastructure' and make a link
and an index.md file for the directory.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I54a0204e7525a25f2fd717a73007b304aac67396
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
According to FSP_INFO_HEADER structure in FSP EAS v2.0-v2.2,
BIT1 indicates an "official" build.
Change-Id: I94df6050a1ad756bbeff60cda0ebac76ae5f8249
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
"usb2_ports[7]" for internal bluetooth device was configured as
'USB2_PORT_EMPTY' mistakenly in previous patch, so we need to enable
it again.
BUG=None
BRANCH=firmware-dedede-13606.B
TEST=Built and verified BT device existence with lsusb
Change-Id: Id2900152e23bbc2f454d064dc86a9e45e934ea0f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch adds explicit initializations for the remaining named display
(power) control GPIOs to the bootblock GPIO init code. These pins are
usually mapped to pins that are already configured to pull-downs on
power-on reset so this wasn't really required, but we have already moved
them around so often that you never know when EEs might one day move
them to a pin with a different power-on reset configuration, so it's
better to be explicit.
In one particular case, GPIO(67) (used by CoachZ rev1+ but not by
anything else for the EN_PP3300_DX_EDP pin) is not actually a pull-down
on boot, even though that is claimed by the datasheet. This is likely
due to the fact that it can serve as the SPI_HOLD pin for the boot flash
QSPI bus, so even though our board's boot flash doesn't really use that
pin, it seems that the boot ROM still configures it as such.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I533baa962d2dfc87cfa510f442ed2e8912e0e5b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This will remove "ARCH_ARMV8_EXTENSION=0" from ".config" when unneeded.
Change-Id: Idd4ad67fb4a3efdb0864803f87c6b5f508fb4364
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Commit 393992f (cpu/mp_init: Fix microcode lock) fixed the semantics
of parallel loading microcode updates.
So now '*parallel = 1' really means loading MCU in parallel, which
seems to fail inconsistently on around 10% of the APs.
Change-Id: I755dd302abbb58537d840852e8e290bea282a674
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49671
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When MAINBOARD_HAS_SPEAKER is false, the SPKR gets _HID PNP0C02. This
conflicts with the LDRC device. PNP0C02 is also used other places in the
picasso code base, so I chose a random _UID for each device. The _UIDs
are unique in the code base so it's easy to search for duplicates.
BUG=b:175146875
TEST=Boot trembyle to linux
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I01be41515e011293e90a6b42b8e34de8ec3ffc18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This conflicts with the MSTH i2c_tunnel.
BUG=b:175146875
BRANCH=zork
TEST=Boot trembyle and inspect ACPI tables.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iac04c7dc361d427f5ebb99644aa70bd0c7dbb918
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
If a _HID/_CID are not unique, we need to add a _UID field to
differentiate the objects.
BUG=b:175146875
BRANCH=zork
TEST=Boot linux, dump ACPI table and verify UIDs are unique
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Icd2ccede2b6c2e332157e2eeca89fba14a46b360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This file was added here before util/docker existed. Anyone using this
dockerfile should use the coreboot-sdk docker container instead.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I7114abc9c91ba2d6fcfef80ae6e7d1a7a3d253cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It's easier to understand what these symbolic names mean rather than
using the constants; the static.c will will end up (indirectly)
including `soc/usb.h` therefore the macros are in scope here.
Change-Id: I5ef977a05a2522e177f32c99bfab74f9288ae869
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
From AMD USB phy specialist recommended that for DB port2 (type-A), port3 (type-C C1)
the most effective corrections for the depressed eye are
tx_rise_tune=0x0
tx_pre_emp_amp_tune=0x3
tx_fsls_tune = 0x3
BUG=b:173476380
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass USB 2.0 SI eye diagram verification
Change-Id: Ib31c5d55e30b958d3e552e8d0b4a160947444636
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
From AMD USB phy specialist recommended that for DB port2 (type-A), port3 (type-C C1)
the most effective corrections for the depressed eye are:
tx_rise_tune=0x0
tx_pre_emp_amp_tune=0x3
tx_fsls_tune = 0x3
BUG=b:165209698
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass USB 2.0 SI eye diagram verification
Change-Id: I80afd6bf1257b9a72d0d7651b48d243ebaf5de2f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
The only difference is an additional include that is no longer needed.
Change-Id: I0053d03aa4d05f5c0fa833d8634419b6667e38a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49832
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no need to repeat the same code on every board.
Change-Id: I2e19decfe8609fa644e609673a56ee5109bafefa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49831
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change uses the newly added meminit block driver and updates TGL
SoC and mainboard code accordingly.
TEST=Verified that UPDs are configured correctly with and without this
change.
Change-Id: I6d58cd6568b7bbe03c4e3011b2301209893e85a9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Raul E Rangel