Linux boots fine :)
Change-Id: Ifda06e5220666534b87f528deae16d8b956c32b3
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1225
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This register is helpful for porting new mainboards based on
cs5536 southbridge.
Change-Id: Iff3adc2c2fbc672c8541096756f95b3322f6ab19
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1211
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch adds support for autogenerating the MPTABLE from
devicetree.cb. This is done by a write_smp_table() declared
weak in mpspec.c. If the mainboard doesn't provide it's own
function, this generic implementation is called.
Syntax in devicetree.cb:
ioapic_irq <APICID> <INTA|INTB|INTC|INTD> <INTPIN>
The ioapic_irq directive can be used in pci and pci_domain
devices. If there's no directive, the autogen code traverses
the tree back to the pci_domain and stops at the first device
which such a directive, and use that information to generate the
entry according to PCI IRQ routing rules.
Change-Id: I4df5b198e8430f939d477c14c798414e398a2027
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1138
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Missed to add the driver to Kconfig and Makefile.inc.
Change-Id: I64b02abc5de2f6483f610436ebb38a7ca433f9b6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1219
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
All but one board use the default value of enabled. Disabling
this can only increase the number of MTRR registers used.
Change-Id: I7d28adc31b9fae2301e4ff78fcb96486f81d5ec2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1213
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Implemented OHCI reset function ohci_reset() in ohci.c
for libpayload's USB driver.
Change-Id: Id6518cbe00a21202757b34926bad171909740e97
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1177
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support to dump all data registers for Nuvoton chips (NCT6775F, NCT6776F,
and NCT6779D). Register contents will be dumped if the -e option is provided on
the command line.
Change-Id: I2b425b48c1f28a10ff3c1ca1d7f21c501eff74ad
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-on: http://review.coreboot.org/1150
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add new function dump_data() to dump a bank of superio data registers.
Change-Id: I13a58d87c14d319cfcdea1ec1d54c2b110d90f9f
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-on: http://review.coreboot.org/1149
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
There are two errors in the code. The first one is a missing
$ sign in mov _stack, %esp. Thanks to Ronald G Minnich for
catching that bug.
The second bug is the 'incl %eax', which shouldn't be there, as
there's no secondary CPU with index 0. CPU0 uses always the stack
below _estack.
Change-Id: Id267a654ba95b0e898eeaaafb2403b438250a563
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If a CPU was pre-allocated, cpu_path is not copied and thus
index would not be updated. This breaks cpu_index() and AMD
model_fxx is possibly broken without this patch.
Change-Id: I77483181cf0bca31423c655942c022bffab3c7ea
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1199
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
If threads called alloc_find_dev() with same device_path
simultaneously, two device nodes could be allocated.
This bug is not triggered by current code.
Change-Id: Ifc87021c8d6f422901c5de5dd17392e3e2309afa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1188
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Remove superfluous pkg* definitions and installation of a target
directory directory that is never used.
Change-Id: I2addf3f316230cdd428def5889fd3beb7c40f422
Signed-off-by: Raymond Danks <ray.danks@se-eng.com>
Reviewed-on: http://review.coreboot.org/1195
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Not all users use both functions, so add __attribute__((unused))
to prevent compiler errors.
Change-Id: I8485bb9150b04d1f9fdc231152a43bcd6fc713a7
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1193
Tested-by: build bot (Jenkins)
Don't stop if RAM init fails at first try. It's better to restart
and try again instead of failing on the first try if the second
try would have worked.
Change-Id: Ib5660265d5b10a01588f2e4022dac2ee34f2c6d0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1191
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Implements support code for talking to IPMI hardware that uses
a KCS style interface.
Change-Id: I9895cc1bf29676115b167081b63b8a430e23eee5
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1190
Tested-by: build bot (Jenkins)
The Kconfig file for this board contains a bogus option called
CORE_GLIU, this change removes it.
Change-Id: I4ea069bdd76be53085ebc9c0fb3dd71ffb2a12e1
Signed-off-by: Ricardo Martins <rasmartins@gmail.com>
Reviewed-on: http://review.coreboot.org/1179
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This is mostly necessary for reboot, but it doesn't hurt the boot process.
On reboot explicitely reset the integrated graphics, otherwise the VGABIOS
might not be able to reinitialize it properly, and you either have a still
of the last pre-reboot image, garbage or an empty screen, but no text-mode.
Change-Id: Ic3d6932fbaf720d88daaac7e4b09c3c0b9f0b0e2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1178
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The superiotool Makefile extracts a version string from SVN. This does not work
with a git repository, and results in an empty version string. Use the output of
'git describe' as version string instead.
Change-Id: Idf92c02753b28ef5bcdd3b6df4a08d79ae974434
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-on: http://review.coreboot.org/1151
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
PCI Type 2 config was a strange and never-used config mechanism.
It is unlikely that in the 13 years of coreboot's existence that
type 2 was ever used; it just made life complicated for everyone.
It lived long enough in coreboot to be replaced by mmioconf.
Prior to making the device tree visible in romstage we want to
get rid of type2.
Delete two files we don't need any more (yay!).
Replace two functions with one: pci_config_default, which returns
a pointer to the default config method. At some future time this
may change to mmio but for now it is old type1 style.
Change-Id: Icc4ccf379a89bfca8be43f305b68ab45d88bf0ab
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1159
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
The SIPI vector copy can use a static location below 1MB, aligned
to 4kB. Jump out of the copy once in protected mode.
Change-Id: I6299aa3448270663941cf2c4113efee74bcc7993
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1165
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
CACHE_ROM_SIZE default is ROM_SIZE, the Flash device size set
in menuconfig. This fixes a case where 8 MB SPI flash MTRR setup
would not cover the bottom 4 MB when ramstage is decompressed.
Verify CACHE_ROM_SIZE is power of two.
One may set CACHE_ROM_SIZE==0 to disable this cache.
Change-Id: Ib2b4ea528a092b96ff954894e60406d64f250783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1146
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Diff between model_106cx and model_6ex CAR codes suggests currently
used model_106cx CAR is not optimal - destination RAM and source ROM
of ramstage copy_and_run are only partly set cacheable.
It appears variable MTRR setting for XIP cache is left enabled on
model_106cx code, where it should have extended to cover all of Flash.
Introduces untested functional change on boards:
intel/d945gclf
iwave/iWRainbowG6
Deletes file:
model_106cx/cache_as_ram.inc
Change-Id: I35229f8433927e83821e72e9d9a9fc8fb09c3f1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/642
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
A diff from model_6fx to model_106cx suggests there is little
CORE2 specific code that was once considered useful to have.
In its current status however, sockets supporting model_6fx use
model_6ex CAR init, so that specific code is actually
never used.
Deletes file:
model_6fx/cache_as_ram.inc
Change-Id: I6c0204446fa98207e31f91895e1cf30fde42382c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/640
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Used for automatic generation of IOAPIC interrupt entries.
Change-Id: Ia746f01906c840800956ce551306f864e440b6ec
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1137
Tested-by: build bot (Jenkins)
Default CPU_ADDR_BITS is 36.
For Atom (model_106cx) use 32. This model is known to
fail execution-in-place (XIP) with the default 36.
Pentium M should use 32, but doesn't even with this patch.
Some Xeon and CORE(2) models should use 38 or 40.
Change-Id: If604badcdc578c4f4bc7d30da2f61397ec0d754c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/639
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
used for fan control and thermal management on that board.
Change-Id: I4e5c986ab6174b7a356d682e21732c46181af211
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1167
Tested-by: build bot (Jenkins)
awk on Cygwin created the UTF-8 value for the 0xff code point,
which makes it two bytes wide. This broke the build.
Change-Id: I4937ae7ce1136ba7a76d05b42f9dd2771203175d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1164
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
With this change it is possible to define serial number
and version of the mainboard. These informations are used
in SMBIOS tables.
Change-Id: I1634882270f6cb94e00aceb7832e7fd14adc186b
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1163
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The error message from romstage is annoying and misleading:
"Do not use global variables in romstage"
Because it can occur even when global variables are not used
in some circumstances, but also because it gives you only a rough
idea where to look. This change sucks but sucks less. We still don't
know which file the problem is in but at least we know if it is data
or bss.
Replace the error message with something that provides more information
and less guessing on the part of the script:
".bss is non-zero size in romstage which is not allowed -- global variable?"
or
".data is non-zero size in romstage which is not allowed -- global variable?"
To test: build coreboot as normal. It builds.
Add
char d[32];
to romstage.c and get the first error message; add
int x = 32;
to romstage.c and get the second.
Change-Id: I300ec05bdb4b30d7ef3f5112e6cc09b1fafe8263
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1160
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The new broadcast code doesn't support serial init - if a CPU
needs serial init, this should be handled in the model specific CPU
init code.
Change-Id: I7cafb0af10d712366819ad0849f9b93558e9d46a
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1140
Tested-by: build bot (Jenkins)
The current code for initializing AP cpus has several shortcomings:
- it assumes APIC IDs are sequential
- it uses only the BSP for determining the AP count, which is bad if
there's more than one physical CPU, and CPUs are of different type
Note that the new code call cpu->ops->init() in parallel, and therefore
some CPU code needs to be changed to address that. One example are old
Intel HT enabled CPUs which can't do microcode update in parallel.
Change-Id: Ic48a1ebab6a7c52aa76765f497268af09fa38c25
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Early HT-enabled CPUs do not serialize microcode updates within a core.
Solve this by running microcode updates on the thread with the smallest
lapic ID of a core only.
Also set MTRRs once per core only.
Change-Id: I6a3cc9ecec2d8e0caed29605a9b19ec35a817620
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1142
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Correct registers base (PCI BAR) reading to be
more specification friendly. Registers base
only in [31-12] bits, all other proposed to be 0
but that not true for some motherboards. So
adding mask to use only valid bits.
Change-Id: I2e9a4997e016dab812ccfe654e966bc91d42a625
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1143
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
As we using 16-bit reading and writing in UHCI drive,
so all variables related to that must be 16-bit too.
Change-Id: Ib1abb03d054c167512e21f24f3c3da688c7fd01f
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1144
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
They used MP_IRQ_TRIGGER_LEVEL, but it should be MP_IRQ_TRIGGER_EDGE.
While at it, uses mptable_lintsrc() instead.
Change-Id: Ie71311b8bf865889cf0d8808467df98af4b0132d
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1136
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This adds basic supported for the Supermicro X7DB8. Basic means that
almost all onboard peripherals are working. Known problems are:
- mptable needs to be written dynamically. If you plan to use Add on
cards, modify mptable.c according to your needs. A patch to add generic
mptable autogeneration based on devicetree is coming up.
Change-Id: I5eaac32a8bafa69a05929cf08d869127b9464661
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/493
Tested-by: build bot (Jenkins)
Required for Supermicro X7DB8, which needs the FBDIMM clock generator
setup during romstage.
Change-Id: I30ca8354087e851487aee0614595782131d4d9bc
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1116
Tested-by: build bot (Jenkins)
Christian Gmeiner