* Use dedicated ALERT pin to resolve NO_RESPONSE error/status while
getting target configuration.
* Configure the ESPI to operate at 16 MHZ since operating at 33 MHz
causes boot stall.
BUG=b:226635441
TEST=Build and Boot to OS in Skyrim. Ensure that EC <-> AP communication
is working fine through Host Command debug logs in EC console, ectool
version command.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I951afdada8ee4f917cdeba8e287e5a2ae77c97ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63286
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Found an issue where emmc and sd clocks were being misconfigured due
to using incorrect integer values when called instead of the defined
enums. Fixing by splitting the clock_configure_sdcc() function into
two (sdcc1 and sdcc2) as there was no commonality between the two
cases anyway. As a result, we can also get rid of the clk_sdcc enum.
BUG=b:198627043
BRANCH=None
TEST=build herobrine image and test in conjunction with CB:63289
make sure assert is not thrown.
Change-Id: I68f9167499ede057922135623a4b04202f4da9b5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The Dell OptiPlex 9010 uses a Q77 PCH, which is Panther Point. The only
difference is the definition of the `CROS_GPIO_DEVICE_NAME` macro, which
is not used for non-ChromeOS coreboot builds.
Change-Id: I7ad07b464aef24f7749c3fe9300b7f7dd865e47b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
The PCH's PCIe ports do not support Gen3 speeds, only Gen1/Gen2.
Change-Id: I7df61af1953ec99000c6c501b017e553190a46b6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
It was enabled due to known compatibility issues with Qubes OS.
Since the release of R4.1.0, this issue is no longer present so
it can be disabled.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iab6048dc93112b9365f0c2b46225569073eb32f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Andy Pont <andy.pont@sdcsystems.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
elog_gsmi_cb_mainboard_log_wake_source is called from SMI and causes
eSPI transactions. If the SMI interrupts an ongoing eSPI transaction
from the OS it will conflict and cause failures. Removing this call to
avoid conflicts. This can be re-enabled after refactoring
google_chromeec_get_mask to use ACPI MMIO.
BUG=b:227163985
BRANCH=gubyrush
TEST=No 164 errors detected during suspend_stress_test
/sys/firmware/log output after resume before change:
SMI# #1
ELOG: Event(B0) added with size 9 at 2022-03-31 19:52:51 UTC
GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000
ELOG: Event(9F) added with size 14 at 2022-03-31 19:52:51 UTC
Chrome EC: clear events_b mask to 0x0000000000000000
after change:
SMI# #6
ELOG: Event(B0) added with size 9 at 2022-03-31 19:50:19 UTC
GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000
ELOG: Event(9F) added with size 14 at 2022-03-31 19:50:19 UTC
Change-Id: I3320e3fb8bd9e9e0db84332e1d147a0af25f7601
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63280
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enabling rtd3 reduces power consumption when the SSD is idle.
Tested and verified on the StarBook Mk V (TGL), using PowerTop
on Manjaro 21.2.5 GNOME at 20% Brightness.
Signed-off-by: Stephen Edworthy <stephen@starlabs.systems>
Change-Id: I0d8aa185a322bb8d1aba51ccaab03c521cec2770
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
BUG=b:226848617
TEST=HDMI works on nereid
Cq-Depend: chrome-internal:4650256
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I6a90d3d86b32f73ec0130e582539d1c5b045da62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
BUG=b:226848617
TEST=HDMI works on nereid
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I039c30f95d959dba489b24b6938d08da937c5e03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
BUG=b:226848617
TEST=With the following change, the nereid C1 PMC mux conn is disabled
based on fw_config, allowing HDMI to work.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I487f3ca4be4ead0c5dfb46e9eb19de5ae9b9bda9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63237
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support for ELAN trackpad on I2C0 bus.
BUG=None
TEST=Build and boot to OS in Skyrim. Perform evtest on Elan trackpad.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia1522af3f35ef131dda74c4aabecc4fa532dfbec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add a stack in .bss for C execution. This will make it easier to move
the setup of MTRRs in C code.
Change-Id: I67cbc988051036b1a0519cec9ed614acede31fd7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Removing unnecessary "czn" in variable name. Majolica is always a
cezanne.
TEST=Timeless build
Change-Id: I490111ecea84c934585d0bbd623486fba76eb7f1
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63261
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove "czn" from the variable names since chausie does not use cezanne.
TEST=Timeless build
Change-Id: I8cc854f4c60707c7fec5cd7fef1c4550883cd45a
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Since Sabrina uses the image slot header (ISH) that depends on the AMD
A/B recovery scheme that depends on the multi-level PSP directory
support, the multi-level support gets automatically selected by passing
Sabrina as SoC name to amdfwtool, so passing the --multilevel command
line switch to amdfwtool isn't needed.
TEST=Timeless build results in identical binary for chausie
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I98154d5b47daca6ae7952ffd3175d98ea3e01845
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
The fch_i23c_pad_init implementation was written without looking at any
reference code and turned out to not work properly on hardware. Before
this function writes to the MISC_I23C_PAD_CTRL registers, the value read
back is 0x3000003c which results in the I2C bus communication to work
while the 0x300003fc the code writes to the register breaks the I2C
communication. Removing the code that sets bits 6..9 fixes the I2C bus
communication.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ie6758b3d13c59b20ce810225fca8a365713b7a2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63234
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Contradicting the PPR #57243 version 1.56, the I2C3 pad control register
in the MISC ACPIMMIO region is the same new I23C pad type as the
corresponding registers for I2C0..2 and not the older I2C pad control
register type used on Picasso and Cezanne. All I2C pads being of the new
I23C type is in line with the GPIOMUX settings for the pins used by
I2C0..3 that can alternatively connect the pins to an I3C controller.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I51b0ddf8ba2ccfee823e3d4d26a77b11825b1029
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63233
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to PPR #57243 version 1.56, the IOMUX setting 2 of the pins 19
and 20 is the I3C3 controller and not the I2C3 controller.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9688f1816aa840c64441495ed451997a474b306f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63232
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When masking out bits with an and mask, the bit mask needs to be
inverted.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9739d7150e230fbbe6523413de9c07d7340f3c61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63222
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I23C_PAD_CTRL_SLEW_N_SHIFT is 6 and not 7 which matches both with the
PPR #57243 revision 1.53 and with I23C_PAD_CTRL_SLEW_N_MASK which covers
both bits 6 and 7.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I622717bebaffe34b6df5e578b082dc10e2a98256
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63216
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Turn off the NFC power which is controlled by GPP_D3 to save power in
S0ix states. For an USB device, the S0ix hook is needed for the on/off
operations to take place.
BUG=b:202737385
BRANCH=firmware-brya-14505.B
TEST=measure the voltage of GPP_D3 in S0ix states
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I69588c82dfde1744c45c7aff3ac05b80bb16a8f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
On x86 ramstage is always relocated at runtime in cbmem so there is no
need to have this configurable in Kconfig.
Change-Id: I01b2335d0b82bea8f885ee5ca9814351bbf2aa3c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63215
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We set T3 as 300ms to meet Elan's spec, but the resume/suspend times
are greater than 500ms, which is the spec for Chromebooks.
The actual kernel timing has been measured, and given the ACPI delay
after deasserting reset in addition to the delay until the kernel
driver accesses the device, delaying only 200ms in the ACPI method is
also sufficient to meet the 300ms requirement.
BUG=b:223936777
BRANCH=none
TEST=build and test touchscreen function on DUT.
TEST=suspend, wake DUT and check touchscreen function.
Change-Id: I6b04cf6392d924aed01ca36b720f889b88d92311
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
C0 has no redriver, so enable SBU muxing in the SoC.
C1 has a redriver which does SBU muxing, so disable SBU muxing in the
SoC. However, this also disables AUX biasing when the pins are
configured as NF6. So instead configure the C1 AUX bias pins as GPO.
BUG=b:227259673
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: Ic0af662ecc1c6cee15b4ae98cb02deeefc93a71e
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Add new board Clevo L14xMU (TGL).
GPIOs were configured based on schematics.
Tested and working:
- On-board RAM (M471A1G44AB0-CWE)
- DIMM slot (tested Crucial CT16G4SFD8266.16FJ1 / MTA16ATF2G64HZ-2G6J1)
- Graphics (GOP driver), including HDMI
- Keyboard
- I2C touchpad (including interrupt)
- TPM (with interrupt on Windows, only polling on Linux [1])
- microSD Card reader
- both NVME ports
- Speakers
- Microphone
- Camera
- WLAN/BT (CNVi)
- All USB2/3 ports including Type-C
- Thunderbolt detects my work laptop in TB Control Center
(I couldn't test anything more due to security policy.)
- TianoCore
- internal flashing with flashrom on vendor firmware
Note on TPM:
The vendor sets Intel PTT to default-on in newer CSME images, which
conflicts with the dTPM. Currently, there are two ways to make it work:
1) Boot vendor firmware once to let it disable PTT via CSME firmware
feature override.
2) Use Intel Flash Image Tool (FIT) to set "initial power-up state" to
disabled.
Boots fine:
- Debian testing, unstable (Linux 5.16.14, 5.17.0-rc6)
- Windows 10 21H2 (Build 19044.1586)
Untested:
- Thunderbolt (see above)
- Type-C DisplayPort
- S-ATA
Doesn't work:
- TPM interrupt on Linux [1]
- All EC related functions - EC driver is WIP
- WLAN/BT (PCIe) - gets detected but can't be enabled
- 3G/LTE (not powered without EC driver)
- Fn-Keys
- S0ix
- UCSI
- Fan control
- Battery info
[1] https://lkml.org/lkml/2021/5/1/103
Change-Id: I4c4bef3827da10241e9b01e12ecc4276e131a620
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
When rebuilding coreboot the empty fit table added to added to CBFS
stays the same so the build process sees no reason to update the file.
In the meantime ifittool did update that file for instance to add
microcode update entries. So each time coreboot is rebuilt the entries
are appended to the FIT table which runs out of space at some point.
One way to deal with this is to clear the fit table when setting the
pointer inside the bootblock.
TESTED: Now running 'make' again on prodrive/hermes does not report an
error with a filled FIT table.
Change-Id: Ia20a489dc90a4ae704e9ee6d532766899f83ffcc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63036
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When setting the FIT pointer, the FIT table is only known later in the
codeflow.
Change-Id: I658f4fffa997d1f7beaf6d6ae37d2885ae602e5c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63035
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EE requested that we increase the drive strength for the SPI lines to
8mA.
BUG=b:198627043
BRANCH=None
TEST=EE help verify
Change-Id: Ic887a7eef74f1063f7284db042c5fbd2e1d5bd4c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Flame graphs are used to visualize hierarchical data, like call stacks.
Timestamps collected by coreboot can be processed to resemble
profiler-like output, and thus can be feed to flame graph generation
tools.
Generating flame graph using https://github.com/brendangregg/FlameGraph:
cbmem -S > trace.txt
FlameGraph/flamegraph.pl --flamechart trace.txt > output.svg
TEST=Run on coreboot-enabled device and extract timestamps using
-t/-T/-S options
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I3a4e20a267e9e0fbc6b3a4d6a2409b32ce8fca33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Some of these targets seem to come from a long time ago. Now just
rm -rf $(obj) is all that is needed for a clean.
Change-Id: Iccc62b3c54ee2a074c25674715403c1457f6aad3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
Based on the latest schematic, agah will replace the Maxim 98390
speaker amps with Maxim max98360. This patch updates the
devicetree entries to reflect that.
BUG=b:210970640
BRANCH=brya
TEST=emerge-draco coreboot
Change-Id: I7ea36d276f7ffeae1510483027092e2bc59690fc
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Brask set GPP_D0 to GPO in commit b0769db4, but Kinox doesn't support
fingerprint. This patch sets GPP_D0 to NC for matching schematic.
BUG=b:214025396
BRANCH=firmware-brya-14505.B
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I38b9eb2df83cfbdb58d95cb178c1d767299aa4da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The do_send_end_of_post function is implemented in the cse_eop.c file.
This change adds the Kconfig SOC_INTEL_CSE_SET_EOP in cse.c to avoid
build issue.
Change-Id: Ib52404d9ad4c01a460e4cfef331c529d2a53337a
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
The headers are now unused, drop them.
Change-Id: Ibfaa3029ddc614935481ce736c9d971bf4831b5d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On platforms using UDK2015 select UDK2017 instead.
This allows to drop UDK2015 headers.
Tested using timeless builds: The produced binaries are identical.
Change-Id: Ia6032c6520ec889cd63655db982d9bfa476dc24d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Replace LShiftU64 and RShiftU64 as the defined macro conflicts with
UDK2017 headers.
Tested using timeless builds: The produced binaries are identical.
Change-Id: I8f205f663be9c9c31cf384ca89370afa48ca1e15
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Fix return type of early_init_get_elapsed_time_us() to comply with the
data type of return value.
Also replace memset() with struct initializer.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Fixes: commit 41faa22 (soc/mediatek: Add early_init for passing data
across stages)
Change-Id: I7c361828362c2dfec91358ad8a420f5360243da0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
RF team comfirmed that SAR sensor is not necessary for MP,
therefore remove the corresponding entries from the devicetree.
BUG=b:202978964
TEST=Build pass.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I31faf18563848f8d6787fe70bfb28006efea8427
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fill in the memory config based on the the schematic by bernadino 14 adl-p 20220112.pdf
BUG=b:219891328
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I981d2cd6feafee8c10ec9724a3dec9a23ba0ddd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The patch logs CSE RO's write protection information for Alder Lake
platform. As part of write protection information, coreboot logs status
on CSE RO write protection and range. Also, logs error message if EOM
is disabled, and write protection for CSE RO is not enabled.
TEST=Verify the write protection details on Gimble.
Excerpt from Gimble coreboot log:
[DEBUG] ME: WP for RO is enabled : YES
[DEBUG] ME: RO write protection scope - Start=0x1000, End=0x15AFFF
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I766d5358bb7dd495b4a9b22a2f1b41dc90f3d8d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Now that the amdfwtool support for Sabrina is in place, change the
SoC name parameter passed to amdfwtool from Cezanne to Sabrina.
The fw.cfg file still points to the Cezanne binaries, but since
commit 9cb0a05dfb (soc/amd/sabrina: Add
prompt for AMDFW_CONFIG_FILE) this can be overridden via the Kconfig
config file in the build. As soon as the Sabrina PSP binaries are
available in 3rparty/amd_blobs, the fw.cfg file will be updated to use
the correct ones for Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I53a8de222e39bd2b92c07661b6c52a02fb651609
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63189
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PSP_S0I3_RESUME_VERSTAGE Kconfig symbol is only defined in the
Cezanne Kconfig, so drop this from the Sabrina makefile.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9571a302d427981cdf750a1cb3b7f4db9d61a87c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63188
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Karthikeyan Ramasubramanian