Taken directly from slippy with only constant + string changes.
(Peppy port of I4172460d3b075bfd5bb22013a6225cf0e8f95b9c by dlaurie)
The following changes are required in a subsequent commit:
- Add Elpida SPD data.
- Update GPIO map.
- Remove iSSD power sequencing.
- Update USB port map.
Change-Id: I01dfb841f0e9186cf8a0a23f72e7be986a83be42
Reviewed-on: https://gerrit.chromium.org/gerrit/56513
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Dave Parker <dparker@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4200
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
RAM_ID indices have been changed and settled on a 2GB config
that will be the same DRAM chips but only used in one channel.
Change-Id: I444e655883ae045622ab3dfb964da4d7f86e1c0d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56810
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4198
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are placeholder values until we can configure for
the exact panel.
Change-Id: If40367c0e5f80d46d085c89b0edae60f1ccacdaf
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56808
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4197
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The haswell i915 kernel driver apparently expects the VBIOS
to set a few specific registers. This sequence is enough to
make the driver happy without executing the VBIOS.
This also makes graphics work after suspend/resume.
Change-Id: I34937d55ffff8a9445442e6e6ca1bfc49869da63
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56806
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4195
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the onboard I2C devices for Falco trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
Change-Id: Ibe9687b2f7f41ead18353c3f650219fe6e94ae2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4191
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the onboard I2C devices for Slippy trackpad/lightsensor
and generate SMBIOS Type41 tables for them.
Add ACPI device for the trackpad to expose the interrupt map
to the OS so it can be used.
Configure interrupt GPIOs as PIRQ type and wake GPIOs as
just standard input type. The wake GPIO is reconfigured as
ACPI SCI in the specific device _DSW method. This prevents
the wake GPIO from generating a flood of SCI at runtime.
LTE_WAKE_L_Q and WLAN_WAKE_L_Q are left as ACPI SCI as these
are not repurposed interrupt pins so they are not generated
at runtime.
SIM_DET and ALS_INT_L are set as input since we don't have an
interrupt handler for them.
tested on slippy with trackpad with additional
kernel changes to chromeos_laptop.c to initialize devices.
1) Ensure trackpad interrupt is functional and that there
is not a flood of ACPI SCI when trackpad does interrupt:
9: 1 0 0 0 IO-APIC-fasteoi acpi
37: 421 0 0 0 IO-APIC-fasteoi cyapa
2) Ensure that devices are exposed as wake capable:
Device S-state Status Sysfs node
TPAD S3 *enabled pnp:00:00
TSCR S3 *disabled pnp:00:01
3) Ensure that trackpad can wake from S3 by default, but
that it does not cause an immediate wake when entering suspend.
4) Ensure that trackpad can be disabled as a wake source with
echo TPAD > /proc/acpi/wakeup
Change-Id: Id562d20b54eeefec56040b8f70ef238911312628
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56622
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4190
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is an LPT-LP specific method that will enable a specific
GPIO as an ACPI SCI wake source.
It can be used by a device _DSW method to enable a pin that is
otherwise not configured to generate SCI at runtime.
It will set:
- GPIO owner to ACPI
- GPIO route to SCI
- GPIO config to GPIO, Input, Inverted
Also clean up and remove ACPI field definitions that are unused
and/or incorrect.
Change-Id: I14acc2de50e6200f61c2898a7bd1252400e0f0be
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56621
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4189
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This was provided by the vendor but I added the part number at
byte 128-143 so it can be identified when extracted by mosys.
Change-Id: Ib1e430cd390b4dbc013fc0802f1a59c1a0412577
Reviewed-on: https://gerrit.chromium.org/gerrit/56634
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4192
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In addition to not clearing the pending interrupts, we also
don't want to reset the RTC control register when booting
with an S3 resume.
On most new systems, when the RTC well is losing power, we
will also lose state that is required to perform a resume,
so we end up in a normal boot anyways. Hence don't do any
RTC initialization in the S3 resume path.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I73b486082faa741e9dccd15f2b8e3a8399c98f80
Reviewed-on: https://gerrit.chromium.org/gerrit/56826
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4206
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some code was previously removed regarding elf notes. However,
that code left a dangling comma under !CONFIG_MULTIBOOT
configs for inline assembly constraints. Instead, place the comma
within the #ifdef stanza.
Change-Id: I805453ef57d34fbfb904b4d145d8874921d8d660
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56844
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: David James <davidjames@chromium.org>
Reviewed-on: http://review.coreboot.org/4207
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These GPIO accesses were copied by accident and don't
make sense for the baskingridge board.
Change-Id: I03bfc2cf97b6056a746a6c1a27308823ecaa9637
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4204
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
LynxPoint-LP has an additional 16 entries in the IOAPIC that
can be assigned to specific GPIOs when they are configured
as PIRQ.
The maximum redirection entries field in the IOAPIC needs to
be set to 0x27 when this is enabled.
Additionally specific GPIOs need to be routed to PIRQ so they
interrupt via the IOAPIC instead of the GPIO IRQ 14/15.
Change-Id: Ie587e1d203422ff6fb7fc5056d20a5ae66720991
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56620
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4203
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The LynxPoint southbridge ACPI code needs the SSDT2 table to function
properly. Otherwise the ACPI evaluator in the kernel spews errors.
Change-Id: I73918545a07e43f4a281ff34d8537340d601b102
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56601
Reviewed-on: http://review.coreboot.org/4188
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Mainboards were defining their own SMBIOS type41
write function. Instead pull this into the generic
SMBIOS code and change the existing mainboards to
make use of it.
Change-Id: I3c8a95ca51fe2a3118dc8d1154011ccfed5fbcbc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56619
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4187
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A parrot device with a bad flash part has been seen to hang
in the elog_shrink code becuase the flash was not successfully
erased and it gets stuck in a loop trying to shrink the log
and then add an event.
Change-Id: I8bb13dbadd293f9d892f322e213c9255c8e9acb3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56405
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4186
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4185
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Only the first two DIMM SPDs are specified so far
- GPIO map is updated
- iSSD power sequencing removed
- USB port map updated
Change-Id: I4172460d3b075bfd5bb22013a6225cf0e8f95b9c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4184
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ssdt2 generation code was calling acpigen_patch_len().
However, none of the entries had AML object lengths that
needed patching. That resulted in the following message:
ASSERTION FAILED: file 'src/arch/x86/boot/acpigen.c', line 52
Additionally, this caused an errant write to a memory address
whose value was in the variable ltop. This was the 0 address.
Change-Id: I44abf5a4e4225220575aee6b5c9bb6b0be093a28
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56299
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ACPI code was defining two EHCI controllers and ignoring
the XHCI controller. This changes the second EHCI controller
to be XHCI instead and changes the wake resource to indicate
S3 and not S4.
cat /proc/acpi/wakeup
Device S-state Status Sysfs node
HDEF S4 *disabled pci:0000:00:1b.0
EHCI S3 *enabled pci:0000:00:1d.0
XHCI S3 *enabled pci:0000:00:14.0
Change-Id: If28775e6ef8608c22c85ca91d91d1f598ec7755d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56263
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4181
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The architecture name for our ARM port is armv7, not arm.
Hence, none of those flags were ever actually used.
Fix the architecture name and remove the flags, they should
not be set in xcompile, but in the Makefile, like in coreboot.
Change-Id: Id9c5db7ebceafddb58a1ce1988417f09c074ba6c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/56084
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4179
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable GPIO SMI for GPIO34 and set it as inverted so it
is only generated when it is raised by the EC.
1) ec console command: lidopen
2) wait until booted to developer screen
3) ec console command: lidclose
4) ensure system turns off
Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56052
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4177
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Restructure USB stack to not depend on PCI, and
make PCI stub available on x86, but provide fixed
BARs for ARM (Exynos 5)
Change-Id: Iee7c8b134c22b661a9a515e24943470c9dbadd1f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49970
Reviewed-on: http://review.coreboot.org/4175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Two structures in the USB EHCI stack were pointing
to hardware but not marked attribute((packed)) hence
leaving it to GCC to correctly align the data structures.
Next, the number of reserved bytes in hc_op_t was wrong
(but implicitly aligned to the correct values on x86)
It seems this worked fine on x86, but on ARM it was doing
the wrong thing.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I94bed4850ded7d3f7bbc7ff3079c103c6054c22d
Reviewed-on: https://gerrit.chromium.org/gerrit/55555
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4174
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The vendor ids were never updated to reflect LynxPoint's device
ids. Therefore, none of the initialization was being ran. Fix
this.
Change-Id: Ic6ec00c9fb1cbcb6087fd89b0acff3d83294ac6a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/55821
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4173
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to report whether coreboot enabled a SerialIO device
in ACPI mode we had been relying on reading NVS in the _STA
method for the SerialIO device.
The ACPI _STA method has restrictions on what it can access
and is unable to access OperationRegions outside its scope
which means it should not be trying to read NVS.
This change adds a new SSDT to the ACPI tables and fills it
with constants that indicate whether or not a device is enabled
in ACPI mode.
The ACPI code is changed to read these variables from the
SSDT and use that instead of trying to query a variable in NVS.
Attempt to use lpt-clk driver to probe the
device clocks for SerialIO devices and see that the kernel
does not complain about accessing the GNVS region.
Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These boards were returning 0 to indicate success when
the realmode handler expects it to return 1 to indicate
that it handled the interrupt.
Change-Id: I2baeaf8c2774fa7668a8b2f2d9ad698302eefb21
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50881
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4168
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are both pulled up to 3.3V in the schematic.
Change-Id: I12e055a39ff6100300c3d285899b8d6239e3773d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4164
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The update-fit command takes in a parameter for number of slots
in the FIT table. It then processes the microcobe blob in cbfs
adding those entries to the FIT table. However, the tracking of
the number of mircocode updates was incremented before validating
the update. Therefore, move the sanity checking before an increment
of the number of updates.
Change-Id: Ie8290f53316b251e500b88829fdcf9b5735c1b0e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50319
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4161
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order for the FIT entries to be populated in the table the
update-fit command needs to be done on the coreboot image. That
way the microcode entries are added to the table properly.
Change-Id: I44595aee1ca710f4f04d482d8900cf95fbc1797f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50317
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4159
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to probe the gpio-lynxpoint kernel driver the
LP GPIO controller needs to be exposed as a specific
ACPI device.
This also allows the resources to be exposed to the OS via
this device instead of the catch-all LPC device.
Ensure the driver loads at boot:
gpiochip_find_base: found new base at 162
gpiochip_add: registered GPIOs 162 to 255 on device: INT33C7:00
Also ensure the driver is visible in sysfs:
$ cat /sys/devices/platform/INT33C7:00/gpio/gpiochip162/label
INT33C7:00
Change-Id: I9f79c008f88da9b67ed1cdfdb9d3a581ce8f05ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50215
Reviewed-on: http://review.coreboot.org/4158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In the process of getting rid of compiler includes during in coreboot
and libpayload, we defined size_t and ssize_t ourselves, using a GCC
macro for size_t: __SIZE_TYPE__. Unfortunately, there is no
__SSIZE_TYPE__, so we temporarily redefine unsigned to signed to make
__SIZE_TYPE__ __SSIZE_TYPE__.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I4cf4eb0fdaa4db64277c2585fe2c1bdc0acdf02b
Reviewed-on: https://gerrit.chromium.org/gerrit/49947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4156
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
fill_lb_framebuffer() now sets the framebuffer pointer according to
the EDID information, so it must be called before setting the tag
and size.
(credit to rminnich for this, I'm just uploading it)
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I5ac783fa3a776eee504d39889284041d1dc2c92a
Reviewed-on: https://gerrit.chromium.org/gerrit/50012
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/4155
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that we have RW ramstage we don't need to have the
management engine lock down step done in a final SMM.
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PCI: 00:16.0: Disabling device
Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49757
Reviewed-on: http://review.coreboot.org/4153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There were two undefined MBP types that are now defined.
These include NFC status and some interesting timing data.
ME: Wake Event to ME Reset: 6 ms
ME: ME Reset to Platform Reset: 7 ms
ME: Platform Reset to CPU Reset: 51 ms
Change-Id: I67bf1f303f3c32497041e64c40eb9ccb6a63d88a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49756
Reviewed-on: http://review.coreboot.org/4152
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of having an OS re-parse cbmem book-keeping records
for the cbmem allocator just to get the console buffer export
the pointer to the memory console directly in a field named 'CBMC'.
This field lives in the GNVS table.
Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49764
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4149
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If elog_clear is called before other elog functions, for instance if it's
called through an SMI immediately after the system boots, then the elog data
structures won't have been set up and the system will go off the deep end.
This change adds a call to elog_init to elog_clear to make sure things things
are always initialized before we start using them.
Before this change, this command would cause
the system to lock up if run immediately after boot:
echo 1 > /sys/firmware/gsmi/clear_eventlog
After this change, that results in the log being cleared correctly.
Change-Id: I45027f0dbfa40ca8c581954a93b14b4fedce91ed
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49303
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4144
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Slight tweaks found when looking at latest ref code when
investigating package C-state issues.
A few bits in the clock gating register don't match the
documentation and are also cleaned up.
Change-Id: I36ced7280c160b114c70b2eeafc8b24813ff2f6a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49330
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4142
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The mainboard_interrupt_handlers() argument for the function
pointer was using void * as the type. This does not allow the compiler
to catch type differences for the arguments. Thus, some code has been
committed which violates the new interrupt callbacks not taking any
arguments. Make sure the compiler provides a type checking benefit.
Change-Id: Ie20699a368e70c33a9a9912e0fcd63f1e6bb4f18
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48970
Reviewed-on: http://review.coreboot.org/4141
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some handlers still had 2 variants, others were
incorrectly guarded by CONFIG_ variables. This
patch straightens them out.
This does not touch the siemens/sitemp_g1p1 which
provides an interestingly complex solution for the
int15 handler.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I5d74fdf7c2ab1faa96ebc2b5ca5c69398449b069
Reviewed-on: https://gerrit.chromium.org/gerrit/48979
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4140
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I3235f42c7faaf28a63455162ea55dc1a6bebd1f5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Hung-Te Lin <hungte@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/48290
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4128
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The EC saves its last "shutdown reason" for the system in EC RAM
that we can read back and log on boot.
The decode for the "reason" field will be added to mosys.
Change-Id: I834d39122e45262ef8e7ba59201accbee5857aac
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48323
Reviewed-by: David James <davidjames@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4127
Tested-by: build bot (Jenkins)
Commit b8ad224 changed the memory address in lb_cbmem_ref coreboot
table entries from a pointer to a uint64_t. This change was introduced
to make the cbmem utility work on both 32bit and 64bit userland.
Unfortunately, this broke the cbmem utility running on older versions
of coreboot because they were still providing a 32bit only field for
the address while the cbmem utility would now take the following 4
bytes as upper 32bits of a pointer that can obviously not be
mmapped. This change checks if the size of the lb_cbmem_ref structure
provided by coreboot is smaller than expected, and if so, ignore the
upper 32bit of the address read.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: If4c8e9b72b2a38c961c11d7071b728e61e5f1d18
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The format of this function changed but was not updated in
all mainboards. This fixes all Sandybridge/Ivybridge boards.
The int15 handler no longer takes a regs structure as an
argument and instead uses global variables. The yabel interface
is now similar enough that we can drop the duplicate handler.
Change-Id: Icdaae4d6d50884f6d7bce7a167d48cb1d4807010
Reviewed-on: https://gerrit.chromium.org/gerrit/48969
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4135
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This imports the cache/MMU code from coreboot as of 1877cee.
Change-Id: I97ec8b9640921a94a4b27d89e4ae6185e9f96f18
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/48288
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4134
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Recent commit proposal by Ron Minnich proposes to move to native gfx init for
qemu. Unfortunately we didn't have native init for default qemu video (cirrus)
Here is one extracted from GRUB one which I wrote couple of years ago.
Change-Id: Icb89cf918ef5d276bcc703c48c568e7b9c1be756
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Part of X201 port.
Change-Id: If17d707004aba9f08459dbd8f3a146fa3c076aa9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4052
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Per our discussions with Gerd, qemu will now always do native graphics
on coreboot. The VGA BIOS capability is not needed and will no longer
be supported. Attempts to build without native graphics will result in
an error.
This code builds for both x86 emulation targets. I'm hitting an issue
testing that is unrelated to coreboot; if someone can test, that
would be helpful. Be sure to start qemu with -vga std.
We also add a test for the PCI BAR being zero and return silently if it
is.
Change-Id: I66188f61e1bac7ad93c989cc10f3e0b55140e148
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4258
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Shawn Nematbakhsh