Certain Lexar USB disks may fail during the first calls to
get_descriptor(..., DT_CFG, ...) for unknown reasons. Therefore, make
several attempts before giving up.
BUG=chromium:466758
TEST=Manual on Samus. Go to recovery mode, verify that Lexar LJDS70 USB
stick is bootable.
BRANCH=None
Change-Id: I476ac22f9c4f844c60ebc6e53af8c144d70bb9d4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 93a0570b343479dd22506ad4d7961f0ea4251f8c
Original-Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Original-Change-Id: Ie581c7c71c53816065c7f59202581888a79e445e
Original-Reviewed-on: https://chromium-review.googlesource.com/302403
Original-Commit-Ready: Shawn N <shawnn@chromium.org>
Original-Tested-by: Shawn N <shawnn@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/12133
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If the device has already been disconnected then we shouldn't enable
host channel to start any transfer, otherwise this channel goes into
an odd state the channel is enabled but can not be disabled by set
hcchar.chdis=1. So we need check the device connect status before
enable channel.
BRANCH=None
BUG=chrome-os-partner:44534
TEST=None
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ae3e690b2cd4a9ea8b5766ac873b0e00bf3a23de
Original-Change-Id: Ib3ecf486649ca11b302144f9c00a5e88424e90fa
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/298402
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-(cherry picked from commit ea96f947b5304fdde2e0991d23febaeba209dde1)
Original-Reviewed-on: https://chromium-review.googlesource.com/299398
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Idf48ffbc4c2794900e09dec6b2e34e33b21f87b4
Reviewed-on: http://review.coreboot.org/11662
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
When disconnect is detected in dwc2_split_transfer() the split
configuration registers should be cleared before return.
BRANCH=None
BUG=chrome-os-partner:44534
TEST=On Jerry, usb hot plug works with devices behind hubs
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 37594d8b4490b6d393d19d17d8e497db7de8817d
Original-Change-Id: Ie1eecec067305874513c6ceb95df4240dc393cd6
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/295625
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-(cherry picked from commit d543e14cdc73bd549dd553c8d1d07672a1307981)
Original-Reviewed-on: https://chromium-review.googlesource.com/299700
Original-Commit-Ready: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Ib4604097743f2f9d763b29ee27f3bc1788a85a62
Reviewed-on: http://review.coreboot.org/11661
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Seems like our transferred bytes calculation for OUT transfers that span
more than one packet had been wrong, and we just got lucky that we never
noticed it before. The HCTSIZ.xfersize register field we're reading only
counts bytes transferred by the last packet we sent.
OUT endpoints cannot have short transfers -- every transfer should
either finish all bytes we wanted to send or end in a proper error
condition. Therefore, in the absence of an error we can just conclude
that all input bytes have been transferred.
BRANCH=veyron
BUG=chrome-os-partner:35525
TEST=SMSC95xx netboot on Jerry now works.
Change-Id: I57349e697c428df6b56e2f6f62e87652ef1e7a94
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Original-Commit-Id: 0abee13b6d89dec12c6fff581ece1836393c7703
Original-Change-Id: Id0a127e6919f5786ba05218277705dda1067b8c3
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/293956
Original-Reviewed-by: yunzhi li <lyz@rock-chips.com>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/11404
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Check device connect status while waiting for usb transfer complete
Avoid coreboot get stuck when usb device unplugged
BUG=chrome-os-partner:35525
TEST=None
BRANCH=None
Original-Change-Id: Id103501aa0d8b31b0b81bef773679c0fad79f689
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/292630
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/292966
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
Change-Id: I49396b74131dbfda505d9d3de5adbdc87eb92ce1
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-on: http://review.coreboot.org/11236
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The xhci_rh_port_status_changed() function tries to always clear all
port status bits, even though most of them don't interest us. This is
generally a smart thing to do since not clearing a status bit may cause
the controller to not generate any more Port Status Change Events.
However, the bitmask we currently use doesn't cover bit 23 (Port Config
Error Change) and instead covers bit 16 (Port Link State Write Strobe)
which is not really related to this and not a W1C bit. Probably a typo,
so let's fix that.
BRANCH=None
BUG=None
TEST=Plugged/unplugged a bunch of USB devices on an XHCI Falco.
Original-Change-Id: Ia83f5b72cce094859c0f0e730752d7b5cfa6e1c6
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/291842
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I11f5fe38cb70055daf6e866a8ee84ca80488e3bf
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11194
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The 1.1 revision of the XHCI specification added an extra 5 bits to the
Max Scratchpad Bufs field of HCSPARAMS2 that newer controllers make use
of. Not honoring these bits means we're not allocating as many
scratchpad buffers as the controller expects, which means it will
interpret some uninitialized values from the end of the pointer array as
scratchpad buffer pointers, which obviously doesn't end well. Let's fix
that.
BRANCH=none
BUG=chrome-os-partner:42279
TEST=Makes a USB-related memory corruption issue disappear.
Original-Change-Id: I7c907492339262bda31cdd2b5c0b588de7df8544
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/291681
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Iba1007bfebffe1f564f78bb875fff9ba0fe11a38
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11189
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If short packet detected, stop this transfer and return the actual
transferred size
BUG=chrome-os-partner:42817
TEST=Netboot could run well
BRANCH=None
Original-Change-Id: Icb4317f48aa04ac15bb1886b81d2e3c472d123d0
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/288215
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-(cherry picked from commit d372343b4e3d664ce2d76dbf55a5061b5d496bba)
Original-Reviewed-on: https://chromium-review.googlesource.com/291064
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Change-Id: I43d9edffe2074c037f2df203621863e54d2597fa
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-on: http://review.coreboot.org/11187
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch re-adds a few fixes that originally went into the
chromeos-2013.04 tree. I kinda seem to have slipped them into the
backport of Nico's original XHCI patch (crosreview.com/168097) instead
of making a new change, which was not very clever and caused them to be
forgotten in the later upstreaming wave.
Changing internal XHCI error numbers is just a cosmetic change to make
them uniquely identifyable in debug output. Bumping the timeout to 3
seconds is an actually important fix since we have seen mass storage
devices needing that much in the past.
BRANCH=None
BUG=None
TEST=Diffed payloads/libpayload/drivers/usb between chromeos-2013.04 and
chromeos-2015.07, confirmed that no serious differences remain.
Original-Change-Id: I03d865dbe536072d23374a49a0136e9f28568f8e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/290423
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I5d773d3a23683fb2164916cc046f4a711b8d259e
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/11178
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Before the controller's destroy_device() could interrogate
the usbdev_t object usb_detach_device() was freeing and
NULLing out the pointer. That results in all callers who
needed that object to start accessing random bits of memory.
This eventually led into free()ing memory it shouldn't which
corrupted the allocator's state. Eventually, all forward
progress was lost by way of a single ended linked list
turning into a circular list.
The culprit seems to be a bad merge in commit e00ba21.
BUG=chrome-os-partner:43419
BRANCH=None
TEST=Can boot into OS now w/o "hanging" on glados.
Original-Change-Id: I86dcaa1dbaf112ac6782e90dad40f0932f273a1f
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/290048
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9135eb0f798bf7dbeccc7a033c3f8471720a0de5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11173
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch adds support for the SuperSpeed half of USB 3.0 hubs, which
previously prevented SuperSpeed devices behind those hubs from working.
BRANCH=None
BUG=chrome-os-partner:39877
TEST=Played around with multiple hubs and devices on Oak and Falco, can
no longer find a combination that doesn't work.
Change-Id: I20815be95769e33d399b7ad91c3020687234e059
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3db96ece20d2304e7f6f6aa333cf114037c48a3e
Original-Change-Id: I2dd6c9c3607a24a7d78c308911e3d254d5f8d91d
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/284577
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: chunfeng yun <chunfeng.yun@mediatek.com>
Reviewed-on: http://review.coreboot.org/10958
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We have been trying to avoid reassigning previously used USB addresses
to different devices since CL:197420, because some devices seem to take
issue with that. Unfortunately, that patch doesn't affect XHCI: those
controllers insist on chosing addresses on their own. The only way to
prevent them from reusing a previously assigned address is to not
disable that slot at all.
This patch implements address reuse avoidance on XHCI by not disabling
slots when a device is detatched (which may occur both on physical
detachment or if we simply couldn't find a driver for that device).
Instead, we just release as many resources as we can for detached
devices (by dropping all endpoint contexts) and defer the final cleanup
until the point where the controller actually runs out of resources (a
point that we probably don't often reach in most firmware scenarios).
BRANCH=none
BUG=chrome-os-partner:42181
TEST=Booted an Oak plugged into a Servo without having a driver for the
SMSC network chip, observed that it could still enumerate the next
device afterwards. Kept unplugging/replugging stuff until the cleanup
triggered and made sure the controller still worked after that. Also
played around a bit on a Falco without issues.
Change-Id: Idfbab39abbc5bc5eff822bedf9c8d5bd4cad8cd2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 88c6bcbc41156729c3c38937c8a4adebc66f1ccb
Original-Change-Id: I0653a4f6a02c02498210a70ffdda9d986592813b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/284175
Original-Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10957
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With split transaction, dwc2 host controller can handle full- and
low-speed devices on hub in high-speed mode. This commit adds support
for split control and interrupt transfers
BUG=None
TEST=Connect usb keyboard through hub, usb keyboard can work
BRANCH=None
Change-Id: If7a00db21c8ad4c635f39581382b877603075d1a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4fb514b7f7f7e414fa94bfce05420957b1c57019
Original-Change-Id: I07e64064c6182d33905ae4efb13712645de7cf93
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/283282
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/10956
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
dwc2 host core do not have a periodic schedule list, so try to send
an interrupt packet in poll_intr_queue() function and use frame
number read from usb core register to calculate time and schedule
transfers.
BUG=None
TEST=Tested on RK3288 with two USB keyboards(connect to SoC without
USB hub), both work correctly.
BRANCH=None
Change-Id: I16f7977c45a84b37c32b7c495ca78ad76be9f0ce
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3d0206b86634bcfdbe03da3e2c8adf186470e157
Original-Change-Id: Ie54699162ef799f4d3d2a0abf850dbeb62417777
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/280750
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: http://review.coreboot.org/10774
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This will make the code work with the different styles
of Kconfig (emit unset bools vs don't emit unset bools)
Roughly, the patch does this, and a little bit of fixing up:
perl -pi -e 's,ifdef (CONFIG_LP_.+?)\b,if IS_ENABLED\($1\),g' `find . -name *.[ch]`
perl -pi -e 's,ifndef (CONFIG_LP_.+?)\b,if !IS_ENABLED\($1\),g' `find . -name *.[ch]`
Change-Id: Ib8a839b056a1f806a8597052e1b571ea3d18a79f
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10711
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Found in rockchips rk3288 as used in google/veyron.
BUG=None
TEST=None
BRANCH=None
Change-Id: I2f2c36c5bea3986a8a37f84c75608b838a8782ae
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 59a0bcd97e8d0f5ce5ac1301910e11b01e2d24b1
Original-Change-Id: Ic89ed54c48d6f9ce125a93caf96471abc6e8cd9d
Original-Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/272108
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Lin Huang <hl@rock-chips.com>
Original-Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: http://review.coreboot.org/10689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
1. There is a mis-understanding to calculate the value of TD Size
in Normal TRB. For MTK's xHCI controller it defines a number of
packets that remain to be transferred for a TD after processing
all Max packets in all previous TRBs, that means don't include the
current TRB's.
2. To minimize the scheduling effort for synchronous endpoints in xHC,
the MTK architecture defines some extra SW scheduling parameters for
HW. According to these parameters provided by SW, the xHC can easily
decide whether a synchronous endpoint should be scheduled in a specific
uFrame. The extra SW scheduling parameters are put into reserved DWs
in Slot and Endpoint Context. But in coreboot synchronous transfer can
be ignored, so only two fields are set to a default value 1 to support
bulk and interrupt transfers, and others are set to zero.
3. For control transfer, it is better to read back doorbell register or add
a memory barrier after ringing the doorbell to flush posted write.
Otherwise the first command will be aborted on MTK's xHCI controller.
4. Before send commands to a port, the Port Power in PORTSC register should
be set to 1 on MTK's xHCI so a hook function of enable_port in
generic_hub_ops_t struct is provided.
Change-Id: Ie8878b50c048907ebf939b3f6657535a54877fde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 738609c11f16264c6e6429d478b2040cb391fe41
Original-Change-Id: Id9156892699e2e42a166c77fbf6690049abe953b
Original-Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/265362
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: http://review.coreboot.org/10389
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
BRANCH=none
BUG=none
TEST=none
Change-Id: I563ef65db900d7675aeb5b9123dfb5a8980bf964
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9764115d7bcce1d6423464bd81b58211ac728409
Original-Change-Id: Ibac8d3b9e28b4a563079f288901abcfbff6913ee
Original-Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/269863
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Queue: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: http://review.coreboot.org/10388
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
The EHCI driver never looked for the base address handed to
it but instead used an uninitialized field for that information.
Change-Id: I89fe0cc212092672b36e978083e3de78419b1eb5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/10179
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Make the XHCI driver compile on ARM again. The Panther Point
specific shutdown handler is certainly _not_ necessary there.
Change-Id: I470afd4d82d101902b119b3ead4381e2b36a94b0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10091
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Since CL:170664, all SC_SPEED_XXX renamed to SC_SPEED1_XXX.
There is one missing in xhci_dump_slotctx() function which makes
compilation error.
BUG=none
TEST=enable USB_DEBUG and XHCI_DUMPS macros in xhci_private.h;
then emerge-auron libpayload
Change-Id: Ib96805cb7fc1cad17b205277539fb2120632f6f4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3ca0174e93ad131309ad07187c95c1e84c7d4fc5
Original-Change-Id: Id056b4684831a5717e87969e95ab17f11db29696
Original-Reviewed-on: https://chromium-review.googlesource.com/261414
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Harry Pan <harry.pan@intel.com>
Original-Tested-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: http://review.coreboot.org/9877
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The address of the output buffer sent to the device should be
the bus address and not the virtual address.
BUG=chrome-os-partner:31438
TEST=tested on Pistachio FPGA and bring up board;
USB works properly after this change
BRANCH=none
Change-Id: I5c9d199e17c3f4303095ad73f4980d32d04c6118
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 942c385c112c2a4e409da806548081d3e2f8f438
Original-Change-Id: I0c06196501a968a72cb3f2c7dd1027bb22cdaada
Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/245387
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9455
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Total FIFO length is split into 512 byte blocks.
Allocate these blocks to GRXFSIZ and GNPTXFSZ evenly.
This method avoids hardcoding and makes the FIFO size value
work for dwc2 controllers that have a different FIFO ram size.
BUG=chrome-os-partner:32634
BRANCH=None
TEST=Boot kernel from USB
Change-Id: I78ce0fa4c4600fb56c991874a93bdd6674e648c2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5645a25e95f84359cd10fc9fcf56e1f73fd6ce87
Original-Change-Id: Ib50a08c193f7f65392810ca3528a97554f2c3999
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/233119
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9454
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
BUG=chrome-os-partner:29778
TEST=emerge-veyron libpayload
Change-Id: I33f312a939e600b8f4e50a092bb61c5d6bc6d741
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 39ffe53336a2a3b2baa067cdd3dccca5ae93f68e
Original-Change-Id: Idad1ad165fd44df635a0cb13bfec6fada1378bc8
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/211053
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9453
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Don't attempt to scan the PCI bus if the bridge is disabled. When
the PCI bridge is not setup and enabled, it is possible for the
secondary bus register to contain the value zero (0). In this case
the usb_scan_pci_bus routine gets into an infinite recursive loop
which ends only when the heap or stack is exhausted. This patch
verifies that the PCI bridge is enabled by verifying that it is
enabled for either memory or I/O operations. When enabled, the
secondary bus is scanned.
BRANCH=none
BUG=None
TEST=Build and run on Samus
Change-Id: I6826dc1d73b7c24729de5ac7c4d3534922ca73c5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 63d04b47934761351b54c847a2692bdef81ce54f
Original-Change-Id: I855240c52fa3eba841e6754816ebbcb824abc4cd
Original-Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/236382
Original-Commit-Queue: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Tested-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/8734
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If a TD is comprised of one or more Normal TRBs and terminated with an
Event Data TRB, then the transition to the Idle state (and associated
Stream state save) could occur after all the data for the TD has been
moved (e.g. after Transfer Event TRBs have been executed), but before the
Event Data TRB is executed. Under these conditions, the execution of the
Event Data TRB is necessary to complete the TD, otherwise it does not
occur until the next time the Stream is scheduled. This could lead to the
lock up.
The Evaluate Next TRB(ENT) flag provides a means of forcing the execution
of a terminating Event Data TRB. Setting ENT flag in last Normal TRB makes
the xHC to evaluate the Even Data TRB.
BUG=chrome-os-partner:29375
TEST=Verified kernel boot-up on storm from previously failing USB stick.
USB stick model: Sandisk Ultra USB 3.0 Pen Drive 32 GB
Strontium Jet USB 3.0 Pen Drive 32 GB
Change-Id: I092e2109c55c2274239c493cb67b47d730304ed2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7eefb3b2858c841165ae839d349d2a0be50fbcc8
Original-Change-Id: I4e123577ec5a5996d87d2fc52cb6cf5c571c9fae
Original-Signed-off-by: Sourabh Banerjee <sbanerje@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/220123
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/8736
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If EHCI controller has TT (Transaction Translator) support in
root-hub, then we need to keep control over this controller when
USB keyboard (low-speed device) is connected to root-hub port.
Need to add "CONFIG_LP_USB_EHCI_HOSTPC_ROOT_HUB_TT=y" to config file
(e.g. payloads/libpayload/configs/config.nyan_big) to support this
feature.
BUG=chrome-os-partner:32355
TEST=Tested on nyan_big platform.
Press ESC+REFRESH+POWER keys on internal keyboard to power up.
Press Left Arrow or Right Arrow on USB keyboard to switch between
"English" and "Default Locale" in coreboot UI. Or unplug and plug
in device and try again.
Root hub <- low-speed USB keyboard
Root hub <- full-speed hub <- low-speed USB keyboard
Root hub <- high-speed hub <- low-speed USB keyboard
Change-Id: Iaa2823f64c8769fc808ee7a316c378f18f004e63
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4ad57fd673d6dc8814fe99a4ac420566bb17e77b
Original-Change-Id: Id86a289bc587653b85227c1d50f7a4f476f37983
Original-Signed-off-by: Jim Lin <jilin@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/220125
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Chapter 3.1 "Periodic Frame List" of EHCI 1.0 specification says
"Frame List Link pointers always reference memory objects that are
32-byte aligned."
jwerner@chromium.org suggests setting it to be 64-byte aligned for
consistency with other EHCI queue structures.
BUG=chrome-os-partner:31993
TEST=Tested on nyan platform. Before adding patch, USB keyboard behind
an external hub is not working to switch between "Default Locale" and
"English" (after pressing ESC+REFRESH+POWER on embedded keyboard and
later Left/Right-Arrow key on USB keyboard).
Change-Id: Ie6259f2df20ae2618c2074e831fad087f227091d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 23fc02e6ba3b17be4eaf18810ec6fc0d9c0e0b9a
Original-Change-Id: If52ddc43ebd5d509c19f104928dced5bd09b1706
Original-Signed-off-by: Jim Lin <jilin@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/218403
Original-Reviewed-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8738
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Data toggle should be running like 0, 1, 0, 1, ...
In the failed case (where a low-speed USB keyboard or km232 device
is installed), data toggle will be running as 0, 1, 0, 1, ..., 1, 1.
Therefore causing Halted or Transaction Error bit to be set in qTD
Status field.
BUG=None
BRANCH=None
TEST=Tested on nyan_kitty platform, firmware-kitty-5771.61.B branch.
Attached USB keyboard or km232 device to root-hub port (same side as
SD card slot).
Made sure no transaction error after doing interrupt transfer.
Change-Id: I576f3c583dae4c279a6e0e8ffdfce5abe463277d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 64b0428aaab869e20f6720669e953acf82ecb846
Original-Change-Id: Ic2c0f95cff2ae6e314967b0b82231a962255f1a7
Original-Signed-off-by: Jim Lin <jilin@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/233857
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/8747
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some USB sticks seem to send a NAK at a place where they mustn't
by spec, leading to a controller side error condition.
To avoid it, wait a millisecond which is enough to get past the
NAK condition. That delay only happens on device discovery so it
won't affect boot time by more than 1ms per device.
BUG=chromium:414959
BRANCH=none
TEST=depthcharge recognizes a Lexar 16GB USB stick after applying
this change.
Change-Id: I0e385702a5259b16fda0a253fc121d8f66e6705c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 10bbfda8395af009e7f910cc503f50c2ad969ae8
Original-Change-Id: I6dd5ca34e9f3767003ccb0ca9daaf16116f4a2df
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/228791
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Sheng-liang Song <ssl@chromium.org>
Reviewed-on: http://review.coreboot.org/8735
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
EHCI driver accesses mmio space using regular struct pointers. In order to avoid
any CPU re-ordering, memory barrier is required in async_set_schedule,
especially for arm64. Without the memory barrier, there seems to be re-ordering
taking place which leads to USB errors with some flash drives as well as
transfer errors in netboot.
BUG=chrome-os-partner:31533
BRANCH=None
TEST=With the memory barrier introduced, netboot for ryu completes transfer
without any error and finishes within 6-7 seconds.
Change-Id: Ib6d29dc79fd5722c27284478e8da316929e86bff
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 561bdd746c4d4446ce0a6d21337d354625d85ddc
Original-Change-Id: Ic05d47422312a1cddbebe3180f4f159853604440
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/213917
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
Original-Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/8732
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
`di` points to a single item in xhci->dev[], which is malloc'd
collectively. Trying to free() leads to pain.
Change-Id: Ibd99eda905d43cbf2d2c111dfd0186ed6b119329
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Found-by: Coverity Scan
Reviewed-on: http://review.coreboot.org/8515
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Test for devno != -1 before trying to access array[devno]
(which may be array[-1]).
Change-Id: Ia69cc7eba0335f02bb0efec003a320a3c0646acb
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Found-by: Coverity Scan
Reviewed-on: http://review.coreboot.org/8509
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With commands typically shorter than the buffer they're
copied to, copy cmdlen bytes, cut off by the buffer limit.
Change-Id: Ia9d2663bd145eff4538084ac1ef8850cfbcea924
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Found-by: Coverity Scan
Reviewed-on: http://review.coreboot.org/7977
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Fix pointer related casts since this can create a problem for 64-bit systems.
BUG=None
BRANCH=None
TEST=Compiled successfully for link, nyan using emerge-* libpayload
Original-Change-Id: I4cbd2d9f1efaaac87c3eba69204337fd6893ed66
Original-Reviewed-on: https://chromium-review.googlesource.com/199564
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
(cherry picked from commit 914b118a64b0691aeca463dff24252db9c24109e)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I11f070ed5d3eddd8b9be30c428cb24c8439e617b
Reviewed-on: http://review.coreboot.org/7905
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
xHCI Spec says TD Size (5 bits) field shall be forced to 31,
if the number of packets to be scheduled is greater than 31.
BUG=chrome-os-partner:27837
BRANCH=rambi,nyan
TEST=Manual: Ensure recovery boot with USB 2.0 media on Squawks
works fine without any babble errors.
Original-Change-Id: Iff14000e2a0ca1b28c49d0da921dbb2a350a1bbd
Original-Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Original-Originally-Reviewed-on: https://chromium-review.googlesource.com/202297
Original-Reviewed-on: https://chromium-review.googlesource.com/202330
Original-Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Tested-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit ae58b99370df3a86bf15d84b97db858a968b1dbd)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I9668b947f676c109fad9297e5efde91bf7f796fd
Reviewed-on: http://review.coreboot.org/7913
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
There were a few build warnings in the USB driver to clean
up before -Werror may be enabled.
Change-Id: I220cfcf0ee926912a184a91d3ced3ba61259130e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/7921
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
I always thought the support for multiple logical SCSI units in the USB
mass storage class was a dead feature. Turns out that it's actually used
by SD card readers that provide multiple slots (e.g. one regular sized
and one micro-SD). Implementing perfect support for that would require a
major redesign of the whole MSC stack, since the one device -> one disk
assumption is deeply embedded in our data structures.
Instead, this patch implements a poor man's LUN support that will just
cycle through all available LUNs (in multiple calls to usb_msc_poll())
until it finds a connected device. This should be reasonable enough to
allow these card readers to be usable while only requiring superficial
changes.
Also removes the unused 'protocol' attribute of usb_msc_inst_t.
BRANCH=rambi?,nyan
BUG=chrome-os-partner:28437
TEST=Alternatively plug an SD or micro-SD card (or both) into my card
reader, confirm that one of them is correctly detected at all times.
Original-Change-Id: I3df4ca88afe2dcf7928b823aa2a73c2b0f599cf2
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/198101
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 960534a20e4334772c29355bb0d310b3f41b31ee)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I39909fc96e32c9a5d76651d91c2b5c16c89ace9e
Reviewed-on: http://review.coreboot.org/7904
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
So I was debugging this faulty USB SD card reader that would just fail
it's REQUEST SENSE response for some reason (sending the CSW immediately
without the data), cursing those damn device vendors for building
non-compliant crap like I always do... when I noticed that we do not
actually set the Allocation Length field in our REQUEST SENSE command
block at all! We set a length in the CBW, but the SCSI command still has
its own length field and the SCSI spec specifically says that the device
has to return the exact amount of bytes listed there (even if it's 0). I
don't know what's more suprising: that we had such a blatant bug in this
stack for so long, or that this card reader is really the first device
to actually be spec compliant in that regard.
This patch fixes the bug and changes the command block structures to be
a little easier to read (why that field was called 'lun' before is
beyond me... LUN is a transport level thing and should never appear in
the command block at all, for any command). It also fixes a memcpy() in
wrap_cbw() to avoid a read buffer overflow that might expose stack frame
data to the device.
BRANCH=rambi?,nyan
BUG=chrome-os-partner:28437
TEST=The card reader works now (for it's first LUN at least).
Original-Change-Id: I86fdcae2ea4d2e2939e3676d31d8b6a4e797873b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/198100
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 88943d9715994a14c50e74170f2453cceca0983b)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I3097c223248c07c866a33d4ab8f3db1a7082a815
Reviewed-on: http://review.coreboot.org/7903
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We recently changed the USB stack to detach devices aggressively that we
don't intend to use. This alone is not really a problem, but it
exarcerbates the fact that our device detachment itself is not very
good. We destroy any local info about the device, but we don't properly
disable the offending port. The device keeps thinking that it's active,
and if we later try to reuse that device address for another device
things become confused.
The real fix would be to properly disable all ports that we don't intend
to use. Unfortunately, this isn't really possible in our current
device/hub polymorphism structure, and I don't want to hack a new
disable_port() callback into usbdev_t that really doesn't belong there.
We will only be able to fix this cleanly after we ported all root hubs
to the generic_hub interface.
Until then, an easy workaround is to just avoid reusing addresses as
long as possible. This is firmware, so the chance that we'll ever run
through 127 devices is really small in practice. Even if we ever fix the
underlying issue, it's probably a smart precaution to keep.
BRANCH=nyan,rambi
BUG=chrome-os-partner:28328
TEST=Boot from a hub that has an "unknown" device in an earlier port
than the stick you want to boot from, make sure you can still boot.
Original-Change-Id: I9b522dd8cbcd441e8c3b8781fcecd2effa0f23ee
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/197420
Original-Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 28b48aa69b55a983226edf2ea616f33cd4b959e2)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Id4c5c92e75d6b5a7e8f0ee3e396c69c4efd13176
Reviewed-on: http://review.coreboot.org/7881
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
If a payload decides not to use a USB device then the device can be
detached. This prevents the device from interfering with normal
operation on some platforms. Also, it aligns the behavior of
usb_generic_init with class-specific init functions such as
usb_msc_init, which will detach unsupported devices.
BUG=None
TEST=Manual on Squawks. Test recovery boot w/ USB 2.0 media, verify
that media boots and no babble error is encountered.
BRANCH=rambi
Change-Id: I8fb30951d273e4144cda214a30a2e86df90f2c1c
Original-Change-Id: Iee522344558749603defb2966e18765aa195dae2
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/195401
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit f7778ace68c9bee8dfab2b263e5dd054fc50c3bb)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/7830
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We've recently fixed a problem where an external hard drive would choke
due to one too many CLEAR_FEATURE(HALT) commands in the XHCI stack with
"libpayload: usb: xhci: Fix STALL endpoint handling". Clearing stall
conditions from within the transfer function is wrong in general... this
is really something that is host controller agnostic and should be left
to the higher-level driver to decide. The mass storage driver (the only
one that should really encounter stalls right now) already contains the
proper amount of clear_stall() calls... any more than that is redundant
and as we found out potentially dangerous.
This patch removes automatic clear stalls from UHCI and OHCI drivers as
well to make things consistent between host controllers.
BUG=chromium:192866
TEST=None. I could borrow the original hard drive from Shawn and compile
a Snow to only use the OHCI driver to reproduce/verify this, but alas, I
am lazy (and it's really not that important).
Original-Change-Id: Ie1e4d4d2d70fa4abf8b4dabd33b10d6d4012048a
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/193732
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit d46e183f3e7e0b0130becdefa6fd3ef8097df54b)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ie8f4ab3db8ec0d9a2d1e91c62967833e59c46700
Reviewed-on: http://review.coreboot.org/7223
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This patch combines a few minor fixes and refactoring to the various
host controller and root hub drivers to ensure they all do the right
thing on a call to usb_exit(). It puts a usb_detach_device(0) call
into detach_controller() so that the HCD doesn't need to remember to
tear down the root hub itself, and makes sure all root hubs properly
detach the subtree of devices connected to their ports first (as
generic_hub and by extension XHCI had already been doing).
It also fixes up some missing free() calls and replaces most 'ptr =
malloc(); if (!ptr) fatal()' idioms with the new x(z)alloc().
BUG=chromium:343415
TEST=Tested EHCI on Big and OHCI, EHCI, and XHCI on Snow. Could not test
UHCI (unless anyone volunteers to port coreboot to a ZGB? ;) ), but the
changes are really tame.
Original-Change-Id: I6eca51ff2685d0946fe4267ad7d3ec48ad7fc510
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/193731
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 5791b546e5a21a360d0c65888a5b92d5f48f8178)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I00138f0aeceb12ed721f7368c7788c9b6bee227d
Reviewed-on: http://review.coreboot.org/7222
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This patch adds the 10ms TRSTRCY delay between a reset and the following
Set Address command that is required by the USB 2.0 specification to the
EHCI root hub driver. The generic_hub driver that's used for XHCI and
external hubs already included this delay. This is such a glaring
violation of the spec that I'm really amazed how many USB 2.0 devices
we tested before seemed perfectly fine with responding to a Set Address
within 2 microframes of the reset...
It also increases the port reset hold delay by one millisecond to avoid
an ugly race condition on Tegra SoCs: they decided to time the 50ms
themselves instead of relying on the CPU to do it (fair enough), and to
automatically transition Port Reset to 0 and Port Enable to 1 after that
(bad idea). If the CPU's read-modify-write to clear Port Reset races
exactly with the host controller setting Port Enable, we may end up
clearing the bit again and going into the companion controller handoff
path later on. The added millisecond shouldn't cause any problems for
other host controllers and is not a big deal compared to other delays in
this code path.
BUG=chrome-os-partner:26749
TEST=Run several dozen reboot loops with The USB Stick of Death (TM) (a
blue Patriot XT 13fe:5200 with bcdDevice = 1.00), make sure it always
gets detected correctly.
Original-Change-Id: Idd3329ae6d7e5e1c07a84a5475549b3459836b31
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/189872
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Reviewed-by: Jim Lin <jilin@nvidia.com>
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
(cherry picked from commit 4deca38e9d79f6373f4418fcaf51a6945232c8b8)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I68a29bfd2e0f30409fbfc330b2575f0f9f61a79d
Reviewed-on: http://review.coreboot.org/7221
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch enables the OHCI driver to use DMA memory, which is necessary
for ARM systems where DMA devices are not cache coherent. I really only
need this to test some later OHCI changes, but it was easy enough...
copied almost verbatim from ehci.c.
Change-Id: Ia717eef28340bd6182a6782e83bfdd0693cf0db1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/193730
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit e46b6ebc439e86a00e13bf656d60cf6c186a3777)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7010
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Remove the call to clear_stall in xhci_reset_endpoint because we will
call clear_stall from the mass-storage driver.
- Remove the xhci_reset_endpoint call from xhci_bulk on STALL since we
will reset on the next transfer anyway.
- Remove the clear_halt parameter from xhci_bulk since it's now unused.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I852b87621861109e596ec24b78a8f036d796ff14
Reviewed-on: https://chromium-review.googlesource.com/192866
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit e67e4f0545cbdc074328c83c7edccf9e712cd7be)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7011
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
If a port is connected before and after an xhci controller reset, the
PORTSC CSC bit may not be asserted. Add an additional check in
xhci_rh_port_status_changed for the PRC bit so we can correctly handle
ports in such a state.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Change-Id: I2d623aae647ab13711badd7211ab467afdc69548
Reviewed-on: https://chromium-review.googlesource.com/189394
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit ee7c3ea182b35bb6ce3c62f301c4515714f6e654)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7002
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The generic roothub reset port function is overly broad and does some
things which may be undesirable, such as issuing multiple resets to a
port if the reset is deemed to have finished too quickly. Remove the
generic function and replace it with a controller-specific function,
currently only implemented for xhci.
Change-Id: Id46f73ea3341d4d01d2b517c6bf687402022d272
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/189495
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 54e1da075b0106b0a1f736641fa52c39401d349d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/7001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Forgot an asterisk and everything goes to hell. Sorry about that.
Change-Id: I6b2503ca3ea0f80d4e4e5d8b8c0e986fec5db2c9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173587
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: David James <davidjames@chromium.org>
(cherry picked from commit 2a357560a697b56cc6022a4dd3dda47b33568d83)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The dump_td() debug function in the EHCI stack incorrectly masks the
amount of transferred bytes on output... the actual field is 15 bits
wide (30:16). Let's just use the mask constant we already have for all
the other code.
Change-Id: I28c6f0ec75cc613e38d53b670645d19bf9ffe1b9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174986
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 570077da7f16bbe2204b4a80790e4bd8fe1a2bd7)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6853
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch represents a major overhaul of the USB enumeration code in
order to make it cleaner and much more robust to weird or malicious
devices. The main improvement is that it correctly parses the USB
descriptors even if there are unknown descriptors interspersed within,
which is perfectly legal and in particular present on all SuperSpeed
devices (due to the SuperSpeed Endpoint Companion Descriptor).
In addition, it gets rid of the really whacky and special cased
get_descriptor() function, which would read every descriptor twice
whether it made sense or not. The new code makes the callers allocate
descriptor memory and only read stuff twice when it's really necessary
(i.e. the device and configuration descriptors).
Finally, it also moves some more responsibilities into the
controller-specific set_address() function in order to make sure things
are initialized at the same stage for all controllers. In the new model
it initializes the device entry (which zeroes the endpoint array), sets
up endpoint 0 (including MPS), sets the device address and finally
returns the whole usbdev_t structure with that address correctly set.
Note that this should make SuperSpeed devices work, but SuperSpeed hubs
are a wholly different story and would require a custom hub driver
(since the hub descriptor and port status formats are different for USB
3.0 ports, and the whole issue about the same hub showing up as two
different devices on two different ports might present additional
challenges). The stack currently just issues a warning and refuses to
initialize this part of the hub, which means that 3.0 devices connected
through a 3.0 hub may not work correctly.
Change-Id: Ie0b82dca23b7a750658ccc1a85f9daae5fbc20e1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170666
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit ecec80e062f7efe32a9a17479dcf8cb678a4a98b)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6780
Tested-by: build bot (Jenkins)
This patch removes the confusing concept of a special "xhci_speed" with
a different numeric value from the usual speed used throughout the USB
core (except for the places directly interacting with the xHC, which are
explicitly marked). It also moves the MPS0 decoding function into the
core and moves some definitions around in preparation of later changes
that will make the stack SuperSpeed-ready. It makes both set_address
implementations share a constant for the specification-defined
SetAddress() recovery delay and removes pointless additional delays from
the non-XHCI version.
Change-Id: I422379d05d4a502b12dae183504e5231add5466a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170664
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald Minnich <rminnich@chromium.org>
(cherry picked from commit f160d4439c0d7cea1d2e6b97207935d61dcbb2f2)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6776
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch fixes a bug in the XHCI stack that occurs when a multi-TRB TD
times out before the last TRB is processed. The driver will correctly
issue a Stop Endpoint command in that case, but the xHC will still
preserve the transfer state and just pick up right after that on the
next doorbell ring. It will then process the leftover TRBs from the old
TD the next time a transfer is issued. (cf. XHCI 4.6.9)
We fix this by changing the existing xhci_reset_endpoint() calls in
transfer functions to not only trigger on Halted (2) and Error (4), but
also on Stopped (3). That function will not actually issue a Reset
Endpoint command in this case, but it will nuke the whole transfer ring
and issue a Set TR Dequeue Pointer command, which is sufficient (though
slightly overkill) to solve our problem.
Change-Id: I3abbe30ff9d4911a8af1f792324e018d427019e8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170833
Reviewed-by: Ronald Minnich <rminnich@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit f12424af0e29ac12963e8e5a7970fadcc0bb6cee)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6787
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The existing USB_MEMORY mechanism to instantiate non-PCI host
controllers is clunky and inflexible... most importantly, it doesn't
allow multiple host controllers of the same kind. This patch replaces it
with a function that allows payloads to directly instantiate as many
host controllers of whatever type they need.
Change-Id: Ic21d2016a4ef92c67fa420bdc0f0d8a6508b69e5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169454
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit b6e95c39dd91f654f0a345f17b3196f56adf4891)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6644
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch fixes the following minor bugs in the USB stack:
1. Ensure that all dynamically allocated device structures are cleaned
on detachment, and that the device address is correctly released again.
2. Make sure MSC and HID drivers notice missing endpoints and actually
detach the device in that case (to prevent it from being used).
3. Make sure XHCI-specific set_address() cleans up all data structures
on failure.
4. Fix broken Slot ID range check that prevented XHCI devices from being
correctly cleaned up.
Change-Id: I7b2b9c8cd6c5e93cb19abcf01425bcd85d2e1f22
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170665
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald Minnich <rminnich@chromium.org>
Tested-by: Ronald Minnich <rminnich@chromium.org>
(cherry picked from commit 9671472263ddd0c30400ae3b6da780a18cd21ded)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6701
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The USB MSC device structure contains a "ready" state that can be either
"ready", "not ready" or "detached". The last one can only be assigned
when the device is completely unresponsive and gets forcefully logically
detached via usb_detach_device(). This call (at least in the current
version) also calls all destructors and frees the complete usbdev_t
structure (including the MSC specific part), which unfortunately makes
storing the "detached" state in that very structure a little pointless.
This patch reduces the "ready" value to a simple boolean and makes sure
that all detachment cases immediately return from the MSC driver,
carefully avoiding any use-after-free opportunities.
Change-Id: Iff1c0849f9ce7c95d399bb9a1a0a94469951194d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170667
(cherry picked from commit fd4529f37fdd1c93a8b902488ffeef7001b1a05a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6654
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This patch updates the libpayload XHCI stack to run on ARM CPUs (tested
with the DWC3 controller on an Exynos5420). Firstly, it adds support for
64-byte Slot/Endpoint Context sizes. Since the existing context handling
code represented the whole device context as a C struct (whose size has
to be known at compile time), it was necessary to refactor the input and
device context structures to consist of pointers to the actual contexts
instead.
Secondly, it moves all data structures that the xHC accesses through DMA
to cache-coherent memory. With a similar rationale as in the ARM patches
for EHCI, using explicit cache maintenance functions to correctly handle
the actual transfer buffers in all cases is presumably impossible.
Instead this patch also chooses to create a DMA bounce buffer in the
XHCI stack where transfer buffers which are not already cache-coherent
will be copied to/from.
Change-Id: I14e82fffb43b4d52d687b65415f2e33920e088de
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169453
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit 1fa9964063cce6cbd87ba68334806dde8aa2354c)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6643
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch makes the EHCI driver work on ARM platforms which usually do
not support automatic cache snooping. It uses the new DMA memory
mechanism (which needs to be correctly set up in the Coreboot mainboard
code) to allocate all EHCI-internal communication structures in
cache-coherent memory, and cleans/invalidates the externally supplied
transfer buffers in Bulk and Control functions with explicit calls as
necessary.
Old-Change-Id: Ie8a62545d905b7a4fdd2a56b9405774be69779e5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167339
(cherry picked from commit 322338934add36a5372ffe7d2a45e61a4fdd4a54)
libpayload: ehci: Cache management is hard, let's go copying...
It turns out that my previous commit to make the EHCI stack cache aware
on ARM devices wasn't quite correct, and the problem is actually much
trickier than I thought. After having some fun with more weird transfer
problems that appear/disappear based on stack alignment, this is my
current worst-case threat model that any cache managing implementation
would need to handle correctly:
Some upper layer calls ehci_bulk() with a transfer buffer on its stack.
Due to stack alignment, it happens to start just at the top of a cache
line, so up to 64 - 4 bytes of ehci_bulk's stack will share that line.
ehci_bulk() calls dcache_clean() and initializes the USB transfer.
Between that point and the call to dcache_invalidate() at the end of
ehci_bulk(), any access to the stack variables in that cache line (even
a speculative prefetch) will refetch the line into the cache. Afterwards
any other access to a random memory location that just happens to get
aliased to the same cache line may evict it again, causing the processor
to write out stale data to the transfer buffer and possibly overwrite
data that has already been received over USB.
In short, any dcache_clean/dcache_invalidate-based implementation that
preserves correctness while allowing any arbitrary (non cache-aligned)
memory location as a transfer buffer is presumed to be impossible.
Instead, this patch causes all transfer data to be copied to/from a
cache-coherent bounce buffer. It will still transfer directly if the
supplied buffer is already cache-coherent, which can be used by callers
to optimize their transfers (and is true by default on x86).
Old-Change-Id: I112908410bdbc8ca028d44f2f5d388c529f8057f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169231
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 702dc50f1d56fe206442079fa443437f4336daed)
Squashed the initial commit and a follow up fix.
Change-Id: Idf7e5aa855b4f0221f82fa380a76049f273e4c88
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6633
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The readwrite_chunk was private to the usb mass storage driver, but wasn't
marked as static which was upsetting the compiler.
Change-Id: I0ef5c5f96a29f793dd43ff672a939902bad13c45
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/169816
Reviewed-by: Julius Werner <jwerner@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 8140e6145b3d072b7f12a924418570022207c065)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6648
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Currently, we wait for up to 30 seconds for a device to become ready to
respond to a TEST_UNIT_READY command. In practice, all media devices become
ready much sooner. But, certain devices do not function with libpayload's
USB driver, and always timeout. To provide a better user experience when
booting with such devices, reduce the timeout to 5 seconds.
Change-Id: Icceab99fa266cdf441847627087eaa5de9b88ecc
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169209
(cherry picked from commit 9e55204e92adca0476d273565683f211d6803e7a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6647
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When bringing up media, we claim to wait for up to 30 seconds for a
device to respond to our TEST_UNIT_READY command. Actually, we can wait
far longer because we do not take into account execution delay.
To improve timeout accuracy, make use of gettimeofday(), which calculates
time based upon a CPU counter. This improves the user experience
slightly when certain non-working USB devices are used.
Change-Id: Id9605ecfc0a522d7a0b039fd8eac541232605082
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169208
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 1d3d535db83ff478c512e37f37015b43927b3efc)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6646
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a new function to split transfer requests into chunks of
64KB in order to be as compatible as possible with devices that
choke when sent large transfer requests.
Change-Id: Id11990bd149af14af5535de4af47bda21d1ab51e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169170
Reviewed-by: Julius Werner <jwerner@chromium.org>
(cherry picked from commit 4c413b007aa23da830877127dd556c4c38b43042)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6636
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The current USB hub code always clears the port status change after
checking it, regardless of whether it was set in the first place. Since
this check runs on every poll, it might create a race condition where
the port status changes right between the GET_PORT_STATUS and the
CLEAR_FEATURE(C_PORT_CONNECT), thus clearing the statrus change flag
before it was ever read. Let's add one extra if() to avoid that possible
headache.
Change-Id: Idd46c2199dc6c240bd9ef068fbe70cccc88bac42
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/168098
(cherry picked from commit f7f6f008f701ab3e4a4f785032d8024d676e11cb)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6617
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The EHCI host controllers in Samsung Exynos SoC seem to be a little more
picky than Intel ones. When they reach the dummy_qh in the periodic
frame list, they try to access the next qTD pointer even though it's
NULL, and run into a HostSystemError. This patch explicitly sets the
Terminate bit on those pointers to mark them invalid.
Change-Id: I50fa79bbf1c5fab306d7885c01efd66b13e279b8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66884
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
(cherry picked from commit c575a5c958ce88732d28044352c89418bcd5ea86)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6608
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The USB bulk and control transfer functions in libpayload currently
always return 0 for success and 1 for all errors. This is sufficient for
current use cases (essentially just mass storage), but other classes
(like certain Ethernet adapters) need to be able to tell if a transfer
reached the intended amount of bytes, or if it fell short.
This patch slightly changes that USB API to return -1 on errors, and the
amount of transferred bytes on successes. All drivers in the current
libpayload mainline are modified to conform to the new error detection
model. Any third party users of this API will need to adapt their
if (...<controller>->bulk/control(...)) checks to
if (...<controller>->bulk/control(...) < 0) as well.
The host controller drivers for OHCI and EHCI correctly implement the
new behavior. UHCI and the XHCI stub just comply with the new API by
returning 0 or -1, but do not actually count the returned bytes.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48308
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Updated the patch to support XHCI as well.
Change-Id: Ic2ea2810c5edb992cbe185bc9711d2f8f557cae6
(cherry picked from commit e39e2d84762a3804653d950a228ed2269c651458)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6390
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The current XHCI code only sets IOC on the last TRB of a TD, and
doesn't set ISP anywhere. On my Synopsys DesignWare3 controller, this
won't generate an event at all when we have a short transfer that is not
on the last TRB of a TD, resulting in event ring desync and everyone
having a bad time. However, just setting ISP on other TRBs doesn't
really make for a nice solution: we then need to do ugly special casing
to fish out the spurious second transfer event you get for short
packets, and we still need a way to figure out how many bytes were
transferred. Since the Short Packet transfer event only reports
untransferred bytes for the current TRB, we would have to manually walk
the rest of the unprocessed TRB chain and add up the bytes. Check out
U-Boot and the Linux kernel to see how complicated this looks in
practice.
Now what if we had a way to just tell the HC "I want an event at exactly
*this* point in the TD, I want it to have the right completion code for
the whole TD, and to contain the exact number of bytes written"? Enter
the Event Data TRB: this little gizmo really does pretty much exactly
what any sane XHCI driver would want, and I have no idea why it isn't
used more often. It solves both the short packet event generation and
counting the transferred bytes without requiring any special magic in
software.
Change-Id: Idab412d61edf30655ec69c80066bfffd80290403
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170980
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit e512c8bcaa5b8e05cae3b9d04cd4947298de999d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6516
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When libpayload header files are included in the payload itself, it's possible
that the payloads config settings will conflict with the ones in libpayload.
It's also possible for the libpayload config settings to conflict with the
payloads. To avoid that, the libpayload config settings have _LP_ (for
libpayload) added to them. The symbols themselves as defined in the Config.in files
are still the same, but the prefix added to them is now CONFIG_LP_ instead of just
CONFIG_.
Change-Id: Ib8a46d202e7880afdeac7924d69a949bfbcc5f97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65303
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 23e866da20862cace0ed2a67d6fb74056bc9ea9a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6427
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This change makes it possible for vboot to avoid an
exploit that could cause involuntary switch to dev mode.
It gives depthcharge/vboot some information on the
type of input device that generated a key.
BUG=chrome-os-partner:21729
TEST=manually tested for panther
BRANCH=none
CQ-DEPEND=CL:182420,CL:182241,CL:182946
Change-Id: I87bdac34bfc50f3adb0b35a2c57a8f95f4fbc35b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://chromium-review.googlesource.com/182357
Reviewed-by: Luigi Semenzato <semenzato@chromium.org>
Tested-by: Luigi Semenzato <semenzato@chromium.org>
Commit-Queue: Luigi Semenzato <semenzato@chromium.org>
Reviewed-on: http://review.coreboot.org/6003
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Setting of `controller->reg_base` is of no use here, as it is never read
(in another function) later. Looks like this pattern originated from uhci.c
where it makes sense.
By removing the indirection through `reg_base` we also fix a possible
truncation to u32.
Change-Id: I5c99c5bf1f5b1d6c04bd84d87fd3e275fd7d0411
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6251
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Fix a possible null-pointer dereference (hopefully) before anyone runs
into this. Also don't switch ports to xHCI if initialization failed.
Change-Id: I5dbaeb435a98ead0b50d27fde13c9f1433ea3e81
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6245
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
As the controller structure is never fully cleared, this one wasn't
initialized for non-pci controllers (but checked for non-null later).
Change-Id: I852671c5f55650bdb6cd97f4ec74b1f95ee894c7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6246
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Using void* for physical addresses leads to much casting and confuses
developers when to convert from physical to virtual addresses or
the other way around. When using plain integers for physical addresses
and pointers for virtual addresses things become much cleaner and we
won't ever end up dereferencing a physical address.
Change-Id: I24cd53b81c7863b6d14f0cbb4ce8937728b37c1c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6244
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Remove a redundant phys_to_virt() that sneaked in the initialization of
PCI xHCI controllers. The use of casts from void* to u32 (and vice versa)
prompts for things going wrong here. That will be addressed in a later
commit.
Change-Id: Ibc71ed6ee7016529c0e3a51559aaec07aaaba315
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/6243
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
being a good citizen on the box, libpayload tries to return to EHCI
mode on shutdown, so a non-XHCI capable USB driver after it (eg. in
the OS) finds something to work with.
Change-Id: Id227d646e08a258b841c644263112f0815dd486c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/4547
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The EHCI driver defines a maximum transfer timeout of two seconds. The
comments state that during tests the maximum amount of required transfer
time was for the SCSI TEST_UNIT_READY command on certain devices. We
have now observed a USB device (Patriot Memory 13fe:3100) that can NAK
this command for slightly more than two seconds. It will also completely
fail if the timeout hits, since it gets confused by the subsequent CSW
retry/recovery mechanism and starts producing babble errors. This patch
increases the timeout to three seconds to circumvent this problem.
To test, boot a Falco from a red-black RageXT USB stick.
Change-Id: I3c4fef468fb16eacc5a487d76d025a78fb450e27
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63095
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/4379
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Mass storage devices such as card readers show up as
as USB devices. However the media not be inserted. In those
situations the previous code would just fake a disk and
call usbcreate_disk. This is inappropriate because it forms
a 1:1 mapping of USB device to disk leading to the inability
to remove the disk and/or handle "hot plug" card insertion
and removals.
To alleviate this issue introduce the notion of ready to the
usbmsc structure. It tracks detached, not ready, and ready
states. The polling routine is then used to track not ready
to ready transitions thereby creating and removing disks
appropriately. This handles the case of inserting and removing
a card that shows up as a new disk.
Booted recovery mode. Able to observe inerstion and removal
of sdcard. Also able to insert valid USB flash drive to boot
as well.
Change-Id: I3eefbe537ec1b9c975744b8984b06c17ae236f40
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57948
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4226
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is currently a hard-coded 30 sec delay in the mass storage
driver while waiting for each device to become ready. However, mass
storage card readers that are empty return an error code on the
TEST UNIT READY command. A REQUEST SENSE command then needs to be
issued and interrogate the data to determine if no media is present.
If no media determination is found to be true the USB device is no
longer considered a candidate to be a disk.
This code does lead to the fact that the media card reader needs to be
populated at enumeration time. I suspect this is not an issue as it
appears the storage stack in libpayload can't handle removable media
coming online later.
Booted recovery and dev modes. Noted that removable mass storage
devices with no media were ignored without any boot delay.
Change-Id: Ida7a45614d97c6e6fbfc9bb099765aad4df550fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57828
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4225
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Restructure USB stack to not depend on PCI, and
make PCI stub available on x86, but provide fixed
BARs for ARM (Exynos 5)
Change-Id: Iee7c8b134c22b661a9a515e24943470c9dbadd1f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49970
Reviewed-on: http://review.coreboot.org/4175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Two structures in the USB EHCI stack were pointing
to hardware but not marked attribute((packed)) hence
leaving it to GCC to correctly align the data structures.
Next, the number of reserved bytes in hc_op_t was wrong
(but implicitly aligned to the correct values on x86)
It seems this worked fine on x86, but on ARM it was doing
the wrong thing.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I94bed4850ded7d3f7bbc7ff3079c103c6054c22d
Reviewed-on: https://gerrit.chromium.org/gerrit/55555
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4174
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On Intel's Panther Point the xHCI ports are shared with an EHCI
controller. Our xHCI driver switches them to xHCI, naturally. But
we forgot to switch them back on shutdown, which left them
unusable by a non-xHCI aware operating system.
Change-Id: I70ef08655a603b42ee939935d50cf77ea97878a3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3791
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Well, it turned out to be more as some gaps ;)
but we finally have xHCI running. It's well tested against a QM77 Ivy
Bridge board.
We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not
advertised and USB 3 devices will just work at HighSpeed.
There are still some bit fields in xhci_private.h, so this might need
little more work to run on ARM.
Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3452
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is mostly a rewrite, don't even try to read a diff.
Tested with an internal rate matching hub on a QM77 board and three hubs
integrated into DELL monitors.
Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3451
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current drivers for external usb hubs and root hubs all follow
the same pattern. Before adding another one with 90% of the same code,
extract the common parts and rewrite them with a simple interface.
This also adds debouncing of new attachments. Current drivers just
waited 100ms before they reset the device. However, we should check
if the device becomes disconnected and reconnected during this period.
Porting of the current hub drivers will take place in separate
commits (when I have time to test the older HCIs).
Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3450
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
During device initialization, skip any non-endpoint descriptor before
reading the endpoint descriptors. By now, only HID descriptors were
skipped.
Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This change modifies the code in libpayload that scans the PCI hierarchy for
USB controllers. Previously, if a devices primary function (function 0) was a
bridge, then none of the other functions, if any, would be looked at. If one
of the other functions was a bridge, that wouldn't be handled either. The new
version looks at each function that's present no matter what, and if it
discovers that it's a bridge it scans the other side.
Change-Id: I37f269a4fe505fd32d9594e2daf17ddd78609c15
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2517
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The function dump_qh() was added a while back but never used.
Hide it behind USB_DEBUG so it doesn't cause warnings when not
debugging the USB stack.
Change-Id: Idb3c7bb214895ef82676d181836a578bf161e8e0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2909
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The controller's shutdown function free()s the controller structure so
we shouldn't access it any more after calling shutdown.
As all controllers detach themself, i.e. unchain themself from usb_hcs,
just keep iterating over usb_hcs until it's NULL.
Change-Id: Ie85caba0f685494c3fe04c550a5a14bc4158a94e
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
It shouldn't be used any more as we're about to free() the memory behind
the controller -- therefore detach it.
Change-Id: I875322a9940570c51d412a7f3bfb6af4ea3b3764
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: http://review.coreboot.org/2899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
And include the new, split out version in drivers/keyboard.c and
drivers/usb/usbhid.c. Those files were including curses.h just for those
definitions, but the include path was only fixed up to to point to the
libpayload versions of those files if one of the variants of curses was
compiled in. If neither was, gcc would fall back to the system version of that
header which is wrong.
Change-Id: I8c2ee0baf5f0702bd8c713c8dd4613a4bb269ce5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is static and not used in that file. To avoid the compiler
complaining about that fact, put the two functions and the call to dump_ed
(currently #if 0) behind #ifdef USB_DEBUG
Change-Id: Ic373313b5fff81f09800f286b32238350ab699c6
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It might be useful to provide a USB driver in the payload itself instead of in
libpayload. For example there are multiple payloads being built and linked
against the same libpayload, and they might not need or even want to have the
same set of drivers installed.
This change adds two new functions, usb_generic_create and usb_generic_remove,
which behave like the usbdisk_create and usbdisk_remove functions which are
defined for USB mass storage devices. If a USB device isn't recognized and
claimed by one of the built in USB class drivers (currently hub, hid, and msc)
and the create function is defined, then it will be called to give the payload
a chance to use the device. Once it's removed, if usb_generic_remove is
defined it will be called, effectively giving the payload notice.
Built and booted depthcharge on Link. Built depthcharge for Daisy. Built
a netbooting payload, called usb_poll() with those functions implemented, and
verified that they were called and that the devices they were told about were
reasonable and the same as what was reported by lsusb in the booted system.
Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2666
Tested-by: build bot (Jenkins)
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EHCI controllers see transfers as a queue of transfer descriptors
(qTDs), each of which can represent an aligned area of up to 20KB. Each
qTD is processed separately, which means that a single USB packet cannot
span multiple qTDs.
While this should not be a problem according to the specification, some
USB storage devices seem to get confused when a packet in the middle of
a transfer is smaller than the maximum packet size (512 bytes) due to
falling on a qTD boundary. This patch aligns the total transfer length
per qTD to 512 bytes to avoid that problem (any excess bytes will simply
roll over to the next qTD).
Change-Id: I0b5db07507699a3861b30c1a5ee774c45dda7fdd
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/2651
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Initialize the high part of the address
and use 64-bit compatible descriptors.
(waste a few bytes on 32-bit but should be harmless)
Read USB stick on a SandyBridge system which has 64-bit EHCI.
Change-Id: I59cc842459acecdde8f8bdd4795ebfeccb842c8f
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2650
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
That way when it's treated as a u32 when its value is extracted for numblocks
and blocksize below, it doesn't make the compiler unhappy, and it ensures that
the buffer will be properly aligned on architectures where that sort of thing
matters.
Built and saw warnings about type punning go away.
Change-Id: I254e0b5e70847112d660675b7df0ac9cb52e4051
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2653
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Shawn Nematbakhsh