This mainboard also has a SD slot.
Change-Id: Id56bc1be60ec8c2be0e5543d1d8851610b7248e0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard also has an external RTC chip, but not on this bus. The
topic is currently in clarification and will be published with a later
patch. In a first step we enable all I2C busses.
Change-Id: I9ec9631ed15ab30cc6a4594531521f4a1419ad00
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Enable all PCIe root ports for this mainboard.
Change-Id: I7f6feb2f0d4c45f32d9454838e67e1a244b2712b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is no device on I2C0 which requires a lower clock rate.
Change-Id: Ib7c4e3251545b2d32368dd56206e3b4844a24800
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
All PCIe root ports of this mainboard do not have an associated CLKREQ
signal. Therefore the ports are marked with "CLKREQ_DISABLED".
Change-Id: I834b3b0c77223d81c950e27ccfff8e9aeece2aa4
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there are legacy PCI device, which are connected to
different PCIe root ports via PCIe-2-PCI bridges. This patch disables
the unused PCI clock outputs on the XIO2001 PCI Express to PCI Bridges.
Change-Id: I2212c1080b72a656b5c8e68b040108a7adbec608
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard provides customer hardware reset button. A feature of
this button is that it holds the APL in reset state as long as the reset
button is pressed. After releasing the reset button the APL should
restart again without the need for a power cycle. When Bit 3 in Reset
Control Register (I/O port CF9h) is set to 1 and then the reset button
is pressed the PCH will drive SLP_S3 active (low).
Change-Id: Ib842f15b6ba14851d7f9b1b97c83389adc61f50b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is an on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I1ef4a7774d4ca75c230063debbc63d03486fed6f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
For this mainboard the correction of transmit voltage swing from SATA
interface is not necessary.
Change-Id: I900d0d44b88585c223182d85c78cf3ff1e3e9159
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason we have to adjust the PIR6
register (0x314c) which is responsible for PCIe device 13h and 14h. This
means that the interrupt routing will also be the same for both PCIe
devices. The bridge is connected to PCIe root port 2 and 3 over two
lanes (Device 13.0 and 13.1).
The following routing is required:
INTA#->PIRQD#, INTB#->PIRQA#, INTC#->PIRQB#, INTD#->PIRQC#
Change-Id: I5028c26769a2122b1c609ad7789c9949e3cb7a87
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29513
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change tcc offset from 0 to 10 for fleex.
Refer to b:117789732#1
BUG=b:117789732
TEST=Match the result from TAT UI
Change-Id: I481526ab10a16a33fe0cf9528b52b8524e012451
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
EC_SYNC_IRQ from EC to host is level-triggered in practice and
configuring it as edge-triggered on the host results in host missing
events if there are multiple events queued on the EC side. This is
because Linux kernel driver reads one event per irq and the EC does
not de-assert the interrupt line until all events are drained
out. This results in event queue being filled up completely on the EC
and the host failing to see any of those events.
This change configures EC_SYNC_IRQ as level triggered to allow the
host to read events from the the EC as long as the line is asserted.
BUG=b:118949877
Change-Id: Id3fcfa0445f83865d57975a7bbc179dca047ba4c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Link memory.c instead of including it.
Change-Id: I2bc461b13332ec5885c33c87828a5fd023f8e730
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
* Remove dead code
* Add support for types 2504 and 2505
* Print dock info at romstage entry
* Improve dock disconnect for type 2505
* Move defines into dock.h for future ACPI code
* Reduce timeouts according to spec to decrease boot time on error
* Fix no docking detection (reduces boot time by 1 second)
* Configure GPIO LDN before reading GPIOs
* Use Kconfig values instead of fixed defines
* Add documentation
Tested on Lenovo T500 with docking 2504 and 2505.
Change-Id: Ic4510ffadc67da95961cecd51a6d8ed856b3ac99
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This change disables HECI1 device at the end of boot sequence. It uses
the P2SB messaging to disable HECI1 device before hiding P2SB and
dropping privilege level.
BUG=b:119074978
BRANCH=None
TEST=Verified that HECI1 device is not visible in lspci on octopus.
Change-Id: Id6abfd0c71a466d0cf8f19ae9b91f1d3446e3d09
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change 76ab2b7 ("arch/x86: allow global .bss objects without
CAR_GLOBAL") allowed use of global .bss objects and hence moved around
the macros resulting in car_active returning 0 even for those boards
where CAR is actually active but do not require global migration. This
resulted in boards getting stuck when doing a reset in verstage because
the code flow incorrectly assumed that there was no CAR active and
hence triggered a cache invalidate.
This change fixes the above issue by returning 1 for car_active if
ENV_CACHE_AS_RAM is set even if global migration is not required.
BUG=b:109717603
TEST=Verified that board reset does not trigger cache invalidate in
verstage and does not result in board hang.
Change-Id: I182f3e4277c57d6c50f7fcac2be72514896b3c61
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peichao Li <peichao.wang@bitland.corp-partner.google.com>
Reviewed-by: Nick Chen <nickchen@ami.corp-partner.google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Now postcar is a standalone stage, add
it as target to all TPM bus drivers.
This is a required for a measured boot.
Change-Id: I758185daf3941a29883c2256b900360e112275e1
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/29546
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now postcar is a standalone stage give it a
proper type.
Change-Id: Ifa6af9cf20aad27ca87a86817e6ad0a0d1de17c8
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/29545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
It is able to do so if timestamps are initialized.
Change-Id: Ic95313a19646b66dc1633fb680e54bfc61ec90be
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/27330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
1. Add two parameters for panel initialization timing.
> lvds_poseq_varybl_to_blon
> lvds_poseq_blon_to_varybl
2. The BL_PWM is controlled by APU_EDP_BKLTEN_L/APU_DP_VARY_BL/
EDP_BKLTEN_L, so move APU_EDP_BKLTEN_L to early init stage,
and be enabled depends on SKU, thus we can control the delay
time by config APU_DP_VARY_BL.
BUG=b:118011567
TEST=emerge-grunt coreboot.
Change-Id: Ib20c48813b208d697b950b2f02a70a690e483fdb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ strom after S3 resume.
For sarien/arcada these are all runtime IRQs only, not wake capable.
Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select the option to disable eSPI when ACPI is enabled so the EC
is unable to assert an SMI when booted into the OS. There is a
kernel driver that implements the same mailbox interface so it
cannot also be used by the SMI handler.
Change-Id: I8bafc749f22aed5595e19e773762ee8b038950b9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add an option that will disable eSPI SMI when ACPI mode is enabled,
and re-enable eSPI SMI when ACPI mode is disabled. Additionally it
ensures eSPI SMI is disabled on the ACPI OS resume path.
This allows a mainboard to ensure that the Embedded Controller will
not be able to assert SMI at runtime when booted into an ACPI aware
operating system.
This was tested on a Sarien board with the Wilco EC to ensure that
the eSPI SMI enable bit is clear when booted into the OS, and remains
clear after resume.
Change-Id: Ic305c3498dfa4b8166cfdb070fc404dd4618ba3c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Change-Id: Ibde5f613c61c36f5c9b405326fd18a3fd16cca56
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/28840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Change-Id: Icb281f1b23c637971497eb28ed428235adf42f2d
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/28839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Change-Id: If462126df31468ef55ec52e2061b9f98d3015f61
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/28838
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the firmware slot configuration in VBOOT selectable. The following
three modes are available:
-RO only
-RO + RW_A
-RO + RW_A + RW_B
The mode "RO only" is the lowest mode with no safety during update.
You can select either RW_A or RW_AB via Kconfig which will add the
selected parttions to the final image.
Change-Id: I278fc060522b13048b00090b8e5261c14496f56e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/27714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
This patch also add new SKL PCH-H device id's in soc platform reporting and
common lpc driver.
BUG=None
TEST=Booted kabylake RVP11 with HM175 SKL PCH-H and verified the device id
in serial logs.
Change-Id: I8c04bf8d9c27caad800427a5c29da869da1d445d
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/29432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_D9 and GPP_D10 to use PLTRST.
BUG=b:119202293
TEST=none
Change-Id: I98d71100f28fb9bae05db3fb7d9afcb3f81beb43
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29538
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_C11 (FPMCU_INT_L) was set to DEEP, causing problems with S3.
Changed GPP_C11 configuration to use PLTRST instead.
BUG=b:114196791
TEST=Build, flash, boot nocturne, log in to kernel and execute
the following two commands and verify it passes :
echo 0 > /var/lib/power_manager/suspend_to_idle && restart powerd
sudo suspend_stress_test -c 2
Change-Id: I008532fce963c51a435378001440ac72b5ebfffc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
add the memory parts as ram id 10:
hynix_dimm_H5ANAG6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I137259b88f39779768a58959a2dcc565645eee6d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change allows to redirect coreboot console output to COM2 by
setting appropriate UART index in Console menu in Kconfig.
Change is helpful for users which would like to use COM1 port for
other purposes, because COM1 is the only port with hardware flow
control.
Change-Id: I39f88d7e7794f603775a985afe07fef349172e5f
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/29255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In case the function pointer isn't set return an error.
Change-Id: I9de300f651ac93889dafa7377c876bf5ae2c50cc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/29531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
VB2_LIB will be used across all stages to hash data. Add it to postcar
stage sources so that it is compiled if postcar exists. In this way the
new function tpm_measure_region() introduced in commit
61322d7 (security/tpm: Add function to measure a region device)
can be used in every stage.
Change-Id: I933d33b0188d1b123bb4735722b6086e7786624f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/29465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Fixes building vb2lib for postcar. Since postcar is an x86ism, add the
Kconfig options only for x86.
Change-Id: Ib92436bc7270c24689dcf01a47f0c6fe7661814b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29395
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The foreword mentioned that you need a gerrit account, but not how to
have git push with the right credentials.
To ease onboarding, point out where to get them.
Change-Id: I0b022bc064e3bc89568617c1a3a3e0e5236ba520
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This mainboard is based on mc_apl1. In a first step, it concerns a copy
of mc_apl1 directory with minimum changes. Special adaptations for
mc_apl4 mainboard will follow in separate commits.
Change-Id: I3dfdccc8198f3a23a45d319ede6080803a46f7f6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This mainboard variant requires GPIO adaptations to match the hardware.
Change-Id: I16387358d6c6fa15efd16f7ba7f6b89740477e9d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
* Move all implementations to into common folder.
* Add rtc.c for rtc based functions
Allows all Intel based platforms to use VBOOT_VBNV_CMOS.
Change-Id: Ia494e6d418af6f907c648376674776c54d95ba71
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
RCBA address numbers in comments looks wrong and confusing. Let's fix
them.
This is a cosmetic change since no actual data is added or removed.
Change-Id: I0e521acdac17959586bc0af7d8a2f7182f1e6721
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Elyes HAOUAS