Nothing can actually use this as the EC cannot speak
using baytrail's SERIRQ protocol. Also, the voltage
bridge is going away so nothing will be hooked up to it.
Therefore disable this it.
BUG=chrome-os-partner:24693
BRANCH=rambi
TEST=Built and booted.
Change-Id: I406bb9c227578ec0a75eaf67143b3b27cb7880ae
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182082
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/5042
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Set critical temperature thresdholds to 70C. This will cause DPTF
framework to shut down the system so it may need to be higher or
lower but will need some testing.
BUG=chrome-os-partner:17279
BRANCH=rambi
TEST=build and boot on rambi, start DPTF framework and observe it
using specified critical thresholds.
Change-Id: Ibbf6d814295eb5ff006cb879676b7613f5eb56a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/182025
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5038
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The SoC needs to provide a 32k clock signal SUSCLK for
some modems to work properly, so this enables the signal.
BUG=chrome-os-partner:24425
TEST=Manual, check SUSCLK pin with a scope.
Change-Id: Ibc0d5bb38a2c3e16f381dfc256097fdced67fd1c
Reviewed-on: https://chromium-review.googlesource.com/180101
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5722
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
Tested-by: build bot (Jenkins)
eMMC CLK was incorrectly configured as PULL_UP, but should have been
PULL_DOWN. 2K pulls somehow masked this problem.
BUG=chrome-os-partner:24353
TEST=Verify eMMC is bootable on Rambi on boards that previously failed
with an all-20K, all-PU eMMC pin configuration.
BRANCH=None
Change-Id: I0cbb6ebbb6818f83402b99330728266b09a0f5d6
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/181034
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5026
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Not used currently on rambi board. Disable in case it
saves power.
BUG=chrome-os-partner:23862
BRANCH=none
TEST=build and boot on rambi
Change-Id: Idb870c2cfa88cb6c3f1ada3caf0db566e33ec1eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/180084
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5020
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
With the ACPI GNVS exported and depthcharge changed to
initialize eMMC in ACPI mode we can now put the SCC
devices into ACPI mode.
BUG=chrome-os-partner:24380
BRANCH=none
TEST=build and boot on rambi, test eMMC and SD card
Change-Id: I39716198f8227c0c3293ac23eb09660792e2c51b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179901
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5018
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
This enables the DPTF framework, but it doesn't do much
without some sort of kernel+user components to drive it.
BUG=chrome-os-partner:17279
BRANCH=none
TEST=build and boot on rambi, dump DSDT and look over \_SB.DPTF
Change-Id: Icb632a6e70c3912bbdfa6ef3f5c87cd79d2b8a3a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179480
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5003
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
These are the values that are seen with VBIOS and
may need tweaked for derivative panels.
BUG=chrome-os-partner:24367
BRANCH=none
TEST=boot on rambi in normal mode and see the panel come up
Change-Id: Ie3120ab3c5298135626e8534d3954acd263dc74b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179365
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5001
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Now that the SD card controller is limited to the SD card
2.0 spec it's possible to use 20K pulls for the pads.
BUG=chrome-os-partner:24423
BUG=chrome-os-partner:24312
BRANCH=None
TEST=Built and booted. Able to dd to/from /dev/mmcblk1 without
any errors.
Change-Id: Id5396c55330a84bf7a09d227507d2bfcde66a1a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179423
Reviewed-on: http://review.coreboot.org/4999
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
The rambi board can only meet the SD card 2.0 specification.
Therefore, the controller capabilities need to be overridden
to match.
BUG=chrome-os-partner:24423
BRANCH=None
TEST=Built and booted. /sys/kernel/debug/mmc0/ios shows
high speed as maximum timing as well as 3.3V signal voltage.
Change-Id: Ib3824800852376e0f15a70584917d6692087ccfe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179415
Reviewed-on: http://review.coreboot.org/4998
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Bay Trail has 3 banks of gpios. Therefore, in order to
properly identify a gpio the specific bank number as well
as the GPIO within that bank is needed. The SPI
write-protect GPIO is GPIO 6 within the SUS bank (offset
0x2000).
BUG=chrome-os-partner:24324
BUG=chrome-os-partner:24408
BRANCH=None
TEST=Built and booted. Looked at GPIO sysfs in the
chromeos_acpi directory.
Change-Id: Ic51b5abe3bacf6cf9b6a90cf666f1a63b098a0e3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/179195
Reviewed-on: http://review.coreboot.org/4995
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Leave it under BOOTMODE_STRAPS to control whether these have
any functional meaning on the build.
Change-Id: Ieb59aa7ab4b1e8da6a1002e7a8e5462eb7988d35
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5643
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Strengthen PUs on all eMMC pins to fix problems with eMMC not coming up
on certain boards.
BUG=chrome-os-partner:24353
TEST=Manual. Burn FW on board that previously failed to boot eMMC,
verify chromeos can now install + boot from eMMC.
BRANCH=none
Change-Id: I7a9742968b8b8c2c42285ffc21de46aed9c87fb7
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178917
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4991
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Rambi 1.5 boards use the native SD card controller on baytrail.
Therefore, enable those signals. The CLK, D*, and CMD pins use
2K pulls as these were shown to not exhibit any errors when
doing reads or writes to a DDR50 sd card.
Note that if a servo is connected on needs to enable the
sd_vref_sel rail to pp1800 as this causes issues with card
detect if it is not set to pp1800.
BUG=chrome-os-partner:24312
BRANCH=None
TEST=Built and booted. Tested sd card read and write works in kernel.
Also noted that write protect detection works as well.
Change-Id: I520e2808acbd8494534fcb710411dbc0e12fc874
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178961
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4990
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Some 1.5 boards have a single channel ram configuration.
Accomodate such configs.
BUG=chrome-os-partner:22865
BRANCH=None
TEST=Built and booted ChromeOS.
Change-Id: I513327e47b9211d2dd1ea960d7da671a3773cb91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/178340
Reviewed-by: Nick Sanders <nsanders@chromium.org>
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Tested-by: Nick Sanders <nsanders@chromium.org>
Reviewed-on: http://review.coreboot.org/4983
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The level shifting between 3.3V and 1.8V for the SERIRQ
signal is not working. Instead use the SERIRQ pad as
a gpio which is used as a direct IRQ signal for the
keyboard interupt.
BUG=chrome-os-partner:23965
BRANCH=None
TEST=Built and booted rambi. Keyboard works with associated EC change.
CQ-DEPEND=CL:177189
Change-Id: Ifc270ca38207828a6d4711551d4bde9121559cca
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177223
Tested-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-on: http://review.coreboot.org/4979
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The romstage code for rambi uses the mmio way of reading
inputs. However, this is a problem is the GPIOs are set up
as legacy mode. Subsequent warm resets mean the ram_id is
read incorrectly. Ensure the ram_id is read consistently
by keeping the GPIOs for ram_id in mmio mode.
BUG=chrome-os-partner:24085
BRANCH=None
TEST=Built and booted. And rebooted. Now seeing consistent ram_id
values on warm resets.
Change-Id: Ieff98c000be80998854f325754f1e819975d2be5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/177230
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Some of the drivers in the kernel were not so happy about
having shared IRQs. Also, sharing IRQs means more code
needs to be run in interrupt context to determine if the IRQ
was meant for a particular device. Fix this.
No more 'mmc1: got irq while runtime suspended' messages.
BUG=chrome-os-partner:24056
BRANCH=None
TEST=Built and booted. Looked at /proc/interrupts and noted no
more sharing between pci devices.
Change-Id: Ie5da102204ffe3156dd55ab17af77df245a57c97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176792
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4973
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The kernel chromeos_laptop driver nomenclature expects the
board name to not be in all caps. Fix this as well as the i2c
address for the trackpad.
BUG=chrome-os-partner:24307
BRANCH=None
TEST=Built and booted. trackpad device is found. IRQs still not
working yet.
Change-Id: Id6be8ee4bce2835e303ea4fe63944be80d2d7ec2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176680
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4970
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Also add the relevant info about these pins to the ASL tables + add
SMBIOS type 41 data for these parts.
BUG=chrome-os-partner:22863
TEST=Manual on Rambi. Set some pins to GPIO_DIRQ, and then verify DIRQ
regwrites w/ GPIO_DEBUG look correct.
Change-Id: Id40655f9fb2ea7b10e1ff58d0b2a8b4cc6f05ff8
Reviewed-on: https://chromium-review.googlesource.com/176299
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Tested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4963
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
For some reason HDA can now be disabled. It's unclear what changes
in the baytrail code allowed this to happen, sadly.
BUG=chrome-os-partner:22871
BRANCH=None
TEST=Noted hda is not in lspci.
Change-Id: I64e2560533be6f701fa66cd53c906b62b09012ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176394
Reviewed-on: http://review.coreboot.org/4961
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Rambi has 3 pins that need to be configured for SCI and SMI:
1. GPIO_CORE[0] - runtime SCI pin
2. GPIO_SUS[7] - SMI for firmware lid events
3. GPIO_SUS[0] - wake pin for S3 wakes from EC.
Configure these pins now that the rest of the infrastructure
is in place. The one thing that is yet to work is runtime SCI
for lid events once booted.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=built and booted. lid close at rec screen works. And wake
from S3 with a keyboard press works.
Change-Id: I5f8e38ec5f4cf1a8ef7aa7fcee9abc344d9b184f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176393
Reviewed-on: http://review.coreboot.org/4960
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
As rambi is a baytrail board it doesn't have a dedicated wake pin.
Therefore, one needs to enable the proper GPIO to wake up the sytem
before going into S3.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Put system into S3. Keyboard press created wake event. Also, typed
'lidclose' on EC console while at recovery screen. Machine properly
shutdown.
Change-Id: Ic67b6bce93d57c620f498505d83197e4ae34a07d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176392
Reviewed-on: http://review.coreboot.org/4959
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The superio.asl file allows for the mainboard to hang
devices off of the LPC bus in ACPI. Include the keyboard
controller, EC memory map, and host interface's resources.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted. Noted resource reservations in dmesg.
Change-Id: Ida6481cd4c4725b5d3946bc64179ee99c93b0106
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176134
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4950
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Fix the SMI and SCI gpios for Rambi. Also, add in the
EC callbacks for the SMI handler. Note that the handler
for GPI SMIs has not been tested yet as baytrail chipset
code doesn't yet support setting up those configurations
yet.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Noted that SCI was enabled in /sys/firmware/acpi/interrupts
for the EC's SCI GPI. Also was able to see Chrome EC messages
with CONFIG_DEBUG_SMI and powering down at the dev screen.
Change-Id: I67b278fd38e1c09271d2c1e16e42f6e8c49e3a70
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176077
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4948
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Baytrail has a configurable SCI irq. Add support for
properly configuring SCI irq. Note that it is currently
fixed to IRQ9, but the code supports setting it to the
other supported values. The current mainboards using
baytrail defer the madt IRQ override information to the
chipset.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted. Noted 'SCI is IRQ9' message.
Change-Id: I7b307bd58f9de944f0cb4c116107a15345499f2e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176075
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4946
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
These changes to the eMMC pads allows the kernel to see the
eMMC device. One is able to install onto the eMMC device, and
the kernel is loaded and booted from eMMC device. Note, that
it may not fully boot because of other issues such as
not-completely working ACPI support.
BUG=chrome-os-partner:22580
BRANCH=None
TEST=booted off of usb drive. can see eMMC device.
Change-Id: I9c088398297a0b559383bdf4a389dd19a1110e0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/176073
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4945
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
For some mysterious reason GPIO_S0_NC22 is making the eDP panel
go entirely white when it is configured with internal pullup.
Since these (supposedly XDP related) pins are unknown functionality
lets set them to GPIO_DEFAULT instead of GPIO_NC.
Additionally the VBIOS is being changed to issue int15 callback
to determine the boot graphics device. If we list both LFP and EFP
then the dev/rec screens will show on the panel when HDMI is not
attached and otherwise will display on HDMI.
BUG=chrome-os-partner:23507
BRANCH=rambi
TEST=build and boot on rambi, see firmware/kernel screens on the panel
when HDMI is not attached, and firmware screens on the panel and
kernel screens on both when HDMI is attached.
Change-Id: Ieb05a591d63c4f8e09fa154eeb76004d32579508
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175952
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4944
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The FADT for baytrail had incorrect offsets leading to
the kernel spewing a huge mess of ACPI errors. Fix these offsets
to be initialized in the chipset code.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted into kernel on rambi. Login screen comes up.
Change-Id: I89fc2a4fd800ff01cedf89b51cfb1369aceb9f03
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175663
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4941
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This provides the initial support for interrupt routing
in bay trail. It includes both acpi changes and board changes
to ensure the interdependencies are met with the current ASL
code. The PIRQ routing is handled by the mainboard exporting
an irqroute.h header that describes the per device and PIRQ
PCI settings.
There are still a lot of ACPI errors in the kernel with this
change, though.
BUG=chrome-os-partner:23505
BRANCH=None
TEST=Built and booted rambi into kernel.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Id8a865a24fc8d49743c0b54efdb64aaef52fcd8e
Reviewed-on: https://chromium-review.googlesource.com/175700
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4940
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
CONFIG_ARCH is a property of the cpu or soc rather than a property of the
board. Hence, move ARCH_* from every single board to respective cpu or soc
Kconfigs. Also update abuild to ignore ARCH_ from mainboards.
Change-Id: I6ec1206de5a20601c32d001a384a47f46e6ce479
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5570
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
A global flag oprom_is_loaded was used to indicate to
U-boot that VGA option ROM was loaded and run, or that
native VGA init was completed on GMA device.
Implement this feature without dependency to CHROMEOS option
and replace use of global variable oprom_is_loaded with call
to gfx_get_init_done().
Change-Id: I7e1afd752f18e5346dabdee62e4f7ea08ada5faf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4309
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently we have no developer or recovery mode switches when
building without ChromeOS.
Change-Id: I49adfcd8408838cf581430970be5efcef11ba06b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5596
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
There is a lot of NVS allocated to things that are not really
used. Most of these are removed and some are moved around.
Thermals are expected to be handled with DPTF so I've removed
that bit of code but have not yet cleaned up the thermal zone.
I left in the SIO BARs since I think we will need those still
even though they may need work still.
BUG=chrome-os-partner:23505
BRANCH=rambi
TEST=build and boot on rambi
Change-Id: Id16ee67e6b3709a303c001afd72947147f938127
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175626
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4936
Tested-by: build bot (Jenkins)
Add a length define for all the reserved MMIO regions and
use them in the ACPI code to reserve the regions there.
Add a region for the "abort page" documented in the EDS.
BUG=chrome-os-partner:23505
BRANCH=rambi
TEST=build and boot on rambi
Change-Id: I2060dca0636a2fdc0533ddd0826f94add2c272c3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175624
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4934
Tested-by: build bot (Jenkins)
- a few clock gating bits were set improperly and were preventing
the system from transitioning out of S0 state.
- the XHCC registers were not getting the top byte set properly
which includes things like DMA write request size and request
boundary crossing control. This was causing memory corruption.
BUG=chrome-os-partner:23635
BRANCH=rambi
TEST=build and boot kernel from USB on rambi with XHCI driver
Change-Id: I8e8135a793dfbaa1f163766702e3a8f19bba9703
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/175558
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4933
Tested-by: build bot (Jenkins)
Correct selection of UART depends of board layout, not the CPU
internals, so default setting should originate from mainboard.
Change-Id: Ibf0ab0847ccce73c22704e86983dbe3d24ebc8a0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5618
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Rename coreboot_ram stage to ramstage. This is done in order to provide
consistency with other stage names (bootblock, romstage) and to allow any
Makefile rule generalization, required for patches to be submitted later.
Change-Id: Ib66e43b7e17b9c48b2d099670ba7e7d857673386
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5567
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
There is redundancy in terms of use of init_timer. We have a Kconfig option to
decide whether a board has init_timer as well as we use a stub for init_timer in
places where we do not have any init_timer defined. Thus, remove the Kconfig
option. Henceforth, all boards that do not have init_timer functionality can
include a stub_timer if required.
Change-Id: I35d38ec686f4dc92861cf9248f9b540323cd98ae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5569
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch implements a simple interface between the EC and mainboard
ASL code. This interface does not rely on the preprocessor, and
prevents name conflicts by scoping the interface methods. As this
interface is documented on the coreboot wiki, an in-tree documentation
is not provided.
Change-Id: If0b09be4f5e17cc444539a30f0186590fa0b72b5
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5515
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
The GP15 ACPI object was used to get the state of the lid. However
GP15 is specific to certain Intel chipsets, and will not always be in
the ACPI namespace. Instead of hardcoding this object, let the
mainboard define it.
Also, document the ACPI interface for the EC.
Change-Id: I02a2eb3116af61ea5701f84507327aa40218597a
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5444
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
