One could not pass a device of type APIC to PCI resource functions.
The correct CPU model specific cpu->ops is set at later time in
cpu_initialize().
Change-Id: Ifa274185e4db3080433c1f07e3a48f2b55c0514f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1180
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Northbridge code incorrectly adjusted the last cacheable memory
resource to accomodate room for UMA framebuffer. If system had
4GB or more memory that last resource is not below 4GB and not
the one where UMA is located.
There are three consequences:
The last entry in coreboot memory table is reduced by uma_memory_size.
Due the incorrect code in northbridge code state.tomk,
end of last resource below 4GB, had not been adjusted.
Incrementing that by uma_memory_size diverts a region
possibly claimed for MMIO to RAM, as TOP_MEM is written.
Since the UMA framebuffer did not have IORESOURCE_CACHEABLE,
it was ignored from the MTRR setup and not set uncacheable.
The setting of TOP_MEM and TOP_MEM2, as well as all the MTRRs,
should be copied from BSP to all APs instead of deriving the data
separately for each Logical CPU.
Change-Id: I8e69fc8854b776fe9e4fe6ddfb101eba14888939
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1217
Tested-by: build bot (Jenkins)
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use state.tomk to refer TOP_MEM, largest RAM address below 4GB.
Use state.tom2k to refer TOP_MEM2, largest RAM address above 4GB.
When setting either TOP_MEM or TOP_MEM2, any RAM resource found
must fit below the set value. Thus, round register value upwards,
not downwards.
Change-Id: I436c1b3234c911680ce8b095052f8d71f40113e2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1216
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
If northbridge called uma_resource() a resource of this type
should be found when walking the resources list.
For now, be rude and don't even try to combine it with
neighboring regions. As the type is un-cacheable it is
dominant over other MTRR setups claiming the same region.
Change-Id: I57805e7e7da0709f8ed78d8df62c2abf22172a06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1215
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
MTRR setup code can detect this and mark it as UC/WT/WC as suitable
for the specific hardware.
Change-Id: Ib7a3d450fc7c19e3ca72767dfb350412dd35c971
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1214
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These boards had identical UMA code:
amd/dbm690t
amd/pistachio
technexion/tim5690
technexion/tim8690
The ones below had whitespace or debug level change
compared to the one above:
kontron/kt690
siemens/sitemp_g1p1
These boards use AMDFAM10 guidelines in code:
asrock/939a785gmh
amd/mahogany
Change-Id: Id7c3f48035727f5847f2d7c3a6e87a3d15582003
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1210
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following boards had identical code:
advansus/a785e-i
amd/bimini_fam10
amd/mahogany_fam10
asus/m5a88-v
avalue/eax-785e
gigabyte/ma78gm
iei/kino-780am2-fam10
jetway/pa78vm5
Following boards had identical code:
amd/tilapia_fam10
asus/m4a78-em
asus/m4a785-m
gigabyte/ma785gm
gigabyte/ma785gmt
In between the two, only whitespace difference.
Change-Id: Iaa48cc7b0038ebcc81be49219b4fc87670aa9941
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1209
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following boards had identical code:
amd/inagua
amd/persimmon
The following had only whitespace or debug level changes
compared to ones above.
amd/union_station
amd/south_station
asrock/e350m1
Change-Id: I11ee46e06e1dd510cba551166189ebcaa144464b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1208
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Like ram_resource(), but reserved and not cacheable.
Switch all AMD northbridges to use this one.
Change-Id: I88515c6a0f59f80fd8607c390d0d4a2a35d805f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1203
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The current code didn't reserve static resource the right way.
Also reduce TOLM to 0xd0000000, because those boards have so many PCI
devices that 0xe0000000 isn't sufficient.
Change-Id: Ia75a81905eea1a096aed464b63ac154e044bc99c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1220
Tested-by: build bot (Jenkins)
Code can easily make the mistake of using uninitialized
values or, in assembly, mistakenly dereferencing stack pointers
when an address is desired.
Set the stack to a non-zero value which is also (by testing)
a pointer which will crash coreboot if used. This poisoning
has uncovered at least one bug.
Change-Id: I4affb9a14b96611e8bf83cb82636e47913025a5d
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1221
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
And fix the wrong indenting of devicetree.cb while at it.
Change-Id: Idbb19fb5d7155f44675098e79920caf65191c239
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1222
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Hudson code has been integrated from CIMx to AGESA. This patch is about the wrapper.
Change-Id: I63d951982140b82a3a77a97eb3d55fc75fc0caa3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1157
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The lex compile wasn't current (or something) and so INTA wasn't lexed
properly.
Change-Id: I5a760430788792f54c4e1e0d419b8dd525079d15
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1226
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Linux boots fine :)
Change-Id: Ifda06e5220666534b87f528deae16d8b956c32b3
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1225
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This register is helpful for porting new mainboards based on
cs5536 southbridge.
Change-Id: Iff3adc2c2fbc672c8541096756f95b3322f6ab19
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1211
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch adds support for autogenerating the MPTABLE from
devicetree.cb. This is done by a write_smp_table() declared
weak in mpspec.c. If the mainboard doesn't provide it's own
function, this generic implementation is called.
Syntax in devicetree.cb:
ioapic_irq <APICID> <INTA|INTB|INTC|INTD> <INTPIN>
The ioapic_irq directive can be used in pci and pci_domain
devices. If there's no directive, the autogen code traverses
the tree back to the pci_domain and stops at the first device
which such a directive, and use that information to generate the
entry according to PCI IRQ routing rules.
Change-Id: I4df5b198e8430f939d477c14c798414e398a2027
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1138
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Missed to add the driver to Kconfig and Makefile.inc.
Change-Id: I64b02abc5de2f6483f610436ebb38a7ca433f9b6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1219
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
All but one board use the default value of enabled. Disabling
this can only increase the number of MTRR registers used.
Change-Id: I7d28adc31b9fae2301e4ff78fcb96486f81d5ec2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1213
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Implemented OHCI reset function ohci_reset() in ohci.c
for libpayload's USB driver.
Change-Id: Id6518cbe00a21202757b34926bad171909740e97
Signed-off-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-on: http://review.coreboot.org/1177
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support to dump all data registers for Nuvoton chips (NCT6775F, NCT6776F,
and NCT6779D). Register contents will be dumped if the -e option is provided on
the command line.
Change-Id: I2b425b48c1f28a10ff3c1ca1d7f21c501eff74ad
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-on: http://review.coreboot.org/1150
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add new function dump_data() to dump a bank of superio data registers.
Change-Id: I13a58d87c14d319cfcdea1ec1d54c2b110d90f9f
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-on: http://review.coreboot.org/1149
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
There are two errors in the code. The first one is a missing
$ sign in mov _stack, %esp. Thanks to Ronald G Minnich for
catching that bug.
The second bug is the 'incl %eax', which shouldn't be there, as
there's no secondary CPU with index 0. CPU0 uses always the stack
below _estack.
Change-Id: Id267a654ba95b0e898eeaaafb2403b438250a563
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1212
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
If a CPU was pre-allocated, cpu_path is not copied and thus
index would not be updated. This breaks cpu_index() and AMD
model_fxx is possibly broken without this patch.
Change-Id: I77483181cf0bca31423c655942c022bffab3c7ea
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1199
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
If threads called alloc_find_dev() with same device_path
simultaneously, two device nodes could be allocated.
This bug is not triggered by current code.
Change-Id: Ifc87021c8d6f422901c5de5dd17392e3e2309afa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1188
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Remove superfluous pkg* definitions and installation of a target
directory directory that is never used.
Change-Id: I2addf3f316230cdd428def5889fd3beb7c40f422
Signed-off-by: Raymond Danks <ray.danks@se-eng.com>
Reviewed-on: http://review.coreboot.org/1195
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Not all users use both functions, so add __attribute__((unused))
to prevent compiler errors.
Change-Id: I8485bb9150b04d1f9fdc231152a43bcd6fc713a7
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1193
Tested-by: build bot (Jenkins)
Don't stop if RAM init fails at first try. It's better to restart
and try again instead of failing on the first try if the second
try would have worked.
Change-Id: Ib5660265d5b10a01588f2e4022dac2ee34f2c6d0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1191
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Implements support code for talking to IPMI hardware that uses
a KCS style interface.
Change-Id: I9895cc1bf29676115b167081b63b8a430e23eee5
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1190
Tested-by: build bot (Jenkins)
The Kconfig file for this board contains a bogus option called
CORE_GLIU, this change removes it.
Change-Id: I4ea069bdd76be53085ebc9c0fb3dd71ffb2a12e1
Signed-off-by: Ricardo Martins <rasmartins@gmail.com>
Reviewed-on: http://review.coreboot.org/1179
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This is mostly necessary for reboot, but it doesn't hurt the boot process.
On reboot explicitely reset the integrated graphics, otherwise the VGABIOS
might not be able to reinitialize it properly, and you either have a still
of the last pre-reboot image, garbage or an empty screen, but no text-mode.
Change-Id: Ic3d6932fbaf720d88daaac7e4b09c3c0b9f0b0e2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1178
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The superiotool Makefile extracts a version string from SVN. This does not work
with a git repository, and results in an empty version string. Use the output of
'git describe' as version string instead.
Change-Id: Idf92c02753b28ef5bcdd3b6df4a08d79ae974434
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-on: http://review.coreboot.org/1151
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
PCI Type 2 config was a strange and never-used config mechanism.
It is unlikely that in the 13 years of coreboot's existence that
type 2 was ever used; it just made life complicated for everyone.
It lived long enough in coreboot to be replaced by mmioconf.
Prior to making the device tree visible in romstage we want to
get rid of type2.
Delete two files we don't need any more (yay!).
Replace two functions with one: pci_config_default, which returns
a pointer to the default config method. At some future time this
may change to mmio but for now it is old type1 style.
Change-Id: Icc4ccf379a89bfca8be43f305b68ab45d88bf0ab
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1159
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
The SIPI vector copy can use a static location below 1MB, aligned
to 4kB. Jump out of the copy once in protected mode.
Change-Id: I6299aa3448270663941cf2c4113efee74bcc7993
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1165
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
CACHE_ROM_SIZE default is ROM_SIZE, the Flash device size set
in menuconfig. This fixes a case where 8 MB SPI flash MTRR setup
would not cover the bottom 4 MB when ramstage is decompressed.
Verify CACHE_ROM_SIZE is power of two.
One may set CACHE_ROM_SIZE==0 to disable this cache.
Change-Id: Ib2b4ea528a092b96ff954894e60406d64f250783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1146
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Kyösti Mälkki