Since a long time GRUB 2 is a viable payload alternative to SeaBIOS and
FILO. So make it easy for coreboot users to use GRUB 2 as a payload by
integrating it into coreboot’s build system, so it can be selected in
Kconfig.
As the last GRUB 2 release 2.00 is too old and has several bugs when
used as a coreboot payload only allow to build GRUB 2 master until a new
GRUB release is done. The downside is, that accidental breakage in
GRUB’s upstream does not affect coreboot users.
Currently the GRUB 2 payload is built with the default modules which
results in an uncompressed size of around 730 kB. Compressed it has a
size of 340 kB, so it should be useable with 512 kB flash ROMs.
Tested with QEMU.
Change-Id: Ie75d5a2cb230390cd5a063d5f6a5d5e3fab6b354
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4058
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It is for crossgcc.
Change-Id: Ia1d676adfea340b6b80858215459491c9338d614
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3955
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
On Intel's Panther Point the xHCI ports are shared with an EHCI
controller. Our xHCI driver switches them to xHCI, naturally. But
we forgot to switch them back on shutdown, which left them
unusable by a non-xHCI aware operating system.
Change-Id: I70ef08655a603b42ee939935d50cf77ea97878a3
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3791
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
keyboard_init attempts to read the existing mode register, set the
'XLATE' bit, and write it back. The implementation is buggy because the
keyboard may be active at the time we read the mode, and we can
misinterpret scancode data as the reply to our command. It leads to
problems where the KB gets disabled in firmware.
In fact, setting the 'XLATE' bit is completely unnecessary, even if we
desire QEMU keyboard support. We already set this bit when we initialize
the keyboard in pc_keyboard_init. Basically, this code does nothing
(or worse), so just remove it.
Change-Id: Iab23f03fa8bced74842c33a7d263de5f449bb983
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/3883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For libpayload clients with larger memory needs (eg. FILO with integrated
flashrom) the current configuration isn't enough.
Change-Id: Ic82d6477c53da62a1325400f2e596d7d557d5d1e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3889
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Change-Id: Ie69ceb343494b7dd309847b7d606cb47925f68b6
Reviewed-on: http://review.coreboot.org/3888
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Prettier in real-world payloads (ie. FILO)
Change-Id: I9ed968fe527c5d46090e707e2d89b7406a43662e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3887
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
flashrom has started to use revision IDs to distinguish AMD chipsets
and fails (even more) to build with libpayload since then because
PCI_REVISION_ID is undefined in libpayload's pci header.
Change-Id: If7440a48c1005a4ba4fc09303f47cdfa9f408ad1
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/3884
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
For reasons explained in a previous CL, it might be necessary to "load" a file
from CBFS in place. The loading code in CBFS was, however, zeroing the area of
memory the stage was about to be loaded into. When the CBFS data is located
elsewhere this works fine, but when it isn't you end up clobbering the data
you're trying to load. Also, there's no reason to zero memory we're about to
load something into or have just loaded something into. This change makes it
so that we only zero out the portion of the memory between what was
loaded/decompressed and the final size of the stage in memory.
Change-Id: If34df16bd74b2969583e11ef6a26eb4065842f57
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3579
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Instead of returning 0 on success and -1 on error, return the decompressed
size of the data on success and 0 on error. The decompressed size is useful
information to have that was being thrown away in that function.
Change-Id: If787201aa61456b1e47feaf3a0071c753fa299a3
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The memset and memcpy functions are assembled as ARM code, likely because
that's the default of the assembler. Without special annotation, the assembler
and linker don't know that those symbols are functions which need special
handling so that ARM/thumb issues are handled properly. This change adds that
annotation which gets those functions working in Coreboot which is compiled as
thumb. Libpayload and depthcharge are compiled as ARM so they don't *need* the
annotation since it just works out in ARM mode, but it's the safe thing to do
in case we change that in the future.
We should explicitly select ARM vs. thumb when assembling assembly files to be
consistent across builds and toolchains.
Change-Id: I814b137064cf46ae9e2744ff6c223b695dc1ef01
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3672
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The counted delay of 1ms was shorter than the time usb_poll() took
(~30ms observed). So with a given timeout of 100ms it actually took 3s.
We can lower the problem if we delay 10ms per loop iteration.
Change-Id: I6e084bdd05332111cc8adcd13493a5dfb4bc8b28
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3533
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Teach lpgcc to look in the in-coreboot tree directory structure, too.
Change-Id: I3809456d072ce2f91542b0edb3fd39f536298cc2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3530
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We can't read the drives signature before it's ready, i.e. spun up.
So set the timeout to the standard 30s. Also put a notice on the
console, so the user knows why the signature reading failed.
Change-Id: I2148258f9b0eb950b71544dafd95776ae70afac8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A timeout while waiting for a device' signature has shown that our
error path wasn't correct. The shutdown of the ports command engine
always timed out. Fix that by waiting for FR (FIS Receive Running)
to be cleared independently from CR (Command List Running) and after
clearing FRE (FIS Receive Enable).
Change-Id: I50edf426ef0241424456f1489a7fc86a2cfc5753
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3494
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Well, it turned out to be more as some gaps ;)
but we finally have xHCI running. It's well tested against a QM77 Ivy
Bridge board.
We have no SuperSpeed support (yet). On Ivy Bridge, SuperSpeed is not
advertised and USB 3 devices will just work at HighSpeed.
There are still some bit fields in xhci_private.h, so this might need
little more work to run on ARM.
Change-Id: I7a2cb3f226d24573659142565db38b13acdc218c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3452
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is mostly a rewrite, don't even try to read a diff.
Tested with an internal rate matching hub on a QM77 board and three hubs
integrated into DELL monitors.
Change-Id: Ib12fa2aa90af4e0f37143d2ed92c4a1705b6d774
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3451
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current drivers for external usb hubs and root hubs all follow
the same pattern. Before adding another one with 90% of the same code,
extract the common parts and rewrite them with a simple interface.
This also adds debouncing of new attachments. Current drivers just
waited 100ms before they reset the device. However, we should check
if the device becomes disconnected and reconnected during this period.
Porting of the current hub drivers will take place in separate
commits (when I have time to test the older HCIs).
Change-Id: I0c0ce0ac1b1cc51fb4cd009b3f9fcd1b9d2ba8fe
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3450
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Read bInterval from endpoint descriptors and store it in our endpoint_t
struct. The interval is encoded dependently on the device' speed and the
endpoint's type. Therefore, it will be normalized to the binary logarithm
of the number of microframes, i.e.
t = 125us * 2^interval
The interval attribute will be used in the xHCI driver.
Change-Id: I65a8eda6145faf34666800789f0292e640a8141b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3449
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
xHCI requires special treatment of set_address since it determines
the device number itself (instead of the driver, as with the other
controllers). The controller also wants to validate a chosen device
configuration and we need to setup additional structures for the
device and the endpoints.
Therefore, we add three functions to the hci_t structure, namely:
set_address()
finish_device_config()
destroy_device()
Current implementation for the Set Address request moved into
generic_set_address() which is set_address() for the UHCI, OCHI and
EHCI drivers. The latter two are only provided as hooks for the xHCI
driver.
The Set Configuration request is moved after endpoint enumeration.
For all other controller drivers nothing changes, as there is no other
device communication between the lines where the set_configuration()
call moved.
Change-Id: I6127627b9367ef573aa1a1525782bc1304ea350d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3447
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These values are already used in this usb stack.
Change-Id: If96f1dc2b67fbc13dfc4ae2d84e8f9945aa03163
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3448
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
During device initialization, skip any non-endpoint descriptor before
reading the endpoint descriptors. By now, only HID descriptors were
skipped.
Change-Id: I190f3ae44b864aa71d5f32c3738097cf8f33a61b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Add the Mobile Panther Point (PPT) AHCI controller (DEVID 0x1e03) to
the list of tested controllers. Also comment the only other listed
controller (Mobile ICH9).
The PPT AHCI controller was tested with a QM77 chipset on a Kontron
KTQM77 board.
Change-Id: Ia396761411f4f9289af11ec8e1b144512b2fc126
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes the configuration where serial console output is
being sent to non-existant hardware to be captured with I/O
trapping. In this configuration where there isn't serial
hardware present we still want to init the consoles. We just
never want to read non-existant hardware.
Change-Id: Ic51dc574b9c0df3f6ed071086b0fb2119afedc44
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3249
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The cbfs core code would print out the name of the file it is
searching for and when it is found would print out the name
again. This contributes to a lot of unnecessary messages in a
functioning payload’s output. Change this message to a DEBUG one
so that it will only be printed when CONFIG_DEBUG_CBFS is enabled.
Change-Id: Ib238ff174bedba8eaaad8d1d452721fcac339b1a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3208
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The cbfs core code would print out all unmatched file
names when searching for a file. This contributes to a lot
of unnecessary messages in the boot log. Change this
message to a DEBUG one so that it will only be printed when
CONFIG_DEBUG_CBFS is enabled.
Change-Id: I34c747e0d3406351318abf70994dbc0bb3fa6c01
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3164
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Because pointers can be 32bit or 64bit big,
using them in the coreboot table requires the
OS and the firmware to operate in the same mode
which is not always the case. Hence, use 64bit
for all pointers stored in the coreboot table.
Guess we'll have to fix this up once we port to
the first 128bit machines.
Change-Id: I46fc1dad530e5230986f7aa5740595428ede4f93
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3115
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
The way we got to include the compiler includes was kind of whacky.
Instead of mixing in potentially problematic headers, make libpayload
self-contained by adding some missing header files. Also clean up
conflicting definitions of size_t throughout the tree.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I0ad1194de1a00b7133c5477c00eb167d63a2ee85
Reviewed-on: https://gerrit.chromium.org/gerrit/47608
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3058
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reading commit »libpayload: New AHCI, ATA and ATAPI drivers«
(1f6bd94f) [1], the spelling error was found and is now fixed.
[1] http://review.coreboot.org/1622
Change-Id: Id418bcb99c1a9a400a49fc04078e465bd0908074
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3071
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change modifies the code in libpayload that scans the PCI hierarchy for
USB controllers. Previously, if a devices primary function (function 0) was a
bridge, then none of the other functions, if any, would be looked at. If one
of the other functions was a bridge, that wouldn't be handled either. The new
version looks at each function that's present no matter what, and if it
discovers that it's a bridge it scans the other side.
Change-Id: I37f269a4fe505fd32d9594e2daf17ddd78609c15
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2517
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Nico Huber spotted [1], that commit (4d6ab4e2) [1] updating
superiotools’s `README` with the Git command line
superiotool: Update README with Git repository URL and directory location
missed, that after `git clone` one sitll has to change into
the cloned directory.
So prepend the path with `coreboot/` to fix that. The same error
happened in the commit (e1ea5151) for libpayload [2]
libpayload: Update README with Git repository URL and directory location
and is fixed in this patch too.
[1] http://review.coreboot.org/#/c/3019/
[2] http://review.coreboot.org/2228
Change-Id: Ib6e8b678af6276556a40ccfd52ae35ca7e674455
Reported-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3021
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Building libpayload with the PDCurses backend the following warning
is shown.
/src/coreboot/payloads/libpayload(master) $ make clean
/src/coreboot/payloads/libpayload(master) $ make
[…]
CC curses/pdcurses-backend/pdcscrn.libcurses.o
curses/pdcurses-backend/pdcscrn.c: In function 'PDC_scr_open':
curses/pdcurses-backend/pdcscrn.c:75:5: warning: "CONFIG_SPEAKER" is not defined [-Wundef]
[…]
The GCC documentation states [1]
In some contexts this shortcut is undesirable. The -Wundef option
causes GCC to warn whenever it encounters an identifier which is
not a macro in an ‘#if’.
and therefore use `#ifdef` [2] to silence this warning. No functional
change is done, as `CONFIG_SPEAKER` is assigned the value `Y` when
defined.
There was some discussion going on the list [3], but my points in there
turned out to be incorrect.
[1] http://gcc.gnu.org/onlinedocs/cpp/If.html
[2] http://gcc.gnu.org/onlinedocs/cpp/Ifdef.html
[3] http://www.coreboot.org/pipermail/coreboot/2013-March/075561.html
Change-Id: I8e9c9b5d01985b21ad05018986d614cf9bf2b439
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2934
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Tested-by: build bot (Jenkins)
This imports the newest cache and MMU code from coreboot. This
time it's so new that it hasn't even been checked in to coreboot.
However, this version at least allows DMA to work properly for the
MSHC driver. So even if we rebase a few more times, this version is
at least a step in the right direction.
Note: This omits the stuff that sets up dcache policy since
libpayload should not need to worry about that and it depends
on cbmem stuff.
Change-Id: Idd42b083e8019634aaaa44d5bf5b51db6c3912f5
Signed-off-by: David Hendricks <dhendrix@google.com>
Reviewed-on: http://review.coreboot.org/2975
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
This imports the new cache maintenance API from coreboot at
commit bba8090. This is a BSD-licensed implementation which
exposes cache maintenance opertaions necessary for payloads
for things such as DMA transfers.
Change-Id: I554676db89517bebc6edae4f7ab7e5882e6f986d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2974
Tested-by: build bot (Jenkins)
On x86, coreboot may allocate a variable range MTRR for enabling caching
of the system ROM. Add the ability to parse this structure and add the
result to the sysinfo structure.
An example usage implementation would be to obtain the variable MTRR
index that covers the ROM from the sysinfo structure. Then one would
disable caching and change the MTRR type from uncacheable to
write-protect and enable caching. The opposite sequence is required
to tearn down the caching.
Change-Id: I3bfe2028d8574d3adb1d85292abf8f1372cf97fa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2920
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes the following PDCurses warnings:
CC curses/pdcurses-backend/pdcsetsc.libcurses.o
curses/pdcurses-backend/pdcsetsc.c: In function 'PDC_curs_set':
curses/pdcurses-backend/pdcsetsc.c:17:9: warning: implicit declaration of function 'serial_cursor_enable' [-Wimplicit-function-declaration]
curses/pdcurses-backend/pdcsetsc.c:22:9: warning: implicit declaration of function 'video_console_cursor_enable' [-Wimplicit-function-declaration]
CC curses/pdcurses-backend/pdcutil.libcurses.o
curses/pdcurses-backend/pdcutil.c:30:6: warning: no previous prototype for 'curses_enable_serial' [-Wmissing-prototypes]
curses/pdcurses-backend/pdcutil.c:35:6: warning: no previous prototype for 'curses_enable_vga' [-Wmissing-prototypes]
curses/pdcurses-backend/pdcutil.c:40:5: warning: function declaration isn't a prototype [-Wstrict-prototypes]
curses/pdcurses-backend/pdcutil.c:45:5: warning: function declaration isn't a prototype [-Wstrict-prototypes]
Change-Id: If0d4d475d3006f1a77f67ec46c6bdf4ee2906981
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2908
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There were a number of type issues in libpayload that sneaked in
with 903f8e0.
- size_t and ssize_t were conflicting with gcc builtins
- some stdint types were used in libpayload but not defined
in our stdint.h
With this patch it's possible to compile libpayload with the
reference toolchain again.
Change-Id: Idd5ccfdd9f3536b36bceca2d101e7405883b10bc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2903
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
libcbfs was using printf for size_t typed variables. However, printf
did not support printing those. This patch fixes the issue, removing
the warning when compiling ram_media.c
libcbfs/ram_media.c:52:10: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
libcbfs/ram_media.c:52:10: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat]
Change-Id: Iaf6e723f9a5b0a61a39d3125036fee9853e37ba8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2904
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The keyname() and termname() functions were creating a whole lot of warnings of
the style
curses/PDCurses-3.4/pdcurses/keyname.c:41:9: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
This patch fixes them.
Change-Id: Iae3c4e5201b48c2d2033cac48577e0462a34f309
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2905
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
PDCurses has a function called overlay() and also uses
overlay as a variable name in some functions.
This patch fixes the ambiguity that caused warnings like
curses/PDCurses-3.4/pdcurses/overlay.c: In function '_copy_win':
curses/PDCurses-3.4/pdcurses/overlay.c:51:39: warning: declaration of 'overlay' shadows a global declaration [-Wshadow]
In file included from curses/PDCurses-3.4/curspriv.h:16:0,
from curses/PDCurses-3.4/pdcurses/overlay.c:3:
curses/PDCurses-3.4/curses.h:1014:9: warning: shadowed declaration is here [-Wshadow]
Change-Id: I907653df0c8bb32c98bdcbc6476e94d2da6e0e90
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2906
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Xinitscr is only used internally in PDCurses, unless XCURSES
is defined. This patch fixes a warning that is produced because
of that.
Change-Id: I211f75717276cf028e0b435f328d1687d3536eb7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2907
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The function dump_qh() was added a while back but never used.
Hide it behind USB_DEBUG so it doesn't cause warnings when not
debugging the USB stack.
Change-Id: Idb3c7bb214895ef82676d181836a578bf161e8e0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2909
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
PDcurses is already default. Hence drop the additional attempt
that is not supported by Kconfig.
Config.in:123:warning: defaults for choice values not supported
Change-Id: I12cb5ea0bef2f146cf237c7a3cc9293a600d736b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2902
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Paul Menzel