After the patch [...] The line length is still below 80 characters.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Torsten Duwe <duwe@lst.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3045 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Straight from the data sheet, not tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
exactly the same ID. Improve model number printing.
Add EN29F002(A)(N)B support while I'm at it.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Markus Boas <bios@ryven.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(JEP106W), adds some device IDs and provides information about
non-conforming IDs.
The EON change is left to the patch adding EON chips.
This patch should have no effect on code generation.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
page size. Fix that. Page size is uniform 256 bytes for SPI.
A sector/block size field in struct flashchip would be nice, though.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
output is specified.
Pretty-print the chip status register (including block lock information)
for ST M25P family and Macronix MX25L family chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M25P64, M25P128 to flashrom. ST M25P80 support is already there.
Not tested, but conforming to data sheets and double checked.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7). That way, you only have to
take a short look at the data sheet and choose the right function by
appending the opcode listed in the data sheet.
No functional changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2995 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Attached is a patch that enables AMD Geode CS5536 chipset support. I
have tested it successfully on a MSM800 board from digital logic.
Signed-off-by: Lane Brooks <lbrooks@mit.edu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a delay of 10 us after entering ID mode and this was insufficient for
the 29C020. The data sheet claims we have to wait 10 ms, but tests have
shown that 20 us suffice. Allow for variations in chip delays with a
factor of 2 safety margin.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add support for the Fujitsu MBM29F400TC flash part.
Detection and reading works, writing is not tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2903 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Looking through the sources of Uniflash utility I found that this chip
is no more no less than low-voltage variant of Am29F040B but with
different ID.
So I created a very quick patch (attached).
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2897 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
status register instead.
This has been tested by Harald Gutmann <harald.gutmann@gmx.net> with a
MX25L4005 chip.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2876 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip the code was tested and verified with is the Macronix MX25L4005,
but other chips should work as well.
Timeouts are still hardcoded to data sheet maxima, but the status
register checking code is already there.
Thanks to Harald Gutmann for the initial code on which this is loosely
based.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Install binary in /usr/sbin (not /usr/bin), as it's a root-only tool.
- Rename manpage from flashrom.1 to flashrom.8, as section 8 contains
"System administration commands (usually only for root)".
- Actually install the manpage upon 'make install'.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2866 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Michael van der Kolff <mvanderkolff@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Move SPI code out of board_enable.c where it started its life. The SPI
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2858 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chip finding and SPI chip accessor code is moved as well. This can be
split later if we feel like it.
The non-use of svn cp is intentional because the only history we'd have
to preserve are a few commits which were early prototypes of chip
identification code. For those who intend to look at that history, they
can look at board_enable.c revision 2853.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2857 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The help implied that writes happen by default, which they don't. Fix
the text, and say something when we dont specify any commands.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2820 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
way. It introduces a generic SPI host driver for the IT8716F Super I/O
which will enable easy SPI programming without having to care for the
peculiarities of the SPI host.
To activate probing for the IT8716F, you have to use the gigabyte:m57sli
mainboard override. SPI support will then use the gathered SPI host data
to access the SPI flash.
This has been tested sucessfully by Ward Vandewege <ward@gnu.org> on the
GA-M57SLI v2.0, which has a MX25L4005 SPI flash part.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2817 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to ITE IT8716F Super I/O. Right now this is hardcoded to the Gigabyte
M57SLI board. It works only with rev 2.0 of the board, but it will bail
out on earlier versions, so no damage can occur.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm self-ack'ing this, as the origin of the code in udelay.c (and thus
the license and copyright owner) is pretty clear.
The code which is now in udelay.c was split out from flash_rom.c in r1428,
and flash_rom.c, in turn, has been around since the beginning and had a
'Copyright 2000 Silicon Integrated System Corporation' line as well as the
usual GPLv2-or-later license header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2767 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
project (being packaged by distros, among other things).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2764 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No changes in content of the files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2751 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan Reinauer