- Add missing entry for the NIC:
device pci 0f.0 on end # Ethernet (onboard)
- Drop the following lines:
register "com1" = "{115200}"
register "com2" = "{38400}"
Those entries hardcode the BAUD rate (as far as I can tell, please
correct me if I'm wrong). We don't want that -- instead the config option
TTYS0_BAUD in Options.lb should be used(?) I verified that dropping those
lines will not break serial output (COM1, 115200, 8n1).
- Enable IDE (PCI device 00:12.2) and add the following register lines
to tell the CS5530 code to actually enable IDE channel 0:
register "ide0_enable" = "1"
register "ide1_enable" = "0" # Not available/needed on this board
Tested with a 2.5" hard drive and FILO, works fine.
- Enable USB (PCI device 00:13.0), not sure why it was commented.
- Enable COM2 as it's used by the smartcard reader.
- Add CONFIG_COMPRESSED_PAYLOAD_LZMA to Options.lb, in order to fix
abuild for this board.
- Add some more comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
make them const before putting them into the read-only segment...
(trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2892 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
assumes a 1MB rom chip.
Hence the default position for the VGA bios should also assume a 1MB rom chip,
not a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2887 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2882 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
since it is still our most wide-spread codebase.
The patch is pretty trivial, and nobody except Torsten even looked at
it in a week, so....
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
serious issue, so I am self-acking.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2879 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
days on a function named pll_reset that, on exit, says "Done
cpuRegInit", and which, in turn, made me think it was a lot farther
along that it was.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2878 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
case of keyboard failure (the keyboard initialization was never hit).
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2869 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This has not been working at all until now. With this fix, keyboard,
mouse, parallel port, and the Super I/O sensors work fine (tested
on actual hardware).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
replacing it with a minimal, but working, framework which will be expanded.
Drop a bunch of useless and duplicated files, add missing license headers.
I'm self-acking it this time, the diff is a huge unreadable mess and the old
code is broken anyway...
This code is tested to build fine, and can boot a Linux kernel up to a
login-prompt via FILO (IDE). This is verified on actual hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2859 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2856 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Without this bugfix, the resource for the PCI/ISA video memory at
0xa0000 - 0xbffff is too big, i.e. it goes up to 0xcffff instead of
just 0xbffff as it should.
Here's the diff from two runs of the tool from
http://www.linuxbios.org/pipermail/linuxbios/2007-June/022449.html
on the MSI MS-7260 (K9N Neo), with and without the bugfix. After applying,
the resource size is correct again.
--- dumpres_lb_pci_vgacard_without_resfix.txt
+++ dumpres_lb_pci_vgacard_with_resfix.txt
@@ -11,7 +11,7 @@
MMIO map: #2 0x0000000000 - 0x000000ffff Access: / Dstnode:0 DstLink 0
MMIO map: #3 0x0000000000 - 0x000000ffff Access: / Dstnode:0 DstLink 0
MMIO map: #4 0x0000000000 - 0x000000ffff Access: / Dstnode:0 DstLink 0
-MMIO map: #5 0x00000a0000 - 0x00000cffff Access: R/W Dstnode:0 DstLink 0
+MMIO map: #5 0x00000a0000 - 0x00000bffff Access: R/W Dstnode:0 DstLink 0
MMIO map: #6 0x00fc000000 - 0x00fd1fffff Access: R/W Dstnode:0 DstLink 0
MMIO map: #7 0x00fd200000 - 0x00fd1fffff Access: R/W Dstnode:0 DstLink 0
MMIO map: #0 0x000000 - 0x003fff Access: R/W ISA VGA Dstnode:0 DstLink 0
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2853 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
use that feature in order to not waste RAM.
Also, add missing CONFIG_VIDEO_MB for the eaglelion/5bcm, which should
fix the build for that board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2848 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
currently don't have it but need it to compile with the new Geode GX1
VGA support. This sets the size at 4MB, which was the size previously
defined in the VGA code.
Signed-off-by: Corey Osgood <corey.osgod@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
See http://www.linuxbios.org/BCOM_WINNET100_Build_Tutorial for hardware
description and build tutorials.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This makes sense on systems with small memories when the VGA feature is
not used (CONFIG_VIDEO_MB = 0 in this case).
On Geode GX1 based systems the following amount of memory should be reserved
when VGA support is enabled:
- 1MiB for VGA and SVGA resolutions
- 2MiB for XGA resolution
- 4MiB for SXGA resolution
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2840 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while I'm at it (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801DB to reset. See this thread for more info:
http://article.gmane.org/gmane.linux.bios/26791
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is platform specific.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2810 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes the problems with PCI add-on cards not being detected or
initialized on MCP55-based systems (PCI bridge decoding change).
I have tested this on the MSI MS-7260 (K9N Neo) with a PCI VGA card,
which worked fine in any of the three PCI slots.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reported by Robert Millan.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is tested with abuild so shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2800 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence the default position for the VGA bios should also assume a 1MB rom chip, instead of a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For example: in C51/MCP55 or C51/MCP51
Will allow
1. C51 at 0x10 to 0x14, and MCP at 0 to 4
2. C51 at 1 to 4, and MCP at 7 to 0x0a
The reason is c51/mcp51/mcp55 reported unitid is 0x0f (far beyond it
needed), and will prevent us from putting them on bus 0.
Typical values for c51/mcp55 or c51/mcp51:
HT_CHAIN_UNITID_BASE = 0x10 # for C51
HT_CHAIN_END_UNITID_BASE = 0 # for mcp
If only have mcp with c51,
HT_CHAIN_UNITID_BASE = 0 # for MCP
#HT_CHAIN_END_UNITID_BASE = 0 # default value 0x20
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mostly undocumented, had a broken coding style, contained lots of dead
code and had several other problems, e.g. it enabled write access to the
ROM (why?), it unconditionally enabled primary/secondary IDE (which should
have a config option) and that even _twice_ (which is um... wrong).
The new code
- has 'ide0_enable' and 'ide1_enable' config options (which actually
work) to enable/disable the primary/secondary IDE interface in
Config.lb.
- Does _not_ enable write access to the ROM (or is there some good
reason to do that? If so, it should at least have a config option).
- Contains a bit more documentation.
- Uses readable (and documented) #defines instead of hardcoded magic values.
- aaand... it actually compiles ;-) Yep, that's right. The previous code
wouldn't even build, as it hadn't been fully ported from v1 (still used
v1 functions which are simply not available in v2).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Please fix this if you can.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2774 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(or at least most) mainboards. This should put and end to
copy-paste'ing the same file again and again for every mainboard.
Fix the build for the MSI MS-6178 target (wrong location of the common
failover.c file).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2772 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Removed reset.c and added copyright headers.
Remove debug.c. It is not used and should not be here.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2766 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann