The new API is in use in depthcharge and is based around the "i2c_transfer"
function instead of i2c_read and i2c_write. The new function takes an array of
i2c_seg structures which represent each portion of the transfer after a start
bit and before the stop bit. If there's more than one segment, they're
seperated by repeated starts.
Some wrapper functions have also been added which make certain common
operations easy. These include reading or writing a byte from a register or
reading or writing a blob of raw data. The i2c device drivers generally use
these wrappers but can call the i2c_transfer function directly if the need
something different.
The tegra i2c driver was very similar to the one in depthcharge and was simple
to convert. The Exynos 5250 and 5420 drivers were ported from depthcharge and
replace the ones in coreboot. The Exynos 5420 driver was ported from the high
speed portion of the one in coreboot and was straightforward to port back. The
low speed portion and the Exynos 5250 drivers had been transplanted from U-Boot
and were replaced with the depthcharge implementation.
BUG=None
TEST=Built and booted on nyan with and without EFS. Built and booted on, pit
and daisy.
BRANCH=None
Original-Change-Id: I1e98c3fa2560be25444ab3d0394bb214b9d56e93
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193561
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Jimmy Zhang <jimmzhang@nvidia.com>
Original-Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 00c423fb2c06c69d580ee3ec0a3892ebf164a5fe)
This cherry-pick required additional changes to the following:
src/cpu/allwinner/a10/twi.c
src/drivers/xpowers/axp209/axp209.c
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I691959c66308eeeec219b1bec463b8b365a246d7
Reviewed-on: http://review.coreboot.org/7751
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
BOOT_MEDIA_SPI_BUS is a Kconfig variable used on some ARM-based
platforms to set up CBFS media. It turns out it can also be helpful
for setting up the eventlog which is intended to reside on the same
SPI flash as CBFS. Setting it for x86 will allow us to remove an
assumption about which SPI bus is used for this flash device.
Long term this can go away as we come up with a better abstraction
for the eventlog's backing store. This is only intended to help us
get from here to there.
BUG=none
BRANCH=none
TEST=built and booted on Link
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I1d84dc28592fbece33a70167be59e83bca9cd7bc
Original-Reviewed-on: https://chromium-review.googlesource.com/191202
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 200aa7c5b1b1f4c74412893cf7231a12e2702463)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: If988bcff5244ec6a82580203471b25fac49c45ef
Reviewed-on: http://review.coreboot.org/7752
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This replaces a hard-coded bus number of 0 with a Kconfig variable,
CONFIG_BOOT_MEDIA_SPI_BUS. This removes an assumption made for x86
where this value is always 0 and makes it easy to add support for
other platforms where the bus number for the backing SPI flash is
more arbitrary.
BUG=none
BRANCH=none
TEST=tested on Nyan (bus=4) and Link (bus=0)
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I1e878a1628af7f4ccc2f39a70b2190192767e536
Original-Reviewed-on: https://chromium-review.googlesource.com/194854
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 371c6c14d8d4b98004eebce7049a88a219682bc4)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ie105b4654e028098f2137c96e4309b8d85f096df
Reviewed-on: http://review.coreboot.org/7753
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This symbol is set using a config variable which can be set to something
appropriate by the SOC. If it isn't, the symbol is set to 0 which should be
caught by checks in the cbmem console itself.
BUG=None
TEST=Built for nyan with a cbmem buffer location set. Built for peach_pit
without a location set.
BRANCH=None
Original-Change-Id: I92cd65bb6767a67637faf1dd3cdbe03e433724a9
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193165
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 4f38c073bfe469a753e168391787fdd7bc5c34d9)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I979037fe8cda885cc516d79f3151ca1fc77adca3
Reviewed-on: http://review.coreboot.org/7746
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Turns out that when you clear 28 bits starting with bit 3, you leave bit
31 standing. Ooops...
This shouldn't really matter since that bit is reserved/SBZ in CLIDR
anyway, but it's still nice to fix it. This whole thing should really be
an AND for clarity anyway in my opinion.
Bug found in upstream NetBSD (who would've thought...).
BUG=None
TEST=Still boots.
Change-Id: Ic826e82d58fd1ce984971afea3dfa9296f746d9f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/193300
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit d270c0ec18b74b272451c456cbf07e99d95896cb)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/7745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order to build rmodules for armv7 boards, the default
compiler options need to be set so the assembler sources
can correclty compile. For now assume rmodules for arm
devices use the ramstage compiler options.
BUG=chrome-os-partner:27094
BRANCH=None
TEST=Built vboot as rmodule for nyan.
Original-Change-Id: I8d12a2a57944b187cbdff2f22176de5b4de87a54
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/190926
(cherry picked from commit cd091ae8ced30e6e2543f36bdb5c14518e7879c3)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I24706f7d72a53f71abd2770f0d12de8c6ed31f63
Reviewed-on: http://review.coreboot.org/7744
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
According to DP version 1.2a, The MOT (Middle-of-Transaction) bit
must be set when the I2C transaction does not stop with the current
AUX transaction.
Thus the correct steps for an I2C read shall be:
1. I2C command write with MOT set to 1
2. I2C command read to the same address with MOT set to 0
BUG=chrome-os-partner:27679
TEST=EDID data read from LP140WH8 panel is correct while it's a
repeated pattern of the first 16 bytes without this CL
BRANCH=none
Original-Change-Id: I0526beffb8852fbbe0eb5bb80e370261617a59b8
Original-Signed-off-by: Ken Chang <kenc@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/194915
Original-Reviewed-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
(cherry picked from commit 466ab0e00744f79ae3720474140d95e5f0828de9)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ic8ad38b4b08989dd7178d59151e1e276b8a58439
Reviewed-on: http://review.coreboot.org/7763
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
PLLD, the clock for display, was previously hard-coded to 306MHz. To support
more different panels, we should calcualte PLLD by panel pixel clock
configuration.
Note existing pixel clock configurations for nyan* boards won't work (they used
to rely on hard-coded approximated values) so the device trees are also
modified.
BRANCH=none
BUG=chrome-os-partner:25933
TEST=emerge-nyan_big coreboot chromeos-bootimage
See panel correctly initialized and got DEV screen.
Original-Change-Id: I8d592f0cc044e7c4e4803c45955642e791210ad3
Original-Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/193565
(cherry picked from commit 4f9b793633ebb2d104b0544e3b72fa0d105951c4)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ib2cabbad60af010e872505e888eab485ba8c2916
Reviewed-on: http://review.coreboot.org/7762
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds a missing dma_release() at the end of DMA transfers. It
probably doesn't matter since we don't do many DMA transfers, though
I wouldn't want to hit some corner case with EFS and eventlog.
BUG=none
BRANCH=none
TEST=tested on nyan
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I79b30455babe75a13aac827caac88bf7053ec9e4
Original-Reviewed-on: https://chromium-review.googlesource.com/194479
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit dc7dc1d25bd88873b4c1198a6f3723d27c914ddc)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I8c5da4e104328fd8bce71942e6eda458a37bfe06
Reviewed-on: http://review.coreboot.org/7761
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It worked earlier since the APB and AHB bus widths occupy the same bits
in their respective registers.
BUG=none
BRANCH=none
TEST=tested on Nyan
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I9b18c648c60dcc4ad62ca1f514d253f8cccaeee7
Original-Reviewed-on: https://chromium-review.googlesource.com/194478
Original-Tested-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 1d912302e9dcc9c6ba69e15434bb1841e1196208)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I2ea7ac83d3501876df52018aed467ec33074817e
Reviewed-on: http://review.coreboot.org/7760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
GPIO_PU4/PH1 and _PU5/PH2 were set to use the same PWM1/2 SFIO.
Even though no problems were caused by this, correct it here
so we get a conflict-free pinmux map.
BUG=chrome-os-partner:27091
BRANCH=none
TEST=Built and booted on Nyan, ran TegraShell "pinmux check"
and saw no conflicts.
Original-Change-Id: Ib16341aa0c92b9a078d7f3254d4151e9592f40b0
Original-Signed-off-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/194582
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit e06a5a62d381f803dd6574787795a51ce1f1fe74)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I055359dc80c0c878ba5f5faac17884a5506a826c
Reviewed-on: http://review.coreboot.org/7759
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
href_to_sync and vref_to_sync are chip specific settings. Currently
they are set to 1/2 of hfront_porch and vfront_porch respectively.
However, to support EDID (CL192730), per David Ung, the safe
values for both are 1 (the same settings as in kernel).
BUG=none
BRANCH=none
TEST=built and booted on nyan.
Original-Change-Id: Ifb8898e720a160ba044e2b526de2a4d17bc63672
Original-Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193504
Original-Reviewed-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Original-Tested-by: Hung-Te Lin <hungte@chromium.org>
(cherry picked from commit a7128a533ba6083ddfeeca3ba0828962cc2c8ab6)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I6954a5b49c798ebdffb20e3ebc9099cd17591b79
Reviewed-on: http://review.coreboot.org/7758
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change takes about 8K of space away from the cbfs cache and repurposes
it for the cbmem console buffer. This is a little more than twice the space
we currently need for the bootblock and ROM stage to give us some room to grow
and for extra debug output if needed.
BUG=None
TEST=Built and booted on nyan. Checked the cbmem output.
BRANCH=None
Original-Change-Id: I6543bf5efddcf2377528a273f846b8090cd8be55
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193169
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 32e9ea6f9ecaa9b5441c91acab96514222f3af2c)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ia9e5cc7a4b561bd89137cdc8b594584b272d9fab
Reviewed-on: http://review.coreboot.org/7757
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Set the appropriate config options and make the appropriate calls
to perform vboot verification. The flashmap offset as well as the TPM
information needs to be properly set. Lastly, call into
vboot_verify_firmware() to perform the vboot verification when it is
enabled.
BUG=chrome-os-partner:27094
BRANCH=None
TEST=Built vboot verification on nyan.
Original-Change-Id: I6113badd6143008ceb2b80f0ec0832e1addd03d7
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/190928
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
Original-Reviewed-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 8c6c48c7823738bf9b029a467b077d2ee20d04e5)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I2a442b1b0fff55e737df2e96740c05c1726502d5
Reviewed-on: http://review.coreboot.org/7743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
RAM module for RAMCODE 0010 (K4B4G1646Q) does not work with
hynix-2GB-204MHz configuration. We need to replace it by
hynix-2GB-792MHz. Also updated hynix-2GB-792MHz configuration
from Nyan board folder. This commit is only for bring up stage.
Once finish dram stress test, will update it again.
BRANCH=none
BUG=chrome-os-partner:27682
TEST=emerge-nyan_blaze coreboot builds OK; flash to blaze board and
boot to kernel successfully
Original-Change-Id: Idfc503c944ac6120c92a4cf329f3fbe63b2c2a1c
Original-Signed-off-by: Neil Chen <neilc@nvidia.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193737
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
(cherry picked from commit 91f21aa0cf9251b825e42d946d8cd41849c57447)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I6293fa638c5b2577e502ba34a3cc6e6d5b7f2fdb
Reviewed-on: http://review.coreboot.org/7742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are some unexpected symbol at the end of each line in the
generated .inc file when the config file is in DOS format (CR+LF).
Modify cfg2inc to support DOS format cfg file by removing carriage return symbols from the end of each line.
BUG=chrome-os-partner:27614
TEST=sudo cfg2inc.sh XXX.cfg # make a expected inc file
BRANCH=nyan
Signed-off-by: Neil Chen <neilc@nvidia.com>
Original-Change-Id: I68b0f4b3805fcb5a6b633653c95afbafcb880a93
Original-Reviewed-on: https://chromium-review.googlesource.com/192697
Original-Tested-by: Neil Chen <neilc@nvidia.com>
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Commit-Queue: Neil Chen <neilc@nvidia.com>
(cherry picked from commit 38e90ab0d9110d3ede39c70e27961b833813a7d4)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I30737600fa8ac12a45ad0fbc6086a624993794e7
Reviewed-on: http://review.coreboot.org/7741
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
For some UART hardware registers are 32 bits wide, so we will need
base_port + reg << 2 instead. Prepare for that change and unification of
MMIO between ARM and x86.
Change-Id: I5fa2c2f7ee4872499a01754c1ba872a8addf499c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7793
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
To set the 8 different BCT as hynix-2GB-204 first. Once the
corresponding BCT release from AE, change it.
BRANCH=none
BUG=None
TEST=emerge-nyan_blaze coreboot builds OK
Signed-off-by: Neil Chen <neilc@nvidia.com>
Original-Change-Id: Ia42a4a5b85c561421ab8ae9aaf21c46a3c0a3513
Original-Reviewed-on: https://chromium-review.googlesource.com/191682
Original-Tested-by: Neil Chen <neilc@nvidia.com>
Original-Reviewed-by: Artiste Hsu <chhsu@nvidia.com>
Original-Reviewed-by: Katie Roberts-Hoffman <katierh@chromium.org>
Original-Commit-Queue: Neil Chen <neilc@nvidia.com>
(cherry picked from commit 27792db4a90ae00e066bb0b88968cf5f187edb1d)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ia648c8bdbbbc82bbc8508bead6ab24d8d0aa3fb2
Reviewed-on: http://review.coreboot.org/7740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The EC doesn't seem to be able to handle its bus running at 4 MHz or higher.
To avoid it not being able to keep up, we reduce the frequency of that bus on
all nyan derivatives to 3 MHz. Because PLLP can't be divided that low, we
switch the clock source to CLKM.
BUG=chrome-os-partner:22849
TEST=Built and booted on nyan.
BRANCH=None
Original-Change-Id: I8f31b41098d64634427b4686f5333012f643fada
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193349
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit c215c50a5bb982b0e671c951e2fe8df06db85db2)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ia60513d118aed8881927e9d52f170e27655ea8e7
Reviewed-on: http://review.coreboot.org/7739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Consolidate the register setting clrsetbits_le32 call to simplify the macros.
Add a check for bits of the divisor being dropped. The clock source registers
will throw away bits that aren't supported, so we can check for divisor
overflow by checking for dropped bits.
BUG=None
TEST=Purposefully tried to set a clock to a rate which overflows its divisor.
Verified that the check triggered. Booted on nyan. Verified the TPM i2c bus
frequency was still correct.
BRANCH=None
Original-Change-Id: I3b1b6ba57f6b7729f303d15a16b685a48751d41f
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193348
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 9cd79dd974d8a3c31398f8fbd62750b194867891)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Id4d8ecfeff52737cdd68999028b37cbdedb0d116
Reviewed-on: http://review.coreboot.org/7738
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
To ensure that the command1 write which sets the "go" bit completes before
other reads to the device. Otherwise, there's a race condition where those
register values might still have their values from the last transfer. With
different SPI clock frequencies, that could lead to spi_delay being told there
were negative bytes still to send. Its expected delay would wrap to a negative
value, that was passed to udelay, and the system would sit there for 4 seconds
not doing anything.
BUG=None
TEST=Built and booted on nyan. Set the SPI bus frequency to a value which was
causing the 4+ second delay and verified that it no longer happened.
BRANCH=None
Original-Change-Id: I8b4090efc69f34d0413e3f63c59c1825dd151cec
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193347
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit d7ea9febdf2c5942f81607ee6ded786c9a8954bb)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I095bfc745eda37b8e666475ceb41684152f3709a
Reviewed-on: http://review.coreboot.org/7737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes two problems with the clock configuration on tegra124. First, the
macro which set up the i2c clocks tried to account for the fact that the i2c
divisor's lsb represents 1.0 where it normally represents 0.5 by multiplying
the target frequency by 2. That doesn't work, unfortunately, because the
divisor is actually n + 1, and what n + 1 means depends on where the one's
place is in the divisor.
Also, when calculating the divisor, the standard C division operator uses
truncation to deal any remainder which tends to make the divisor smaller. That
has the effect of making the output frequency higher than what was requested.
Since it's usually safer to undershoot a frequency than overshoot it, this
change makes those divisions round up instead.
Finally, the hand tuned temporary UART clock configuration was adjusted so
that it still ends up with the same divisor. Without that, very early output
from the bootblock is garbled, specifically the coreboot welcome banner,
build timestamp, etc.
BUG=chrome-os-partner:27220
TEST=Built and booted on nyan. Used a logic analyzer to verify that the TPM
i2c bus ran at 400KHz instead of 660KHz, and that the divisor was the expected
value. Measured boot time with and without EFS and verified that there was no
change. Spot checked the output for errors and verified that none of the
bootblock output was garbled.
BRANCH=None
Had to add the stdlib.h from 89ed6c that hadn't been merged correctly.
Original-Change-Id: I7e948c361ed4bf58c608627d32f2e3424faea1fb
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/193362
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 164f7010a47d3bbdbc8bb572106140ae186f3807)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I317b66eda929c0e5a5832adca267b8b54c6aae34
Reviewed-on: http://review.coreboot.org/7736
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
To read EDID, we need to access I2C via DP AUX channel.
BRANCH=none
BUG=chrome-os-partner:25933
TEST=emerge-nyan coreboot chromeos-bootimage
Original-Change-Id: I2666b5d46843485b79265a537f19bd8eab5e1a26
Original-Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/188858
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 8f8e98ff5038b57f89332aee75573095c3933dd2)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I5b1b6ab2940c8265483059fd94a2c4db2a41144a
Reviewed-on: http://review.coreboot.org/7735
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If EFS is enabled and vboot didn't tell us it's going to use the display, we
can skip initializing it and save some boot time.
BUG=chrome-os-partner:27094
TEST=Built and booted on nyan without EFS in recovery mode and normal mode.
Built and booted on nyan with EFS in recovery mode and normal mode. Verified
that in normal mode with EFS the display initialization was skipped and boot
time was essentially the same as when display initialization was simply
commented out.
BRANCH=None
Original-Change-Id: I1e2842b57a38061f40514407c8fab1e38b75be80
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/192544
Original-Reviewed-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit a672d18c3570e6991a1c1c0089697112a4cd71d0)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I95e8bd7a447876174305f755cc632365ed6f5a30
Reviewed-on: http://review.coreboot.org/7734
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
A leading double slash can result when $DESTDIR/$TARGETDIR is expanded
in the libelf portion of buildgcc. The leading double slash causes buildgcc to fail when run from Windows/Msys2. Replace $DESTDIR/$TARGETDIR
with $DESTDIR$TARGETDIR to avoid the problem.
Change-Id: Ide2bae41c07c1566f80104c3a2e2acab53de0d17
Signed-off-by: Scott Duplichan <scott@notabs.org>
Reviewed-on: http://review.coreboot.org/7788
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
It appears the decimal value was used instead of the hex value.
Change-Id: I04acde9e5b2a9e08ed01b0564c3d561b0385a392
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/7799
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The doxygen directory is created by running 'make doxygen' - this
results in a huge number of new files that swamps graphical git tools.
Since this directory is a product of a build, it should be safe to
ignore.
Change-Id: I871dd2a36433d4dd46b231ebc7398e85d0278f27
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/7798
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
For some of the boards using AMD processors, the Agesa Makefile.inc
is processed twice, causing the list of obj files passed to the ar
command to be added twice. This does not break the build, but does
make the ar command line unnecessarily long.
Change-Id: I02a7e6fc617e337ca2e2dceeff3d4db9995bfe16
Signed-off-by: Scott Duplichan <scott@notabs.org>
Reviewed-on: http://review.coreboot.org/7787
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
powernow_acpi.c array TDP has 20 entries, yet the loop that reads it
processes 21 entries. This causes a gcc 4.9.2 build failure. Limit
processing to 20 entries.
Change-Id: Ice173b276293184386cd8943a3213f3154f86458
Signed-off-by: Scott Duplichan <scott@notabs.org>
Reviewed-on: http://review.coreboot.org/7791
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Too many false positives, not useful enough for us at the moment
at the cost of not having the whole tree build without warnings
as errors.
Change-Id: I9f9910b7f66ebf3a82d42e7732e413ba27dbbbe7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7778
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Remove '__attribute__((optimize("Os")))' as it is unlikely to be
necessary as it is not used in other families that have the same
code and only hides deeper issues.
Change-Id: Ica890812ebc2fb659b9c3e46b40cf3f6534b3cf2
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/7689
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
It's not useful in quiet mode, and is very distracting.
Change-Id: I59dc8caa22b66980560d5afb76eae801efaa29ad
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/124
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
The updated KaveriPI binary, upgrading to v1.1.0.7, requires changes
to define the PSP device (PCI 0:08.0) and the IOMMU device (PCI 0:00.2).
In the new AGESA binary, the IOMMU device is enabled and must be
disabled in devicetree.cb and agesawrapper_amdinitenv() to maintain
the same level of functionality.
Change-Id: I3f47e0bd5a75729ec1e4b7b11885d0622c474342
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/7727
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
We already have aarch64 targets. Extend the "all" target.
Change-Id: I74d9bf5123695318c15b73c89f170f3ebb20aa80
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7729
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Clang complains:
"implicit truncation from 'int' to bitfield changes value from -1 to 15"
-1 is define in 'c11std 6.3.1.3p2' as:
[Signed and unsigned integers] Otherwise, if the new type is unsigned,
the value is converted by repeatedly adding or subtracting one
more than the maximum value that can be represented in the new type
until the value is in the range of the new type.60)
FOOTNOTE.60 The rules describe arithmetic on the mathem...
This is "0xFF" on Mullins and "0xF" in this case. Clang seems to
complain about this two's complement in a bitfield as being truncated.
As the bitfield is 4 bits wide, (a maximum of 15 decimal), we set the
field as '0x0F'. Ideally this field /should/ be set to 'UINT8_MAX' however
we still have silly truncation warnings.
Change-Id: Ib7476d453ffd932bb911e638117cf9f56f71f269
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7719
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Clang complains that a signed shift result (0x210000000)
requires 35 bits to represent, but 'int' only has 32 bits.
However, we write the high bits separately and so this is
a spurious warning.
Change-Id: I3e1c57334077feb50004d7b39abff4bd84ca095b
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7673
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
- add a 'quiet' mode that only prints important messages
- add vendor/mainboard to all strings printed
With quiet on, multithreaded looks like this:
skipping google/storm because we're missing compilers for (arm armv4 armv7)
iwill/dk8_htx built successfully. (took 5s)
jetway/j7f2 built successfully. (took 6s)
iwill/dk8x built successfully. (took 8s)
iwill/dk8s2 built successfully. (took 8s)
jetway/j7f4k1g5d built successfully. (took 10s)
With quiet off, single threaded now looks like this:
Building intel/emeraldlake2
Creating config file for intel/emeraldlake2...
intel/emeraldlake2 (blobs, ccache)
intel/emeraldlake2 config created.
Compiling intel/emeraldlake2 image...
intel/emeraldlake2 built successfully. (took 5s)
And quiet off multithreaded looks like this:
Building iwill/dk8_htx
Creating config file for iwill/dk8_htx...
iwill/dk8_htx (blobs, ccache)
intel/mohonpeak config created.
Compiling intel/mohonpeak image on 1 cpu...
intel/minnowmax config created.
--- snip ---
intel/mtarvon built successfully. (took 4s)
Building iwill/dk8s2
Creating config file for iwill/dk8s2...
iwill/dk8s2 (blobs, ccache)
intel/mohonpeak built successfully. (took 5s)
Building iwill/dk8x
Change-Id: Ib7b9a625d77bb8e0663afc00d7133e415866ecec
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/7716
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
They were only used internal to the SPI drivers and, according to the comment
next to their prototypes, were for when the SPI controller doesn't control the
chip select line directly and needs some help.
BUG=None
TEST=Built for link, falco, and rambi. Built and booted on peach_pit and nyan.
BRANCH=None
Original-Change-Id: If4622819a4437490797d305786e2436e2e70c42b
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/192048
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 1e2deecd9d8c6fd690c54f24e902cc7d2bab0521)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ida08cbc2be5ad09b929ca16e483c36c49ac12627
Reviewed-on: http://review.coreboot.org/7708
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
spi_set_speed was never implemented, and spi_cs_is_valid was only implemented
as a stub and never called.
BUG=None
TEST=Built for rambi, falco, and peach_pit.
BRANCH=None
Original-Change-Id: If30c2339f5e0360a5099eb540fab73fb23582905
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/192045
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 98c1f6014c512e75e989df36b48622a7b56d0582)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Iebdb2704ee81aee432c83ab182246d31ef52a6b6
Reviewed-on: http://review.coreboot.org/7707
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
The SPI drivers for tegra and exynos5420 have code in them which waits for a
frame header and leaves filler data out. The SPI driver shouldn't have support
for frame headers directly. If a device uses them, it should support them
itself. That makes the SPI drivers simpler and easier to write.
When moving the frame handling logic into the EC support code, EC communication
continued to work on tegra but no longer worked on exynos5420. That suggested
the SPI driver on the 5420 wasn't working correctly, so I replaced that with
the implementation in depthcharge. Unfortunately that implementation doesn't
support waiting for a frame header for the EC, so these changes are combined
into one.
BUG=None
TEST=Built and booted on pit. Built and booted on nyan. In both cases,
verified that there were no error messages from the SPI drivers or the EC
code.
BRANCH=None
Original-Change-Id: I62a68820c632f154acece94f54276ddcd1442c09
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/191192
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 4fcfed280ad70f14a013d5353aa0bee0af540630)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Id8824523abc7afcbc214845901628833e135d142
Reviewed-on: http://review.coreboot.org/7706
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <gaumless@gmail.com>
Depending on the platform the underlying regions vboot requires
may not be accessible through a memory-mapped interface. Allow
for non-memory-mapped regions by providing a region request
abstraction. There is then only a few touch points in the code to
provide compile-time decision making no how to obtain a region.
For the vblocks a temporary area is allocated from cbmem. They
are then read from the SPI into the temporarily buffer.
BUG=chrome-os-partner:27094
BRANCH=None
TEST=Built and booted a rambi with vboot verification.
Original-Change-Id: I828a7c36387a8eb573c5a0dd020fe9abad03d902
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/190924
Original-Reviewed-by: Hung-Te Lin <hungte@chromium.org>
(cherry picked from commit aee0280bbfe110eae88aa297b433c1038c6fe8a3)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Ia020d1eebad753da950342656cd11b84e9a85376
Reviewed-on: http://review.coreboot.org/7709
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The arm architecture currently exports cache_sync_instructions()
in <arch/cache.h>. In order for rmodule loading to work on arm
architectures the cache_sync_instructions() needs to be called to
sequence the instruction cache. To avoid sprinkling #ifdefs around
just add an empty cache_sync_instructions() definition.
BUG=chrome-os-partner:27094
BRANCH=None
TEST=Built and booted nyan and rambi.
Original-Change-Id: I1a969757fffe0ca92754a0d953ba3630810556e3
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/191551
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit fda20947b928ee761d5ed15e414636af419970a6)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I3e8ca12e1d82ccedf1ff9851ae3c5c80cda2dd5f
Reviewed-on: http://review.coreboot.org/7710
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
TEST=Booted nyan in normal and recovery mode. Created a map, filled it with some
chars, then verified they can be read from the pointer returned.
BUG=chrome-os-partner:25587
BRANCH=None
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: Id1f1be4f6d2d5734d87bf3452d4806d0fe3fda88
Original-Reviewed-on: https://chromium-review.googlesource.com/188894
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Daisuke Nojiri <dnojiri@chromium.org>
Original-Tested-by: Daisuke Nojiri <dnojiri@chromium.org>
(cherry picked from commit 7fda3885f51c8d383585a80e99ab3df9c789d872)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I6255d11396c87f40b0ae12ceab0fd152f2478529
Reviewed-on: http://review.coreboot.org/7658
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Use the SPSR to extract and inject CPSR values when an exception happens and
pass that information to exception hooks.
The register structure GDB expects when using its remote protocol has a spot
for the CPSR.
BUG=None
TEST=Built and booted on link, nyan.
BRANCH=None
Original-Change-Id: Id950fb09d72fb0f81e4eef2489c0849ce5dd8aca
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/180253
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 8e7014f24a580f84c91fa7b0369dfa922918adcc)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I49357fb6a65edeff7a9a48d54254308a6b0efdb7
Reviewed-on: http://review.coreboot.org/7657
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To support a GDB stub, it will be necessary to trap various exceptions which
will be used to implement breakpoints, single stepping, etc.
BUG=None
TEST=Built and booted on Link with hooks installed and saw that they
triggered when exceptions occurred. Built and booted on nyan.
BRANCH=None
Original-Change-Id: Iab659365864a3055159a50b8f6e5c44290d3ba2b
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/179602
Original-Reviewed-by: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 8db0897b1ddad600e247cb4df147c757a8187626)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: I5e7f724b99988cd259909dd3bd01166fa52317ec
Reviewed-on: http://review.coreboot.org/7656
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To find the coreboot tables, the payload has historically searched for their
signature in a predefined region of memory. This is a little clumsy on x86,
but it works because you can assume certain regions are RAM. Also, there are
areas which are set aside for the firmware by convention. On x86 there's a
forwarding entry which goes in one of those fairly small conventional areas
and which points to the CBMEM area at the end of memory.
On ARM there aren't areas like that, so we've left out the forwarding entry and
gone directly to CBMEM. RAM may not start at the beginning of the address space
or go to its end, and that means there isn't really anywhere fixed you can put
the coreboot tables. That's meant that libpayload has to be configured on a
per board basis to know where to look for CBMEM.
Now that we have boards that don't have fixed amounts of memory, the location
of the end of RAM isn't fixed even on a per board level which means even that
workaround will no longer cut it.
This change makes coreboot pass the location of the coreboot tables to
libpayload using r0, the first argument register. That means we'll be able to
find them no matter where CBMEM is, and we can get rid of the per board search
ranges.
We can extend this mechanism to x86 as well, but there may be more
complications and it's less necessary there. It would be a good thing to do
eventually though.
BUG=None
TEST=Built and booted on nyan. Changed the size of memory and saw that the
payload could still find the coreboot tables where before it couldn't. Built
for pit, snow, and big.
BRANCH=None
Original-Change-Id: I7218afd999da1662b0db8172fd8125670ceac471
Original-Signed-off-by: Gabe Black <gabeblack@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/185572
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Gabe Black <gabeblack@chromium.org>
Original-Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit ca88f39c21158b59abe3001f986207a292359cf5)
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Iab14e9502b6ce7a55f0a72e190fa582f89f11a1e
Reviewed-on: http://review.coreboot.org/7655
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Gabe Black