Unset devicetree options already default to zero. Note that this setting
is not referenced anywhere else, and will be removed in a follow-up.
Change-Id: I7bcc1c66caa9167c2327e1dc782f69c5de0fac2e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48579
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SMIs and SCIs aren't used before ramstage or the OS, so there should be
no need to already set them up in romstage. Not using this GPIO
configuration functionality allows untangling the GPIO and smi_util code
and only linking smi_util in ramstage in follow-up patches. In romstage
the pins get initialized as inputs with pull-up, so that at least that
part still matches the configuration before this patch.
BUG=b:175386410
Change-Id: I733bb91ef60dc66093781a376a2e9837f5209671
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
1. Make CLKSRC -> 7 and CLKREQ -> 6
2. CLK 6 is using free running CLK
3. Make LAN CLK 7 as unused as GbE is disable
TEST=Able to detect PCIE SD card on 0x1 slot.
Change-Id: I7fbde9492a0c59fc76931bfb7c9522d4f208ebb0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48449
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is a whole bunch of pads being configured by the vendor firmware
that are either unconnected due to unpopulated resistor pads, only
connected to test points for vendor debugging purposes or just used as
strap. Configure them as NC with an appropriate pull to disable the
RX/TX functions.
The pads have been determined by dissecting a dead board.
This patch has been tested thoughroughly on a machine, normally used
productive, to see if any issues arise. No problems occurred at all.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I06b942e3182469f87e41914c893e5b485ccca420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Move the manual calls to fw_config_probe() into the devicetree; the
AUDIO probe is trivial, and the TCSS devices (DMA0, iTBT RP0 & RP1) are
already guarded with probe statements in the baseboard devicetree, so
the code in romstage.c was redundant. The variants seem to have their
USB4 probe statements correct as well, so the manual UPD setting in
mainboard.c was also unnecessary.
BUG=none
TEST=abuild google/volteer
Change-Id: I1d067ff3d181b152c784634ff99202bb2b9202f7
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In cases when a volteer device is unprovisioned, the safest thing to do
for GPIOs that will normally be used for audio codec buses is to leave
them disabled (configured as PAD_CFG_NC). This patch adds support for
that.
BUG=none
TEST=add debug print to new if branch; remove fw_config from CBI and
see print on console
Change-Id: I8efd101174f6e3d7233d2bf803b680673cada81a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47972
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On Delta Lake DVT, dump GPIO settings from UEFI firmware for new PCH
(C621A) by util/inteltool and generate the header file by util/intelp2m.
The DVT and EVT GPIO configurations are the same.
The initial value of GPP_B20 (POST complete) should be high, otherwise
BIC would get incorrect sensor readings and see events like PCH prochot.
Tested=On OCP Delta Lake DVT, dump GPIO configurations
by Intel ITP and verify the results match with the header file.
Change-Id: Ic9837a22bc231a4cb919de316ff6f6ee88411ab8
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47229
Reviewed-by: Tim Chu <Tim.Chu@quantatw.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct IOM setting and TCSS AUX setting to fix type C C0 port display can't output after flip.
BUG=b:173093980
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS, test USB function normally.
Change-Id: I827a2d8a5b01dce412b4170fde0f638670ab8baf
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BT_DISABLE_L (GPP_A13) has to asserted in early_gpio_table to reset
bluetooth on reset.
BUG=b:171085081
TEST=volteer2 boots; scope shows assertion of the signal
Change-Id: Iaa5799e9cab69c074b7920604c8a6c85ad07358a
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This allows factoring out the common initialization for the integrated
UARTs.
Change-Id: I7399a13b9280b732086c6f8e6dfd9f1207d8c8ff
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48508
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently it's not possible to add multiple graphics driver into
one coreboot image. This patch series will fix this issue by providing
a single API that multiple graphics driver can use.
This is required for platforms that have two graphic cards, but
different graphic drivers, like Intel and Aspeed on server platforms or
Intel and Nvidia on consumer notebooks.
The goals are to remove duplicated fill_fb_framebuffer(), to advertise
multiple independent framebuffers in coreboot tables, and better
runtime/build time graphic configuration options.
Add an implementation in edid_fill_fb that supports registering
multiple framebuffers, each with its own configuration.
As the current code is only compiled for a single graphics driver
there's no change in functionality.
Change-Id: I7264c2ea2f72f36adfd26f26b00e3ce172133621
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Remove unused code that appears to be left over from grunt.
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Id5bdb1c957342d55c5e6378c503b8d90da050601
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48505
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit b0e169ac85 included a few small omissions and typos when
converting 'device pci xx.y' to 'device ref blah' after adding the new
chipset.cb file for TGL. This patch fixes these errors:
1) MIPI camera support requires I2C2 & I2C3 enabled
2) Malefor SAR sensor is on I2C2, not I2C3
BUG=b:175165653
TEST=abuild -p none -t google/volteer -x -a -c max
Change-Id: I577957d67f47bbe88bbc2535fb1cb5c8f7390438
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
The xeon_sp ACPI NVS and ramstage NVS were out of sync. Since there
isn't anything uncommon with the soc NVS, use the Intel common NVS.
This covers the NVS cases of common code used by xeon_sp. Update
the mainboards for this change.
Change-Id: Icf422f5b75a1ca7a3d8f3d63638b8d86a56fdd7b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
DPM is a hardware module for DRAM power management and for better
power saving in low power mode.
BUG=none
TEST=Boots correctly on Asurada
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I16b341ad63940b45b886c4a7fd733c1970624e40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46393
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update memory parameters based on memory type supported by
Elkhart Lake CRB:
1. Update spd data for EHL LPDDR4X memory
- DQ byte map
- DQS CPU-DRAM map
- Rcomp resistor
- Rcomp target
2. Add configurations for vref_ca & interleaved memory
3. Add EHL CRB on board LPDDR4X SPD data bin file
4. Update mainboard related FSPM UPDs as part of memory
initialization
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: Ifd85caa9ac1c9baf443734eb17ad5683ee92ca3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Remove JSL specific SMBIOS sku id info as it is not required by
EHL.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: Ib672eb456ba62f2eb7f941630c4fbb34823664f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48123
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
THis patch removes IPU & MIPI related support from EHL CRB as they
are not supported in EHL.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I3eb038009daaabd048f40c7953cb2c111cd4fe63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Since there is no EC support on EHL CRB, this patch removes board
ID detection via EC (board_id.c & board_id.h) and its related
files. Temporarily removes variant_memcfg_config function in
romstage_fsp_param.c, will be added back when updating memory
configs later.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I40d96285dc05ec5faabc123950b6b3728299e99a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48121
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since EHL CRB does not support ChromeOS, this patch removes
ChromeOS EC related headers (ec.h & gpio.h) and #includes.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I9c0c3722065c041769081f3d564646ce6a565a9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Since there is no ChromeOS support for EHL CRB, drop smihandler.c
which just deals with ChromeOS support.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: Id474c3b04a82c03dda6514cc4565b58fb790b9c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Since ChromeOS is not officially supported for EHL CRB, removing
ChromeOS related codes. Here are the change details:
- Remove ChromeOS related kconfig switches, including
SOC_INTEL_CSE_LITE_SKU which has dependency on ChromeOS flag
- Remove chromeos.c file
- Remove ChromeOS dsdt related codes from dsdt.asl & mainboard.c
- Remove ChromeOS GPIO related codes from variants.h & gpio.c
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I4aabd40a4b46d4e64534b99e84e0523eaeaff816
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This is a initial mainboard code cloned entirely from jasperlake_rvp
aimed to serve as base for further mainboard check-ins.
This patch is based on TGL_upstream series patches:
https://review.coreboot.org/c/coreboot/+/37868
List of changes on top off initial jasperlake_rvp clone:
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Replace "jslrvp" with "ehlcrb"
4. Remove unwanted SPD file, add empty SPD as placeholder
6. Empty romstage_fsp_params.c, to fill it later with SOC specific
config
7. Empty GPIO configurations, to be filled as per board
8. Empty memory.c configurations, to be filled as per board
9. Add board support namely BOARD_INTEL_ELKHARTLAKE_CRB
10. Replace jslrvp variant with ehlcrb variant
Changes to follow on top of this:
1. Add correct memory parameters, add SPDs
2. Clean up devicetree as per tigerlake SOC
3. Add GPIO support
4. Update ehl fmd file to replace 32MB chromeos.fmd
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I2cbe9f12468318680b148739edec5222582e42a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch adds support for loading spm firmware from cbfs to spm sram.
Spm needs its own firmware to enable spm suspend/resume function which
turns off several resources such as DRAM/mainpll/26M clk when linux
system suspend.
BUG=b:159079649
TEST=suspend with command `powerd_dbus_suspend` and
wake up the DUT by powerkey
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Change-Id: I6478b98f426d2f3e0ee919d37d21d909ae8a6371
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Follow vendor and enable Advanced Error Reporting for PCIe root ports.
This enabled the Linux AER driver, which handles PCIe error conditions.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9d9b5afca0ca891e2812445db1d42a46ba16199e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48369
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the subsystem ids to PCI ports and devices, which were dumped on
vendor firmware using `lspci`.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Idb36c5c72e1b0b8303439ae5dce772822f551d2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Follow vendor and enable LTR on all root ports to optimize for devices'
latency requirements and also optimize power management while preventing
failure due to wrongly guessing idle states, which happens without LTR.
Tested successfully. No errors show up in dmesg.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8f72087c71e291d2412dc7b3e16ee7f419e2ca0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48367
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All X11 boards currently supported have Intel SPS without support for
S3/S5. Thus, drop it from Kconfig.
Note: not all X11 boards are server boards. When a X11 desktop or
workstation board should be added, this can be selected by the boards,
where S3/S5 work.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ie75c9217078d38c42eba2b30c078b8bb1c2ca694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Correct unconnected pads that are configured different currently by
copying vendor configuration while porting the board.
Add internal pull resistors to all unconnected pads, that do not have an
external pull resistor, to prevent floating.
The pads have been determined by dissecting a dead board. This commit
only changes pads, that are not connected at all and don't have any via,
so we can be absolutely sure there is no other connection.
Change-Id: I991fe270b42f430f7447712236e0f80b3d5bba2a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
(Re)configure various pads found by dissecting a dead board and vendor
firmware, as well as the BMC firmware:
- GPP_B14: input connected to jumper JBR1 - could be used to implement
"BIOS Recovery" ("Top-Block Swap") functionality; external pull-up
- GPP_C20: output to BMC alert CPU_THROTTLED# - can be used to notify
the BMC about a thermal throttling event. Not implemented in vendor
firmware.
- GPP_C23: input connected to the CPU's CATERR# output; external pull-up
Not actively used by vendor firmware.
- GPP_D1: output connected to on-board and front panel power LEDs
- GPP_D18: output connected to PERST# of both CPU PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D19: output connected to PERST# of both PCH PCIe Slots. Can be
used for testing/debugging only, since it resets both slots at once.
Not actively used by vendor firmware.
- GPP_D22: input connected to the BMC enable/disable jumper JPB1; Will
be used later in CB:48096 and CB:48097; external pull-up
- GPP_G0 - GPP_G3: dedicated/integrated CPU switching; probably not
useful, since the IGD is not connected to any ports on this board.
External pulls ensure correct function of a dGPU even without driving
the gpios. Not used by vendor firmware.
- GPP_G12 - GPP_G16: inputs for binary SKU_ID; external pulls
- GPP_G20: PWRFAIL# input from JPI2C1 (pin 3); external pull-up; Not
used by vendor firmware.
Also add comments for documentation. While at it, mark ME-owned pads as
reserved.
Change-Id: I9f9328e9ce6f7e291b171f776bb98bc617b64b93
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
This change reorganizes FMAP for volteer to make use of the lower
16MiB of the SPI flash for RW_SECTION_A and RW_MISC in addition to
RW_LEGACY. This is now possible because TGL supports memory mapping of
BIOS region greater than 16MiB.
Following changes are made in chromeos.fmd as part of this:
1. Move RW_SECTION_A and RW_MISC to lower 16MiB.
2. Reduce size of RW_LEGACY to 2MiB since we longer need to use it as
a placeholder in the lower half of the SPI flash.
3. Reduce size of RW_ELOG to 4KiB as coreboot does not support a
larger region for ELOG.
4. Increase WP_RO to 8MiB to allow larger space for firmware
screens. GBB size is thus increased to 448KiB.
BUG=b:171534504
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I0c3c0af94183a80c23d196422d3c8cf960b9d9f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
AP_PEN_DET_ODL isolated by a diode and need to pull up internally.
BUG=b:160752604
BRANCH=dedede
TEST=Build and confirm waveform by google EE parter.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I85f3d0209094af07891a5c0cc218443da586e6e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48294
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the PMC MUX and CONx devices for adlrvp for
conn2.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I52afbd429750cfa416f4ed93aeb1be590f8c3a5c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48230
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change restricts RW_DIAG region to lower 16MiB to ensure that the
extended BIOS checker for FMAP does not complain about 16MiB boundary
crossing.
I haven't updated any other regions to occupy the newly freed space
but it is fine since this board is dead and should be dropped from
coreboot soon.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I19ab204fbe3e020e42baf68bfa350dcff32066a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change restricts SI_ME region to live below the 16MiB boundary to
ensure that no regions cross the 16MiB boundary as the extended BIOS
window checker for FMAP complains about it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib0838ff4c63b06b8dc169b40d3022965b2f2f8f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch adds the PMC MUX and CONx devices for lindar. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:172533907
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id5ee78b7ece8421144086af9b95f5f0d849be56c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
SATA_AHCI is already the default mode for CNL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I814e191243224a4b021cd7d4c1b611316f1fd1a4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Align the SATA mode names with soc/skl providing a consistent API.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I54b48462852d7fe0230dde0c272da3d12365d987
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
The PCI devices P2SB and PMC are hidden by the FSP and cannot be
unhidden, because the FSP locks their configuration. Thus, setting them
to `on` is not correct. Therefore, set their state to hidden.
Change-Id: Ib7c019cd7f389b2e487829e5550cc236ee5645b7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48388
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SATA_AHCI is already the default mode for SKL/KBL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: Ib5222c1b0314365b634f8585e8a97e0054127fe9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48378
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Angel Pons