Configuration of pins exposed by superIO are inconsistent between board
variants. Each platform should have UARTs enabled, this is expected
behaviour of these pins. Given that APU2_PINMUX_UART_x can be set for
all boards as default.
Change-Id: Ifb7dfe23a95ba0e572adc38212333d9fdd234d53
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/28720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
My CPU (3770k) supports 9 MCE banks, but the code is hardcoded to reset
only 7. This causes Linux to spuriously log errors during boot and S3
resume.
Fix this by reading the real value from the right MSR.
Change-Id: Id05645009259fd77b4de49bde518361eeae46617
Signed-off-by: Dan Elkouby <streetwalkermc@gmail.com>
Reviewed-on: https://review.coreboot.org/28443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This board doesn't support the newest RISC-V Privileged Architecture
spec (1.10), and it's based on an FPGA so it's a moving target.
Now that there's actual RISC-V silicon out there (from SiFive),
mb/lowrisc/nexys4ddr will only continue to bitrot.
Change-Id: I4e3e715106a1a94381a563dc4a56781c35883c2d
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Need to tune I2C bus 6 clock frequency under the 400KHz
Bug=b:116543001
TEST=flash coreboot to the DUT and measure I2C bus 6 clock
frequency whether arrive to 399.1KHz
Change-Id: I95b535a6b429fc34961a4953004a1c51e53a9be6
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28747
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since I2C bus 7 attached the touchscreen device however Phaser units
that haven't it. So for avoiding side effects, we need close I2C bus
7 SCL and SDA respectively.
BUG=none
TEST=according to sku_id (Phaser: 0x1, Phaser360: 0x2, Phaser360s: 0x3)
distinguish whether close these gpios.
Change-Id: I8ad17761f2a053dc329bbec0a0a3284d47289666
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28669
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jett Rink <jettrink@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since each variant has a separate build, we don't need to support
multiple manufacturers in a single file.
BUG=b:79874904
TEST=Build, boot, see updated mainboard manufacturer
Change-Id: I0ccf207ba8d5e5200aa4b19c46784bbda82f7b6e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
To disable NB-Pstate, the system wouldn't auto restart on EVT board when idling.
BUG=b:116082728
Change-Id: Iec4f0355cb6eb1c2b0372e3d131cc5e6ba36635e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The following was tested:
- CPUs with 800, 1067, 1333MHz FSB (1333MHz FSB needs a jumper set)
- The VGA output with libgfxinit
- USB
- COM1
- Ethernet
- SATA
- PCIe
- PCI
Has the following problems:
- The Ethernet NIC is not usable after S3 resume and requires Linux to reload
the driver. Vendor firmware also has this problem so it is quite likely it
is just a atl1c driver problem.
TODO: Add documentation
Change-Id: Ibce9ecdc0e44db3703401f116c9a8bff5b66437f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Eliminate the references to PspBaseLib.c and PspBaseLib.h in
agesa_headers.h. Fix psp.c references to definitions in those files
by adding them to include/amdblocks/psp.h.
BUG=b:78514564
TEST=Build and boot grunt/ChromeOS and restore an image from the internet.
Change-Id: I2740ceb945736c6e413f7d0bd0c41a19e19c7d5a
Signed-off-by: Charles Marslett <charles.marslett@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27619
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
STAPM programming was created inside function OemCustomizeInitEarly().
It should be SOC specific, and called by agesawrapper just before the
call to OemCustomizeInitEarly().
BUG=b:116196626
TEST=build and boot grunt
Change-Id: I8a2e51abda11a9d60a9057b38f2a484e1c8c9047
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28705
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add support to set eMMC tuning params from the device tree so that it
can be configured per board.
BUG=b:112718426,b:112690628
BRANCH=none
TEST=Build nocturne image and checked values passed in dev tree is set
by FSP.
Change-Id: Ic71934dce9a1c380a057e579ca3fda41983b9385
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/28274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This commit creates an ampton variant for Octopus. The initial settings
are copied from Bip, but the following changes are made to support
hardware differences:
* GPIO_66 is not connected (LTE).
* GPIO_67 is not connected (LTE).
* Updated comment for GPIO_134 (EC_AP_INT_ODL), but not configured yet.
* GPIO_143 is not connected.
* GPIO_144, GPIO_145 mapped to PEN_EJECT are not connected.
* EN_PP3300_TOUCHSCREEN moved from GPIO_213 to GPIO_146.
* GPIO_213 is not connected.
* GPIO_214 is not connected.
BUG=b:111498206
TEST=None
Change-Id: I7d6cf19c906df19115b1101e3d91c62f5f3f61e3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/28663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add new mainboard variant of whiskey lake rvp, which is primary
validation platform for whiskey lake silicon, support socket DDR4 memory
module.
BUG=N/A
TEST=Build and flash, confirm boot up into kernel on whiskey lake rvp
platform.
Change-Id: I4a5e8a9ec76d5e55e55ef9bf968825c17fbe9816
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch sets the MRC UPD "CmdTriStateDis" to disable TriState for
the rammus boards. Rammus is LPDDR3 design without RTT for CMD/CTRL.
BUG=none
TEST=Run memtester app and also webgl fishtank on the LPDDR3 kabylake
boards and also check the margin data is proper in FSP.
Change-Id: Iee115f49ba5b36dc5b0425e9da02b58cd19b2236
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28568
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's only DDR4 or LPDDR3 support for coffelake processor line,
details can be found out on EDS #570805.
BUG=N/A
TEST=N/A
Change-Id: I8ba6b6861b15b40b01237f87c8d55394f7fd6706
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
No support for SoC D-1 stepping is available.
According to Intel doc #332095-015 stepping C-0 has revision
id 0x21 and D-1 revision ID 0x35.
Also correct the RID_C_STEPPING_START value for C-0.
BUG=none
TEST=Built, Intel Cherry Hill Rev F.
Change-Id: I29268f797f68aa4e3b6203e098485e0bd4a44fc4
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27471
Reviewed-by: Wim Vervoorn
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix warning from list in table cells for nri_registers.md
Change-Id: I2b77ad266d1c5f693536e161f96f3db19832989c
Signed-off-by: Tom Hiller <thrilleratplay@gmail.com>
Reviewed-on: https://review.coreboot.org/28354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t is deprecated.
Change-Id: I70dcefd5bc9864931f66bece1f044f806f5d7ae0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This included the microcode for some CPUID's found in
soc/intel/skylake/bootblock/report_platform.c (others are likely pre-release
SKU's)
The amount of FIT entries needed is currently 7 so setting
CPU_INTEL_NUM_FIT_ENTRIES is set to a safe 10 will be able to fit them all.
Change-Id: I3ba504a07b2697fe55ff8f28a934f761ae05a4ec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set up EC_IN_RW GPIO to boot depthcharge. Without this patch,
depthcharge will fail to tell if the EC firmware is RW.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui and see in logs, that depthcharge detects
EC_IN_RW GPIO.
Change-Id: Icb39d663f65b72e0ad54059c9590d9693106ee25
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28670
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change GPP_D17 and GPP_D18 to no connects as DMIC was moved
to DMIC0.
BUG=b:113744731,b:111106010
TEST=none
Change-Id: I8ef42627e542182707c81389af9da33a114bc184
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28689
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Grunt variants need a way to customize the mainboard vendor based on the
platform. For future boards, this can probably be done via CBI, but
grunt doesn't support that method.
BUG=b:79874904
TEST=Build, boot, see updated mainboard vendor
Change-Id: I997dc39c7f36f70cf4320ef335831245889eb475
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/28651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
Update Power Limit1 and Power Limit2 values along with stepsize.
Correct the charger effect for Temperature sensor2.
BUG=b:112448519
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I01e0a94fe694537d9eebe3b92c11d0c83137d716
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28530
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to cannon lake PCH BIOS specification document #570374
target port id for interrupt and timer subsystem(ITSS) is C4 instead of C2.
BUG=None
TEST=None
Change-Id: I9f8783c682d2c4c4a86e1c9cf4b9c27a18fdf494
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Kin Wai Ng <nelsonaquik@gmail.com>
A negative side-effect is that those boards disappear from the board-status
output, but this is an issue on all variants.
Change-Id: Ic80804dc1f7d9c6f83ceee3db667019532c31d4c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove const define for spd_smbus_address, the value can be updated
depends on platform configuration.
TEST=Build and Run on Whiskey Lake rvp platform.
Found-by: Converity Scan #1395725
Change-Id: Ib933ed872e9f85087bb3cd76a1f1e29cca75cd54
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28664
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When preparing transition of AGESA calls to romstage, I placed a comment
indicating the place to move a particular call. Now that the AGESA call
has been moved to romstage, the comment became obsolete.
BUG=b:116095766
TEST=none.
Change-Id: I2811657385ab088747e32d4c66b99fdd01e7315e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
It is much more convenient to view these files if there are 8 values per line,
not 1 value which results in a very long file. The contents remain the same:
these microcodes are still the latest publicly available at the time of writing.
Change-Id: I3e5296a5b5e895702a60aca1ded7418bb345263d
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-on: https://review.coreboot.org/28391
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This microcode update for CPU ID 0x300F10 should improve the system stability.
It is a part of microcode_amd.bin officially released by AMD at linux-firmware:
it starts at 0x217C offset, and size is 0x03C0 as specified priorly at 0x2178.
Old version: 0x300000F [2010-04-10]
replaced by
New version: 0x3000027 [2011-09-13]
Change-Id: I9650fab377d957904318ebb393323c2509cfea26
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-on: https://review.coreboot.org/28378
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The helper function to get the board version from EC returns 0 on
failure. But 0 is also a valid board version. Update the helper function
to return -1 on failure and update the use-cases.
BUG=b:114001972,b:114677884,b:114677887
Change-Id: I93e8dbce2ff26e76504b132055985f53cbf07d31
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Tested-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/28576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 1 for EVT.
BUG=b:115965629
TEST=verified it in meep proto board which rework ram id.
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I962b099d5b9fbe0ca29708be1e9c6ed60b10d363
Reviewed-on: https://review.coreboot.org/28658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
FSP initializes the VT-d feature on Broadwell-DE and assigns an address
space to the MMIO range. coreboot's resource allocator needs to be aware
of this fixed resource as otherwise the address can be assigned to a
different PCI device. In this case addresses are overlapped and the VT-d
range is not accessible any more.
To deal with it the right way add a fixed MMIO resource to the resources
list if VT-d BAR is enabled.
TEST=Booted into Linux and checked coreboot log for resource assignment.
Change-Id: I626ac17420eadc0b49031e850f0f40b3b221a098
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/28672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Michał Żygowski