Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Based on the Intel G41 chipset, ICH7 southbridge, and IT8720F Super I/O.
Tested, working:
* Booting Linux 4.11.3 and Windows 8.1 from USB and HDD
* Resume from S3 (Linux and Windows)
* Native raminit (DDR2-800)
* Native graphics init (SeaBIOS, Linux)
* Graphics init with VGA BIOS (SeaBIOS, Windows)
* PCI-E x16 PEG slot, PCI-E x1 slot from southbridge
* Realtek ALC888 HD Audio (including front panel and jack detection)
* Realtek R8168 Gigabit LAN
* Both SATA ports
* USB 1.1 and 2.0 devices (keyboard, mass storage)
* PC speaker beep
* COM header
* Super I/O Environment controller (temps, voltage, fans)
* PS/2 keyboard and mouse
* Flashing with `flashrom -p internal`
* 1MiB and 2MiB SPI flash chips
* CMOS gfx_uma_size
Appears, OS driver loads, but otherwise untested:
* IrDA header
* CIR header
* TPM header
Untested:
* S/PDIF digital audio
Tested, known broken:
* CMOS power_on_after_fail
* USB keyboard in secondary payloads
Change-Id: Ifc4c8935b1a11e55f4bf6cfa484a8a8d09b1adda
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20027
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
I updated my spike patch[1] to cleanly apply to current spike master.
As a side effect, the UART is now at 0x02100000.
[1]: https://github.com/riscv/riscv-isa-sim/pull/53
Change-Id: I4cb09014619e230011486fa57636abe183baa4be
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/20126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for google/rambi
as to not break compilation.
Change-Id: I4ef978214aa36078dc04ee1c73b3e2b4bb22f692
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20056
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Update devicetree PCI config based on board spec:
- enable PCIe Root Ports 5 and 9 (wifi and nvme respectively)
- enable PCIe CLKREQ on RP9, disable on RP5
- enable USB OTG
- enable P2SB
Note: PCIe RP5 is on 0.1c.0 despite this being labeled as RP1
Change-Id: Ia71ed25bd41668df1ee3e4b4e28f54482722452c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The FSP Temp RAM init will fail if the mircocode values are set
to 0. A valid microcode update needs to be included and its size
and offset need to be set in the config.
Change-Id: I26d05bd7b37c8d91bf34f399c7c4189f9d3dd34a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19936
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Adding code to setup the spd information from sodimm.
Adapted from intel/kblrvp.
Change-Id: I0403f999dac1bdef0e9e1abe7c9c62407e223bb1
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The GPIO configuration matches the one from the original BIOS.
Some configs don't make much sense, but I kept it as is so it
would match (such as a NC pin with TX set to 1, or RXINV enabled).
Remove unnecessary early GPIO config.
Change-Id: Iaec8630cef9a523fb2e2503143aa4aa72fbedc1f
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19934
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Like other devices using ENE embedded controllers, the librem13v2
requires this config option for the PS2 keyboard and mouse
(trackpad) to function properly.
Change-Id: Ifba13b93a1fe2e76b2790d1c273fd9e2b5368ab0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add the initial directory for the port of the Librem 13 v2.
The base implementation was copied from the google/chell directory
and the chell references were replaced. spd directory was removed
since the RAM is not soldered on the MB. The Kconfig, board_info.txt
and devicetree.cb files were modified to match the Librem 13 v2
hardware information. The romstage.c, mainboard.c, Makefile.in and
dsdt.asl were modified to remove chromeos specific code. The boardid.c,
chromeos.c, chromeos.fmd, cmos.layout, ec.c, ec.h and smihandler.c
files were removed from the tree, and the acpi directory was replaced
with the acpi directory from the purism/librem13 board.
These changes allow us to remove the references to chromeos specific
code and allow coreboot to compile when the librem13v2 board is selected.
Change-Id: I24263fde18fcea70163dbdc59df6ea1d98c97af8
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The FADT revision was set to 5, but we do not implement the
ACPI v5.0 specification, which prevents Windows from booting.
Setting it to v3 (matching most other boards) fixes the issue
and Windows now boots normally.
Bug found by Matt DeVillier, fix tested by Youness Alaoui on
Librem 13 v1 hardware.
Please also see commits 00d250e228 (intel/skylake: Switch FADT
to ACPI version 3.0) [1] and 27e6042bb7 (intel/apollolake:
Switch FADT to ACPI version 3.0) [2].
[1] https://review.coreboot.org/19453
[2] https://review.coreboot.org/19146
Change-Id: Ide97cbf64f7b05018433436431ab4723b217fe22
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
A simple rename of the directory and the config values
and string in Kconfig/Kconfig.name/board_info.txt
It will be less confusing for users since the first models
are referred to as 'v1' everywhere now.
Change-Id: I23fa977717230c2001868741bb684e9633a2c0bb
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19931
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for intel/strago
and google/cyan as to not break compilation.
Change-Id: Iaf8211bd86d6261ee8c4d9c4262338f7fe19ef43
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Change-Id: Ie0b64eadc634049f6b65cf555407337fb7c4363c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Switch from lapic to tsc.
Allows timestamps to be used in coreboot, as there's a reference
clock available to calculate correct time units.
Clean Kconfig, remove duplicated lapic code and include tsc dir for
LGA1155 boards.
Tested on Lenovo T430.
Change-Id: I849ca2b3908116d9d22907039cd6e4464444b1d1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update user facing camera i2c address to 0x36.
BUG=None
TEST=Build & boot on soraka. Make sure user facing camera is detected.
Change-Id: I4645ae5734faef4b6a821c04ab817a7b99da6e4b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
The new config choice is called RUN_FSP_GOP. Some things had to happen
on the road:
* Drop confusing config GOP_SUPPORT,
* Add HAVE_FSP_GOP to chipsets that support it,
* Make running the GOP an option for FSP2.0 by returning 0
in random VBT getters.
Change-Id: I92f88424004a4c0abf1f39cc02e2a146bddbcedf
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide all gfx init methods as a Kconfig `choice`. This elimates the
option to select native gfx init along with running a Video BIOS. It's
been only theoretically useful in one corner case: Hybrid graphics
where only one controller is supported by native gfx init. Though I
suppose in that case it's fair to assume that one would use SeaBIOS to
run the VBIOS.
For the case that we want the payload to initialize graphics or no
pre-boot graphics at all, the new symbol NO_GFX_INIT was added to the
choice. If multiple options are available, the default is chosen as
follows:
* NO_GFX_INIT, if we add a Video BIOS and the payload is SeaBIOS,
* VGA_ROM_RUN, if we add a Video BIOS and the payload is not SeaBIOS,
* NATIVE_VGA_INIT, if we don't add a Video BIOS.
As a side effect, libgfxinit is now an independent choice.
Change-Id: I06bc65ecf3724f299f59888a97219fdbd3d2d08b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MAINBOARD_FORCE_NATIVE_VGA_INIT is to be selected instead of the user
option MAINBOARD_DO_NATIVE_VGA_INIT. The distinction is necessary to
use the latter in a choice.
Change-Id: I689aa5cadea9e1091180fd38b1dc093c6938d69c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The word 'coreboot' should always be written in lowercase, even at the
start of a sentence.
Change-Id: I7945ddb988262e7483da4e623cedf972380e65a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The coreboot sites support HTTPS, and requests over HTTP with SSL are
also redirected. So use the more secure URLs, which also saves a
request most of the times, as nothing needs to be redirected.
Run the command below to replace all occurences.
```
$ git grep -l -E 'http://(www.|review.|)coreboot.org'
| xargs sed -i 's,http://\(.*\)coreboot.org,https://\1coreboot.org,g'
```
Change-Id: If53f8b66f1ac72fb1a38fa392b26eade9963c369
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Wrapping the long line tries to address a warning by `checkpatch.pl`,
but the line is still over 80 characters long.
Change-Id: Ib75d4da1880624eb83f7a419cb6762f1c4c2a7b2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/20033
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The comma-separated PCI vendor and device ID is used to associate the
VGA BIOS to the video device by using it as the file name of the VGA
Option ROM.
Change-Id: I755554eeb9a560d034d6e8fe49de619d800ea045
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes the offsets of some options so that options that span multiple
bytes are byte aligned.
To make the cmos.layout file more consistent some things where moved
around in the cmos.layout of thinkpads X200 and T400.
Change-Id: Ic84a2a5dc6f9c102f041085871c2ed55e2f3692a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
A new variant copied from reef.
Allow override of the SKU.
Change-Id: Ibe160e75aa23623812f0fb9121d1d8226afc00d8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20020
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each rambi variant has a different USB port config.
Port data currently available for only candy and squawks;
other variants to be added once data obtained.
Change-Id: If7ce3d135d6ffe53ab1566d5258d01b052ac47f4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each jecht variant has a different USB port config.
Change-Id: I3b15aac9c4971e2ae230106016fba3a583ec6c9a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each auron variant has a different USB port config.
Change-Id: Id17f21c23540d2e3d5a902a2174b66c7a5a5f3e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Since dual-channel setups use same RAM/SPD for both channels,
populate spd_data[1] with same SPD data as spd_data[0],
allowing info for both channels to propogate into the
SBMIOS tables.
Clean up calculations using SPD length to avoid repetition.
Changes modeled after google/auron variants.
Change-Id: I7e14b35642a3fbaecaeb7d1d33b5a7c1405bac45
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
No reason to compile/include chromeos.c for non-ChromeOS builds
Change-Id: Ie8ef1f4c521b2a7308941299f2501073937bdf4a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
sata_devslp_disable was set to work around some buggy SSD
firmware, but as it's disabled by default in both Linux and
Windows, no reason to disable at the firmware level when
many properly-functioning SSDs can take advantage of power
savings.
Change-Id: Ib15f8b51db19b3d9d2e135f85c71a15a45a2ffbd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Update camera sensor detail to OV 13858
Also update i2c address of OV5670
BUG=None
TEST= Build & boot to ChromeOS. Check for both the camera detection.
Change-Id: I3b6192815201f605d3ebdb4bf54db26a8e837b35
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fix for all Sandy-Bridge and Ivy-Bridge devices.
Remove unused option "hyper_threading".
Increase CMOS checksum range to cover all user adjustable settings.
Change-Id: I02f7af13d9c82d7f531d4b49b3bc0e5a20c14b55
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is to align with the SD_CD GpioInt setting in acpi
BUG=b:62067569
TEST=checked unused interrupt on SD_CD does not happen after s3 resume
Change-Id: I40aefcb0f571e7f6773a6d20226f357707aa041a
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/20001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Like HAVE_VGA_TEXT_FRAMEBUFFER, these are selected by graphics drivers
that support a linear framebuffer. Some related settings moved to the
drivers (i.e. for rockchip/rk3288 and nvidia/tegra124) since they are
hardcoded.
Change-Id: Iff6dac5a5f61af49456bc6312e7a376def02ab00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
* Rename it to HAVE_VGA_TEXT_FRAMEBUFFER.
* Let drivers select it if they are in charge.
* Don't select it on the mainboard level if a driver handles it.
Change-Id: I2d9d09be9aa6d019e77460e69a245ad2d8cda4ea
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The separate directory was the old way of handling variant boards.
Update bakersport_fsp to the new method. All of the other pieces
were already moved into bayleybay_fsp.
Change-Id: I5712c1b399570bd7ab7fc9e42af25fbf15a0ba78
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/19077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Light sensor isn't used and ACPI already removed, so disable
I2C5 bus interface as well.
Disable I2C6 for devices without a touchscreen
Change-Id: Ib0e041ae9131615ef1140bad064de5aae91f8ee4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Remove MONOTONIC_TIMER_MSR selection from mainboard
Konfigs, as it only does a reduntant selection of
HAVE_MONOTONIC_TIMER config, already selected under
skylake soc Kconfig.
Change-Id: Ib3177ceb9e8b6c16ce0e437a4a02b94f215af58f
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/20002
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
This board is almost identical to D510MO, the only differences are
some differences in populated connections, CPU with less L2 cache and
a 10/100 Realtek NIC.
The vendor uses the very same binary for both D510M0 and D410PT.
Change-Id: I220515365b69e785ef249c4e3a9af5f7fddf02f9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
Each slippy variant has slightly different USB port config;
data for falco and leon to be added once available
Change-Id: Icc3b5b1161f62ac0b840380679acafeff363cf45
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Add capability and location data for USB ports/devices via
_PLD and _UPC ACPI methods, which is utilized by Windows and
required by macOS.
All beltino variants use the exact same USB port layout.
Change-Id: If5b540949ea071f7165876e12ac1ef50e62d2b22
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
.jpg){kind=link}
.jpg){kind=link}