Add CPU PortID for GPIO communities in order to calculate
IOM Aux Bias data correctly.
BUG=b:283044004
TEST=able to detect external display
Signed-off-by: Marx Wang <marx.wang@intel.com>
Change-Id: I79f27fb0b6bde0a4ce2466eaf707166a952fad81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Add devicetree and Kconfig entries to enable additional configuration
of the Pericom PI7C9X2G608GP PCIe switch on this board variant.
The amplitude is being adjusted to 425 mV and de-emphasis level to
6.0 mV.
BUG=none
TEST=Read out the PCIe config space values of the switch and check if
they match with the ones configured over SMBus.
Change-Id: I11459f0794278ad614aa6e16c56df1ad578fe2f8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
To improve the rate of data transfer for PCIe root port #2 (00:1c.1) and
root port #3 (00:1c.2) set the max payload size to 256 bytes for both
root ports.
Change-Id: I553f6cf090d799fbbaafb925646c6566d6951a86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75127
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
The data payload size of PCIe root ports can be set to either 128
(default) or 256 bytes. A bigger payload size can improve PCIe data
throughput on the given port. FSP-S provides a parameter to configure
this value.
This patch provides a chip config so that this FSP parameter can be set
as needed in the devicetree on mainboard level.
Change-Id: I5798a72adaa8089dda0b4bc12266b5a235ed4aa3
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Override the weak function mainboard_ewl_check() and select OCP_EWL.
Select IPMI_KCS_ROMSTAGE and IPMI_OCP for OCP IPMI commands which are
needed for OCP EWL driver, but they are Meta-specific BMC commands
and don't really work for AC, this change is just for a demonstration
with AC.
Note that FSP UPD promoteWarnings needs to be disabled so that
FSP won't block and can return to coreboot for EWL processing
when memory EWL type 3 error occurs.
Tested=On Intel AC, connected with a faulty DIMM can see
EWL type 3 error being generated and halted with coreboot log:
[DEBUG] Number of EWL entries 3
[ERROR] EWL type: 3 size:32 severity level:1
[ERROR] Major Warning Code = 0x29, Minor Warning Code = 0x04,
[ERROR] Major Checkpoint: 0xb7
[ERROR] Minor Checkpoint: 0x74
[ERROR] Socket 0
[ERROR] Channel 4
[ERROR] Dimm 0
[ERROR] Rank 0
[ERROR] IPMI: ipmi_get_board_config command failed (ret=3 resp=0xc1)
[DEBUG] ipmi send memory training error
[DEBUG] EWL type: 1 size:19 severity level:1
[DEBUG] 0x6392e968: 01 00 00 00 13 00 01 00 00 00 b7 74 0a 03 00 04
[DEBUG] 0x6392e978: 00 00 00
[DEBUG] EWL type: 1 size:19 severity level:1
[DEBUG] 0x6392e97b: 01 00 00 00 13 00 01 00 00 00 b7 74 0a 03 00 04
[DEBUG] 0x6392e98b: 00 00 01
[EMERG] Memory Training Error!
Change-Id: I4602ae356aa6e55ed0611b8ac9a206db127c297c
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
If Fastboot is enabled, the next boot will skip MRC and won't be able
to detect MRC error via EWL and still continues booting. Enforce FSP
MRC training in the next boot.
Change-Id: I9dee0472f8e2602cecf88c6d00dec0bf02b9f7bd
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
1. Rename set_cmos_mrc_cold_boot_flag() to soc_set_mrc_cold_boot_flag
in case a certain platform may not support this via CMOS data, and
the function could in turn calls mainboard defined method in the
future. Move the code into soc_util.c.
2. Remove redundant static get_system_memory_map() from cpx/romstage.c
and call the soc_util.c one.
Change-Id: Ib7d9bed9092814658f4a0b1d6dcf3c7d79178048
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ic498afcc8b8e0224f344f405e2f1ef6184df1d6b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75340
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
The comment got stale because a few elements from the struct got
dropped.
Change-Id: I83469e24dfab82b9182accb549960dd06d81e02f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
%ebp is used for the stack frame on which the fxrstor address is pushed.
entry64.inc does not trash it so that's fine.
Change-Id: If027437dccac9ad507ceb534c6aae77ea43bdfda
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68896
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ie40541ada508acfa5771ea800249b8a57b168e3b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75339
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, verify error no longer present in dmesg.
Change-Id: I0b87af6b2c04f9354e6f394a8f987fa660e49134
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75338
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I05a2cd5f2235702dea8fd706349ebda6a9ffa2ef
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
This change updates Intel Copyright License for all header files
under Sapphirerapids dir
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ib04988194e5fe9515bea8620318eadff36f92181
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Add `ramtop` to CMOS layout so SOC_INTEL_COMMON_BASECODE_RAMTOP
can be used.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I88128d2c62bdc3246a3f30e768c353f0fe3faeb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
This is needed to support 9-series PCH-H (e.g. Z97) and Broadwell
non-ULT CPUs (for which more magic is required).
Tested on Asrock Z97 Extreme6: Boots, but ME has to be disabled so that
the system remains on after 30 seconds. Apparently, something Broadwell
MRC.bin does results in the ME being unhappy, as there is no such issue
when not using MRC.bin at all (native RAM init). S3 resume is working.
Change-Id: I7b33660099fa75c5ad46aeeda17b1215729f96c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
BUG=b:282912666
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Iee6a9026a4d210407350bfb7ecc8a058e7ff5c24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
According to Thermal table 0518, adjust DPTC and STT settings.
BRANCH=none
BUG=b:273636128
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Id1c1884eabc1ea58148270f39eaca836ccc3fb54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Remove duplicated definitions of ARRAY_SIZE macro across util/ dir.
Instead of duplicates, use the one from commonlib/bsd/helpers.h file.
BUG=b:231765496
TEST=make -C util/cbfstool; make -C util/cbmem;
make -C util/intelmetool; make -C util/superiotool
Change-Id: I29b776586b4f0548d4026b2ac77095791fc9f3a3
Signed-off-by: Konrad Adamczyk <konrada@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74474
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Grzegorz Bernacki
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The board needs this setting to boot.
Change-Id: I7f507c2478b63daf891430e95b008747b9b95a51
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Earlier the entire SPI ROM is mapped at the start of verstage and then
unmapped at the end of verstage. With CB:74606, this behavior has
changed. So unmap the hash table CBFS file after usage.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim. Perform cold, warm reboots and
suspend/resume cycles for 50 iterations each. Ensured that there is no
impact to boot time.
Change-Id: I5c605f8ba8bbd571b589b3cdf91e9cc71d711c1c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75092
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently the SPI ROM is mapped completely when the boot device is
initialized. That mapping remains active throughout the execution time
of PSP verstage. Every 1 MiB of mapped SPI ROM region consumes 1 TLB
Slot in PSP for use during memory mapped or DMA access. With 16 MiB of
mapped SPI ROM + FCH devices + 4 reserved TLB slots, 31 out of 32 total
TLB slots is consumed. This leaves almost no scope for future expansion.
With upcoming programs possibly using 32 MiB SPI ROM, PSP will run out
of TLB slots to support 32 MiB.
Hence instead of mapping the entire SPI ROM upfront, get the SPI ROM SMN
address during the boot device initialization. Update the boot device
region operations to map and unmap the SPI flash with the desired offset
and size using the SVC call. Then anytime a memory mapped SPI ROM access
is performed: map the required area, read the data and immediately unmap
the area. There is no update required when using CCP DMA, since the
concerned SVC call performs mapping and unmapping of the required SPI
flash area implicitly.
With these changes, maximum of 8 slots(size of RO section) might get
used at any point in time during the PSP verstage execution.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim. Perform cold, warm reboots and
suspend/resume cycles for 50 iterations each. Ensured that there is no
impact to boot time.
Change-Id: Icd44ea7b2a366e9269debcab4186d1fc71651db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74606
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add sending Meta's BMC SEL for memory training error occurred in EWL
type 3 error.
The detail definition of EWL (Enhanced Warning Log) can be found in the
specification document -- BIOS Data ACPI Table (BDAT) Interface
Specification v4.0 Draft 5:
https://uefi.org/sites/default/files/resources/BDAT%20Specification%20v4.0%20Draft5_0.pdf
Change-Id: I664e9d3da7910b47260881c0df64159c8dbe2dca
Signed-off-by: Shelly Chang <Shelly_Chang@wiwynn.com>
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69147
Reviewed-by: Jonathan Zhang <jon.zhixiong.zhang@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently unsigned PSP verstage binary is copied from ELF file only when
required in amdfw*.rom. If a signed PSP verstage binary is supplied
while building amdfw*.rom, then it is dropped. Copy the unsigned PSP
verstage binary always so that it can be used for signing directly from
the CI build infrastructure instead of a locally built binary.
BUG=None
TEST=Build Skyrim BIOS image and ensure that the unsigned PSP verstage
is part of the build artifacts.
Change-Id: If797dcfd20aa2991f3517904ef862406b9b9875c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75334
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Pujjoteen5 support WWAN 5G device, use variant.c to handle the
power on sequence.
BUG=b:279835626
TEST=Build and check WWAN 5G power on sequence.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I7dc72f2c705bcb41745f4bf08bef286773fe8b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75327
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the DmaProperty in the device's _DSD so that the OS can treat the
device as untrusted.
BUG=b:278310256
TEST=cat /sys/bus/pci/devices/<wifi>/untrusted == 1
iperf3 -c <iperf3-server> -t 60 (No performance regressions seen)
Change-Id: I06369a19afa5b881b26f5c1eb243e2db41a9bb36
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75095
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Show an error if an option table is used, and the ramtop entry is not
defined on a platform that uses it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie48f0766b29be8e1fb0c1f71c4b2ce6ed20e6207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
CB:37152 was supposed to be uprev to Linux's kconfig, but it got this
one case wrong, Linux never returned "0" [1]. As a result, when an
option has default value different than 0, and it was changed to 0,
savedefconfig skips saving it. However, during the build from such
defconfig the option is assigned default value.
TEST=Set SEABIOS_DEBUG_LEVEL to 0 and see that savedefconfig writes
it to defconfig file.
[1] 7cf3d73b43
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I821e45dcec99904fab85f136298cbd0315237ff6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72650
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
During the cleanup of copyright lines, this file was incorrectly changed
to remove the copyright line. It is not originally a part of the
coreboot project, having been pulled in and adapted for use in coreboot.
As such, and with the ISC license specifying that the copyright line
should be maintained, the copyright line has been restored.
See coreboot ticket # 479 for more information.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ia234cebd0a6d49d03e40c5a57cd346a07f3e4b09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Set all GPIOs to their target functions and do not depend on FSP to
configure them. The board support has stabilized and was tested with
many PCIe devices. There is no need to detect CLKREQ signals so we may
hardcode them.
TEST=Boot MSI PRO Z690-A DDR4 to Linux and check if all ASPM and Clock
PM features' state on PCIe root ports are the same before and after
the change.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I01dc83ce23ca27525b8905665da942510f249824
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Disable backlight before turning on bridge, otherwise the bridge will
initialize failed.
Fixes: d5c1e1(mb/google/corsola: Add support for MIPI panel)
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7d10bf9e8675b2fb03bfd1e294af66207b9b0620
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75354
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
The upstream kernel privacy screen driver uses HID GOOG0010 to look for
firmware node to use. This method is used on other boards, e.g. redrix.
See: drivers/platform/chrome/chromeos_privacy_screen.c in linux sources.
Update jinlon gfx ACPI node to work with that.
BUG=b:279092050
TEST=privacy protection screen works with 5.15 and 4.19 kernels
Change-Id: Icba41e7f2be7292f713fea10dbe69b3ca128bde7
Signed-off-by: Kornel Dulęba <korneld@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75289
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
The support for the board has stabilized and PCIe ports have been
tested with many devices. Although hotplug is not commonly used
and it seems pointless to keep it enabled, so disable it.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I338c55cb57d971badd08235b71626a710fafb829
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
The Bochs graphics adapter remaps the legacy VGA ioports
(0x3c0 -> 0x3df) to its MMIO region at offsets 0400 - 041f.
Currently bochs_vga_write() calculates a wrong offset when
accessing these ioports, which causes the boot splash image
not displayed when using the legacy-free pci variant of the
Bochs graphics adapter.
TEST=Build coreboot for QEMU x86 i440fx with a boot splash image
included, boot coreboot.rom with QEMU with '-device secondary-vga'
and verify the boot splash image is correctly displayed.
Fixes: efaf1b32ba ("drivers/emulation/qemu/bochs: Rewrite driver")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Change-Id: I4acc71e3d6ef5161ab62e6714c94b7643c4c0972
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75146
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
The named choice isn't needed here, so get rid of it. This fixes the
build notice:
build/auto.conf:notice: override:reassigning to symbol LAPIC_ACCESS_MODE
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I70628007319a0ee2830dc4c9cb3b635d8190264b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75133
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Select INTEL_GMA_HAVE_VBT so VBT files are added by default. This board
has two specific VBT files that are hard-coded in the Makefile. Hence
set an empty INTEL_GMA_VBT_FILE string.
Change-Id: I0508c8016da06b401d6fbefd6e5cec1af018a5c8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
There is only a single place where we need the LVDS EDID string. Let's
call gm45_get_lvds_edid_str() right there. This simplifies the API and
helps to follow the execution flow.
The function is moved to avoid a forward declaration.
Change-Id: I86f3a88e6b661bcf60319edbe301e70304924727
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
This is how res2mmio() is supposed to be used and there was no other
use of the `mmio` variable left anyway.
Change-Id: Ifa4645bcc9ae971966587d9b67662b9dc8bae3d0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
The PCI resource should only be probed as part of the device
.init process. We can simply do that first and know that we
can use the global `gtt_res` from then on.
This simplifies the signature of gm45_get_lvds_edid_str(), and
makes changes to the API user (lenovo/x200) necessary.
Change-Id: I6c96f715abfa56dcb1cd89fde0fbaef3f1cb63ae
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
This patch adds an API to check FSP reset pending requests. This
information is useful to understand if FSP would like boot firmware to
issue any reset to complete the silicon initialization.
As per recent debug it has been found that, FSP is accumulating all
platform resets and executing a single reset from FSP Notify Phase.
As coreboot skipped calling into the FSP Notify APIs hence, it might
have missed the scope to issue the platform reset.
BUG=b:282266168
TEST=Able to build and boot google/rex and able to detect FSP reset
pending request.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibf7c996f09affa099c9124773fe2d581f370d1a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Marx Wang