- Add ME device ID for Lynxpoint LP
- Add GPU device IDs for ULT
- SATA init tweaks from checking against DXE reference code
- Remove the ICH7 from the SPI driver so it works on all lynxpoint
without having to add more LPC device ID checks
- Add function disable for audio dsp and xhci, remove PCI bridge
- Add interrupt route registers for new devices (needs romstage setup)
Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2680
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The current code is attempting to convert from an invalid
starting temperature. Since we aren't sure where the temperature
will come from yet just return a static value.
This stops the kernel from going to S5 on boot because it
thinks the temperature is too high.
Change-Id: I433fa407e545458344af5842b353df5bc71bfdad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2679
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This option is not required for haswell. Enabling the option doesn't
do anything aside from complicate mtrr calculation. Therefore, remove
it.
Change-Id: I897523ff7d3606eb89961674c2eb3d384e584857
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2678
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit adds support for the deveveloper, recovery,
and write protect querying. It just uses jumpers on the
Basking Ridge board.
Noted ability to togggle jumpers results in toggling the
respective modes.
Change-Id: Iac189a1fa0245654591e2e9075380db422a329a0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2676
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
While looking at the Basking Ridge schematic I noticed some changes
and wanted to make sure they were reflected in the GPIO map.
Change-Id: I686653c164314ae9f68c42331d2f950751411d4a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2675
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The baskingridge has a non-zero alt_gp_smi_en value in the
devicetree.cb file. It has just to be determined which GPI
pins should trigger an SMI on basking ridge. Without this change
the board would hang during boot (presumably through a SMI flood).
No more hangs once the value is zero.
Change-Id: I9704071bb7966bd3d0bbbc4aafede3f42d829b17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2673
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Grays Reef CRB is deprecated by order of Intel. Basking Ridge
is the new hotness. Therefore, rename graysreef to basking ridge.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I203497e165d8efc99d3438c4c548140a6e9cc649
Reviewed-on: http://review.coreboot.org/2672
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
- Add device IDs for lynxpoint mobile and LP variants.
- Update the clock gating setup based on BWG
- Update the SATA programming based on BWG
- Add a DEVSLP0 mux config register
Change-Id: Icf4d7bab7f3df7adef5eb7c5e310a6995227a0e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2649
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The low power variant of the chipset introduces a completely
new interface to the GPIOs.
This is a 1KB region and so needs to be moved as well so it does
not conflict with other IO regions.
Also expose the gpio_get functions to ramstage and move the
prototypes to pch.h so they can be used for both GPIO interfaces.
Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2648
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This adds microcode ffff000a and the CPUIDs for ULT.
Change-Id: I341c1148a355d8373b31032b9f209232bd03230a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2647
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Device IDs for northbridge and GPU.
Also mask off the lock bit in the memory map registers.
Change-Id: I9a4955d4541b938285712e82dd0b1696fa272b63
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2646
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
There are enough subtle differences that it is useful to have
a Kconfig entry to differentiate the ULT/LP chipet from the
desktop/mobile versions.
Change-Id: I04ca1bc6f90bcf9e6994ea7125c98347e8def898
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2645
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This commit contains a bevy of updates:
- PCI device id is updated to match Lynx Point EDS in the ME driver.
- Allocate the memory to store the consumption of the MBP.
- me_bios_payload structure is now a structure of pointers that point
into the allocated memory.
- The ICC profile structure was updated to correctly reflect the
documentation.
Verfied that output of MBP reading can handle unknown items.
Change-Id: I43cc45e6b797444c105e7c842eb5684e9c104687
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2641
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
According to the 0.8.0 ME BWG this is a new state. It's not very clear
what exactly it entails, but the Basking Ridge CRB was tripping it when
MRC_DEBUG was enabled (presumably because of a DID timeout).
Instead of 0x17 one can now see the proper message for this state.
Change-Id: I5bda1de7d3d957d38a4760a02dcd170ec48782e9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2640
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CS5536 companion device has three different power domains.
* working domain
* standby domain
* RTC domain
When the system is "off" only the standby domain is powered.
MFGPT[7:6] are member of the standby power domain.
MFGPT7 is used to control the backlight of the device and so the
timer gets used and configured during system boot. If the system
does a reboot the timer stays configured and the Linux driver
can not use it:
"ot200-backlight: ot200-backlight.0: MFGPT 7 not availale"
The cs5535-mfgpt has a function to hard-reset all MFGPTs but the
system hangs after the first access to a MFGPT register - cause
unknown.
/*
* This is a sledgehammer that resets all MFGPT timers. This is required by
* some broken BIOSes which leave the system in an unstable state
* (TinyBIOS 0.98, for example; fixed in 0.99). It's uncertain as to
* whether or not this secret MSR can be used to release individual timers.
* Jordan tells me that he and Mitch once played w/ it, but it's unclear
* what the results of that were (and they experienced some instability).
*/
static void reset_all_timers(void)
{
uint32_t val, dummy;
/* The following undocumented bit resets the MFGPT timers */
val = 0xFF; dummy = 0;
wrmsr(MSR_MFGPT_SETUP, val, dummy);
}
After playing around with this undocumented MSR it looks like I only
need to set bit 7 to free the MFGPT7.
BTW, all MFGPT[0:5] will be reset during pll_reset().
Change-Id: I54a8d479ce495b0fc2f54db766a8d793bbb5d704
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/2527
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This is no longer tied to a GPIO but has a proper chipset pin.
Change-Id: Iba70338e8c67e3c3c1cb32e69bfea1282fda8cb5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2643
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I8406cec16c1ee1bc205b657a0c90beb2252df061
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2618
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The register that controls global reset is named the Power
Mangement Initialization Regiser (PMIR). Update the defines
to reflect the documentation.
Additionally, there is no core well reset control according to the
EDS. There is, however, a CF9 lock field to lock this register down.
Change-Id: I773c33bec63a06cdb869eb9f94553d476e492798
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2619
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME9 requirements have added some registers and changed some
of the MBP state machine. Implement the changes found so far in
the ME9 BWG. There were a couple of reigster renames, but the
majority of th churn in the me.h header file is just introducing
the data structures in the same order as the ME9 BWG.
Change-Id: I51b0bb6620eff4979674ea99992ddab65a8abc18
Signed-Off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2620
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The IA32_ENERGY_PERFORMANCE_BIAS MSR can only be read or written
to if the CPU supports it. The support is indicated by ECX[3] for
cpuid(6). Without this guard, some Haswell parts would GP# fault
in this routine.
No more GP# while running on haswell CRBs.
Change-Id: If41e1e133e5faebb3ed578cba60743ce7e1c196f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2639
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
In order for coreboot to assign resources properly the pci
drivers need to have th proper device ids. Add the host controller
and the LPC device ids for Lynx Point.
Resource assignment works correctly now w/o odd behavior because
of conflicts.
Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The reference code sends the dram init done command to the ME.
Therefore, there is no need for coreboot to do this.
Change-Id: I6837d6c50bbb7db991f9d21fc9cdba76252c1b7b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2633
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Even though this is under the graysreef board it really
applies to the Basking Ridge board. A subsequent patch will
rename graysreef to baskingridge.
The GPIO pins were updated to reflect the Basking Ridge schematics
as well as the DIMM spd addresses and USB over current pins.
Change-Id: Ice4e05f5203de3024cd463dfccf0bcfec1e247c1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2632
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a FIXME about checking a MCHBAR register that isn't setup yet.
Also, remove revision updating because I can't find anything in the
docs that suggest this is required for haswell.
Change-Id: Ia8a6e08f82e18789e31c6c2ec2c1d63740c18dc4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2631
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change the hard coded values in udelay.c to use the #defines
for MSRs and BCLK.
Change-Id: I2bbeb0b478d2e3ca155e8f82006df86c29a4f018
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2629
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Grays Reef is one of Intel's CRBs for the Haswell processor. The
platform is named Shark Bay.
GPIOs were the main focus so IRQ routing and ACPI still needs to be
further looked at.
Change-Id: Ie94b7af66f772714992a92612c76ca93b9b27088
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2621
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the steps outlined in the BWG.
It seems this is a lot simpler now (so far) which is good.
To test, boot to chromeos with 3.7 kernel + i915.preliminary_hw_support=1 and
see that the i915 driver complains a lot less than before and that a
splashscreen is displayed.
Change-Id: I722c90ecd351860949cedab24533f6c10e5b90e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2696
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This follows the new method outlined in the LPT BWG.
It is also very pedantic about its operation so it
is easier to read and compare against the docs and
the reference code implementation.
Change-Id: I235d634cded0c75ec0e9f53488f5b366107a18fa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2694
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for SMM modules by leveraging the RMODULE lib. This allows
for easier dynamic SMM handler placement. The SMM module support
consists of a common stub which puts the executing CPU into protected
mode and calls into a pre-defined handler. This stub can then be used
for SMM relocation as well as the real SMM handler. For the relocation
one can call back into coreboot ramstage code to perform relocation in
C code.
The handler is essentially a copy of smihandler.c, but it drops the TSEG
differences. It also doesn't rely on the SMM revision as the cpu code
should know what processor it is supported.
Ideally the CONFIG_SMM_TSEG option could be removed once the existing
users of that option transitioned away from tseg_relocate() and
smi_get_tseg_base().
The generic SMI callbacks are now not marked as weak in the
declaration so that there aren't unlinked references. The handler
has default implementations of the generic SMI callbacks which are
marked as weak. If an external compilation module has a strong symbol
the linker will use that instead of the link one.
Additionally, the parameters to the generic callbacks are dropped as
they don't seem to be used directly. The SMM runtime can provide the
necessary support if needed.
Change-Id: I1e2fed71a40b2eb03197697d29e9c4b246e3b25e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2693
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The vboot_handoff structure needs to be parsed from the coreboot tables.
Add a placeholder in sysinfo as well as the ability to parse the
coreboot table entry concering the vboot_handoff structure.
Built with unified boot loader and ebuild changes. Can find and use
the VbInitParams for doing kernel selection.
Change-Id: If40a863b4a445fa5f7814325add03355fd0ac647
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2720
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In their current macro form, any arguments that are expressions will be
evaluated multiple times. That can cause problems if they have side effects,
and might not even compile if the overall expression is ambiguous, for
instance if you pass in foo++.
Built with code that previously wouldn't compile because the macros
expanded to ambiguous expressions.
Change-Id: I378c04d7aff5b4ad40581930ce90e49ba7df1d3e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2719
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The timekeeping code in libpayload was dependent on rdtsc, and when it was
split up by arch, that code was duplicated even though it was mostly the same.
This change factors out actually reading the count from the timer and the
speed of the timer and puts the definitions of ndelay, udelay, mdelay and
delay into generic code. Then, in x86, the timer_hz and timer_get_raw_value
functions which used to be in depthcharge were moved over to libpayload's
arch/x86/timer.c. In ARM where there isn't a single, canonical timer, those
functions are omitted with the intention that they'll be implemented by a
specific timer driver chosen elsewhere.
Change-Id: I9c919bed712ace941f417c1d58679d667b2d8269
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2717
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is static and not used in that file. To avoid the compiler
complaining about that fact, put the two functions and the call to dump_ed
(currently #if 0) behind #ifdef USB_DEBUG
Change-Id: Ic373313b5fff81f09800f286b32238350ab699c6
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a bootblock.c file for the northbridge and setup the
PCIEXBAR as the first thing using IO PCI config acceses.
After that all PCI config accesses can use MMIO.
Change-Id: I51d229c626c45705dda1757c2f14265cbc0e6183
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2617
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
'for' loop initial declarations are only allowed in C99 mode
I didn't realize we don't enable 14 year old features when building
libpayload, and I must have accidentally not rebuilt everything when making my
final tweaks to my earlier change.
Change-Id: I6caeeffad177b6d61fa30175f767e85084c061f4
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2718
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
The original code attempted to reserve a space in RAM for coreboot to
remain resident. This turns out not to be needed, and breaks things
for the kernel since the exynos5250-smdk5250 kernel device tree starts
RAM at 0x40000000.
(This patch was originally by Gabe, I'm just uploading it)
Change-Id: I4536edaf8785d81a3ea008216a2d57549ce5edfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2698
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Change the OSC method to actually grant control of
PCIe capabilities to the OS instead of granting no
control. I believe the logic was backwards in the
original commit. Bits should be set when granting
control and cleared when not granting control. By
setting the return value to 0x00, we effectively
tell the OS that it cannot control any PCIe
capability. See section 6.2.9 of the ACPI spec
version 3.0 for more information.
This edit is a duplication of the OSC method that
is in the src/southbridge/intel/bd82x6x/pch.asl
file.
Change-Id: Id2462ab12203afceb9033f24d06b4dfbf2236d2e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2714
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Use memcpy to access a uint32_t that's inherently unaligned due to the layout
of the LZMA header format.
Built and booted on Daisy and saw a data abort go away. Built and booted
into developer mode on Link and verified that bitmaps were
decompressed/displayed correctly.
Change-Id: Id3ae746c04d23bcb0345cb71797bfa219479cc8f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2670
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some new TPM drivers in depthcharge require that type. I added it to
arch/types.h which seemed appropriate, but I'm not sure that's exactly the
right header to use, or in other words if you'd get that type from libpayload
the same way you'd get it if you were building a standard Linux program.
Also, I attempted to determine what underlying types gcc would use, and while
I think I picked the right ones I'm not 100% certain of that either.
Change-Id: Ic5c0b4173c8565ede3bfce8870976d596d69e51d
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2669
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Don't keep using the coreboot stack on ARMv7.
Change-Id: I734c5d77f8584e30ee0c720d41e21e3040f56db4
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2668
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables branch prediction. We can probably find a better place
to do this, but for now we'll do it in snow's romstage main().
Change-Id: I86c7b6bc9e897a7a432c490fb96a126e81b8ce72
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2701
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: Ia85a7cd6a0b85119cce6b2f9c42a7fc31ffd9f97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2654
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It might be useful to provide a USB driver in the payload itself instead of in
libpayload. For example there are multiple payloads being built and linked
against the same libpayload, and they might not need or even want to have the
same set of drivers installed.
This change adds two new functions, usb_generic_create and usb_generic_remove,
which behave like the usbdisk_create and usbdisk_remove functions which are
defined for USB mass storage devices. If a USB device isn't recognized and
claimed by one of the built in USB class drivers (currently hub, hid, and msc)
and the create function is defined, then it will be called to give the payload
a chance to use the device. Once it's removed, if usb_generic_remove is
defined it will be called, effectively giving the payload notice.
Built and booted depthcharge on Link. Built depthcharge for Daisy. Built
a netbooting payload, called usb_poll() with those functions implemented, and
verified that they were called and that the devices they were told about were
reasonable and the same as what was reported by lsusb in the booted system.
Change-Id: Ief7c0a513b60849fbf2986ef4ae5c9e7825fef16
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2666
Tested-by: build bot (Jenkins)
Reviewed-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Duncan Laurie