- Use newer functions and avoid the * / KiB dance
- Use existing functions for figuring out TSEG and UMA
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I73549b23bd1bfd4009e6467a5bdfeef7de81a0cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76272
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In the JPEG decoder, use `bytes_per_line` instead of `width` for
address calculations, to allow for bigger framebuffers. When
calling jpeg_decode(), add an offset to the framebuffer address
so the picture gets centered.
Change-Id: I0174bdccfaad425e708a5fa50bcb28a1b98a23f7
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Factor out all functions that use the indirect IO port based access to
the PM registers into a new compilation unit and only select it on
platforms that support this interface.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If9c059e450e2137f7e05441ab89c1f0e7077be9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
In all SoC pm_set_power_failure_state gets called either after a call to
enable_acpimmio_decode_pm04() or the ACPIMMIO mapping is already enabled
after reset on the SoC. This allows to use pm_read8 and pm_write8 that
use the ACPIMMIO mapping of the PM registers instead of pm_io_read8 and
pm_io_write8 which won't work on Phoenix and Glinda due to the IO ports
used on older generations to access to the PM registers not being
implemented any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0d0523d2c4920da41b3fb73cf62f22a60f1643a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Use pm_io_write8 instead of open coding the same functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1d9397f2d85e48883f961adbbca0e1e71e825ce0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
rv32iafc-ilp32 is compatible with rv32iac-ilp32 for library
implementation, so add a reuse rule allowing the default configuration
to support rv32iafc.
-IAFC is an unusual configuration (much less common than -IMAFC),
but multilib reuse has essentially no cost: this change is useful to
users of platforms that support hardware floating-point but cannot
use hardware multiply/divide for any reason. To avoid generating a
new set of libraries this is limited to the soft-float ABI.
Tested by verifying that `gcc -march=rv32iafc -mabi=ilp32
--print-search-dirs` refers to the rv32iac/ilp32 library directory
as expected, rather than just the root library directory as occurs
when an unsupported target is selected (for instance, rv32id).
Change-Id: Ie056ba6488a138fe0876eebf7cbc59477b3c3518
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
In all SoC lpc_early_init gets called either after a call to
enable_acpimmio_decode_pm04() or the ACPIMMIO mapping is already enabled
after reset on the SoC. This allows to use pm_read8 and pm_write8 that
use the ACPIMMIO mapping of the PM registers to set the PM_LPC_ENABLE
bit in the PM_LPC_GATING register instead of pm_io_read8 and
pm_io_write8 which won't work on Phoenix and Glinda due to the IO ports
used on older generations to access to the PM registers not being
implemented any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8b31ec4e03a06796502c89e3c2cfaac2d41b0ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76461
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
None of the platforms that used enable_acpimmio_decode_pm24 is in the
tree any more, so drop this function.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iea345a825c4581bf2acb932692ebcad2a7a5b4ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
The enable_acpimmio_decode_pm04 function uses the IO port based indirect
access of the PM register space. The PM_INDEX and PM_DATA registers
don't exist any more on Glinda, so the code shouldn't access those.
Since the PM_04_ACPIMMIO_DECODE_EN bit in the
ACPIMMIO_DECODE_REGISTER_04 register is 1 after reset, the ACPIMMIO
space is still accessible.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic6bc0479ea4ea2b9fe3629a6e15940b31b2864d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
The enable_acpimmio_decode_pm04 function uses the IO port based indirect
access of the PM register space. The PM_INDEX and PM_DATA registers
don't exist any more on Phoenix, so the code shouldn't access those.
Since the PM_04_ACPIMMIO_DECODE_EN bit in the
ACPIMMIO_DECODE_REGISTER_04 register is 1 after reset, the ACPIMMIO
space is still accessible.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia41f239b023edc094f5cbae63ed7c079649c74da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76437
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch disables early EC sync to avoid an idle delay (~3sec)
without a provision to notify the user about some critical task
in progress.
Doing EC sync at later stage allows us to notify using graphical msg
on screen to make user aware of the WIP task.
BUG=b:279944831
TEST=Able to perform EC sync from depthcharge on google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I03ed40827c50e75ceaaf94e30d675014ebf22dac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Disable DMI link ASPM which can degrade performance of overall system.
Desktop does not need to be concerned that much about idle power
consumption.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I60af9d2ab2913db449059e1e007999fa2f307f5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69826
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allows the new Infineon TPM chip used on Clevo laptops to be recognized.
Change-Id: I2ee31b787d80c0b9c24c748b1b28906a22a1dee7
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Create the craaskov variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:290248526
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_CRAASKOV
Change-Id: I1d12f7c3d0ef7067f4530c1c69c560f9a83561f6
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Add support for AP initiated mode entry. The code flow has been
optimized as below -
Code flow when AP initiated mode entry is disabled:
+-------+
| Start |
+---+---+
|
|
+---------+---------+
|wait_for_connection|
| Is DP ALT mode |
| available? |
+---------+---------+
|
+--------------->-------+
Yes| No |
+---------+---------+ |
|Skip enter_dp_mode | |
+---------+---------+ |
| |
| |
+-----------+----------+ |
|wait_for_dp_mode_entry| |
| Is DP flag set? | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| wait_for_hpd | |
| Is HPD_LVL flag set? | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| Rest of the code | |
+-----------+----------+ |
| |
+---------------<-------+
|
+---+---+
| End |
+-------+
Code flow when AP initiated mode entry is enabled:
+-------+
| Start |
+---+---+
|
+------------+-----------+
|Skip wait_for_connection|
+------------+-----------+
|
+--------+-------+
| enter_dp_mode |
| Is USB device? |
+--------+-------+
|
+--------------->-------+
Yes| No |
+---------+---------+ |
| enter_dp_mode | |
| Send DP mode | |
| entry command | |
+---------+---------+ |
| |
+-----------+----------+ |
|wait_for_dp_mode_entry| |
| Is DP flag set? | |
| (If not, loop wait | |
| until timed out) | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| wait_for_hpd | |
| Is HPD_LVL flag set? | |
| (If not, loop wait | |
| until timed out) | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| Rest of the code | |
+-----------+----------+ |
| |
+---------------<-------+
|
+---+---+
| End |
+-------+
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Time taken by enter_dp_mode / wait_for_dp+hpd / MultiPhaseSiInit
functions with this patch train:
1. When AP Mode entry is enabled
- With type-c display on C1 and SuzyQ on C0: 6.9ms / 420ms / 616ms
- With USB key on C1 and SuzyQ on C0 : 6.0ms / 505ms / 666ms
- Without any device on C1 and SuzyQ on C0 : 3.7ms / 0ms / 178ms
2. When AP Mode entry is disabled
- With type-c display on C1 and SuzyQ on C0: 1.7ms / 2.5ms / 213ms
- With USB key on C1 and SuzyQ on C0 : 0.9ms / 3.3ms / 177ms
- Without any device on C1 and SuzyQ on C0 : 0.8ms / 1.8ms / 165ms
Without this patch train, wait_for_hpd would cause a constant delay of
WAIT_FOR_HPD_TIMEOUT_MS (i.e. 3 seconds) per type-c port when there is
no device connected.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I514ccbdbaf905c49585dc00746d047554d7c7a58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Split wait-loop for DP and HPD flags as below -
- google_chromeec_wait_for_hpd
- google_chromeec_wait_for_dp_mode_entry
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3e565d6134f6433930916071e94d56d92dc6cb06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76370
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Wait for DP/HPD flags only in AP initiated mode entry
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I5137c346fbf1edabc60a53e0978e32f54885c330
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76369
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Skip TCSS `wait_for_connection` for AP initiated mode entry.
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ia04ff470961831237fe851f7ae3feaa5623d4b4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76368
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Skip TCSS `enter_dp_mode` command when there is no USB device detected
on the port.
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ie6cd84cab3631596d4d7178dae2040e25c621f63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
The PRESERVE flag in the FMD file tells futility not to erase the
fmap partition when updating the firmware. Because of an issue on
myst right now, we want the RW_MRC_CACHE partition to be erased
when the firmware is updated.
BUG=b:290763369
TEST=None
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id586ae057b2fd6d513ddbba5e1284dea39467d95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76478
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Phoenix doesn't have an eMMC controller and those UPDs were carried over
from Picasso. The SoC's fsp_m_params.c didn't write to any of those
fields, so this doesn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie3640c1493a92c1effba3ce42103d022bd8399ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Because of the way that the CBFS filename is generated from the contents
of the microcode patch, if a duplicate microcode patch is included in
the build, the makefile would create a second copy of the name, which
doesn't work. This led to "odd" results where the other attributes of
the first copy were erased, causing cbfstool to fail. The cause of the
failure is not immediately obvious, and is a little difficult to track
down.
This patch causes an immediate failure and gives a reason as to the
cause of the issue.
When a failure is seen, this is the result:
File1: 3rdparty/amd_blobs/phoenix/psp/TypeId0x66_UcodePatch_PHXn4_A0.bin
File2: 3rdparty/amd_blobs/phoenix/psp/TypeId0x66_UcodePatch_PHX4_A0.bin
src/soc/amd/common/block/cpu/Makefile.inc:25: *** Error: The cbfs
filename "cpu_microcode_a740.bin" is used for both above files. Check
your microcode patches for duplicates.. Stop.
TEST=Now checked for both positive and negative failures.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I3d34dc5585182545bdcbfa6370ebc34aa767cae2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76423
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
System76 boards use the VBT data file, not the VGA optionrom.
Change-Id: Ie4100e09221ae4f301a621e7aac62e38ac04a444
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
There is a data abort in ABL when the memory training data is used from
APOB Cache. Disable APOB Cache until the cause is identified. The
downside of this change is that the memory training happens in every
boot cycle.
BUG=b:290763369
TEST=Build BIOS image and boot to OS in Myst. Trigger a reboot from AP
console and ensure that the system boots to OS.
Change-Id: I20f4f40cdaac68bca6e121e3a238d13fe80d0d3c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
The dxio_port_param_type enum was copied over from Cezanne, but the enum
on the AGESA/FSP side changed between the generations. Add a TODO as a
reminder that this needs to be updated.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8063ab00a508b045265bab73197c8ca117622800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76448
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the proper dxio_link_hotplug_type enum values for the link_hotplug
field in the DXIO descriptors to replace the magic values in the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb1513737e6022a668287dc80a39d96cda2b18d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76439
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the dxio_link_hotplug_type enum definition for the link_hotplug
field in the DXIO descriptor struct.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieeb3e3edaed2c689707edc4df7d25c777005fde2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The dxio_port_param_type enum was copied over from Cezanne to Mendocino
to Phoenix, but the enum on the AGESA/FSP side changed between the
generations. Update the definition to match the definition used in the
Phoenix FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3c87fdc8bf0849d797c2af74c1d1495c7d85019f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76447
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dxio_port_param_type enum was copied over from Cezanne to Mendocino,
but the enum on the AGESA/FSP side changed between the two generations.
Update the definition to match the definition used in the Mendocino FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c4d7e4e3eaf7af9a43007363135412633c7440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76446
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Use newer functions and avoid the * / KiB dance
- Use existing functions for figuring out TSEG and UMA
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic6f42053b5303151906360d8512b9d63dd297854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76249
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The OxPCIe952 serial cards currently fails after entering
postcar, since the state of oxpcie_present is not maintained
from previous stage.
As a quick work-around test the expected UART register space
to see if anyone decodes the address.
Change-Id: I5601034be6e413616fb3433c894fb008a3e02138
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74597
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change `CBFS_SIZE` to match the actual BIOS region size, as specified in
the FIT XML config.
Fixes building with `VALIDATE_INTEL_DESCRIPTOR` selected.
Change-Id: I91a46b3ed6cc3161df27eed19d8cdf2820e90d7e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76326
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It moves cr50_plat_irq_status() to common code and adds Kconfig
option to specify GPIO used for interrupt.
BUG=b:277787305
TEST=Build all affected platform and confirm using right GPIO
number. Tested on Skyrim.
Change-Id: I775c4e24cffee99b6ac3e05b58a75425029a86c8
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75621
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
The file for Mendocino and Phoenix still used Cezanne in the comment and
from the file it's already clear to which SoC generation this belongs,
so just drop the SoC name from the comment.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I73e8b01e46904578226bb64e5e4659016c491880
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76440
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Arthur Heymans