Set numerous pads to PAD_NC as per board schematics (they are either
NC, or connected to test pads), and adjust comments as needed.
Change-Id: I4c2ab936256d0031d7a127fbeac42c8951a0b39f
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
These are generated by inteltool + intelp2m and reflect the
pad configuration of the vendor (AMI) firmware at a specific
point in time, but do not always reflect the correct configuration
of a given pad as per the schematics, so drop them.
Change-Id: Ie337cca5bc0e87a5426cceae8d7ec29ab14a1729
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47200
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since the Librem Mini does not run on battery power, SaGv has little
benefits and noticeably slows down testing, since memory training is
run twice. Disabling SaGv cuts the 30-second cold boot time in half.
Change-Id: Ib02e42dcb4f20fdbdca85456c0dceafc59c782d8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
These add nothing useful to the GPIO config
Change-Id: Ieecc9bd67d020e141c3a1f1d387034df5e563068
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47190
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update GPIO config using a fresh dump of inteltool from the
vendor (AMI) firmware on a Librem Mini v2, run through intelp2m
with parameters '-p cnl -n -ii'
Change-Id: I747415fb9ab7b21943d256d248729cb9e2b4b945
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47206
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move registers under devices to which they belong.
Change-Id: I61ca7c1db02646252d7421f8b79dfc8a40b2bdb5
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47188
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
this should have been corrected as part of:
commit 3de90d1 [soc/intel/cnl: Set Heci1Disable depending on devicetree config]
Change-Id: I6a103a1de01fc258ef359258a8a64f4c5a181139
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47187
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PL2 was set artificially low during development when the active cooling
fan was not functional, and never corrected once the fan was fixed.
Raise PL2 to a value which works with both Librem Mini variants.
Change-Id: Ie377392020f73359aed80ddae727adb6f8d06344
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
All chip registers default to 0, no need to explicitly set them.
Change-Id: I056121170d22393484b0ee79bd0815452161a900
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
- Move the SoC select to board config (vs baseboard config)
- Qualify the VGA PCI ID and CBFS size values based on board selection
- Move devicetree to variant dir and add Kconfig entry
- Use a separate board_info.txt for the baseboard and each variant
Change-Id: I4764f2c1243ea49bd08e0735865cc3cb7a66441f
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Since Whiskeylake SoC code is actually a subset of soc/intel/cannonlake,
rename the baseboard so that boards using other 'cannonlake family' SoCs
(e.g., Cometlake) can be added with minimal confusion.
Rename the mainboard dir and baseboard name, and adjust any references
to them.
Change-Id: I2af7977f1622070eb8bf8449bc8306f9d75b9851
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
