Fine tune usb 2.0 strength for port 4 to pass eye diagram.
BUG=b:65306272
TEST=build on soraka, measure usb2.0 eye diagram, and result is pass.
Change-Id: I2c79e96e2e3dea1364d7b71af19b57f4c9307fcb
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The RO_VPD region is required for ChromeOS.
BUG=b:65408869
TEST=Build and check coreboot.rom with fmap_decode.
Change-Id: I9c475acc5e34a3a41f815990fb1f363963c7b9b9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We've decided to move control for the 3.0V rail (technically 3.3V on
Scarlet, but who cares about millivolts) back to a GPIO on the AP for
Scarlet rev2. This patch adds the necessary code to enable it and make
ARM TF aware of its existence. Since the pin had previously not been
connected to anything, we shouldn't really need to guard this by board
ID... older Scarlets will just be twiddling an empty pin.
Change-Id: I6037aa486b50119f2c7b859b966cadc3686e3459
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/21328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
This patch adds imon and vmon slot numbers for Maxim 98927 driver.
These values are used to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I4382da4f984507d147751c168e8177b58c88a70f
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently PMIC (tps68470) is in active state even when cameras are not
in use. PMIC is put into SLEEP mode only when entering S3 via
smihandler.
With this change PMIC will be put into SLEEP mode as soon as sensors &
VCM voltage outputs are turned off. This will allow run time power
saving when camera is not in use.
PMIC will be reset in first boot & across S3 & S0ix cycles.
Also, remove the smi handler for PMIC power management & handle it as
part of sensor and VCM ACPI PowerResource.
BUG=b:63903239
TEST= Build for Soraka. Check Camera probe, Capture image across
S3 & S0ix cycles.
Also checked the following & found no regression:
1. Typical camera use cases
2. Stability tests related to camera
3. Reliability tests related to camera
4. PnP tests related to camera
5. Latency related tests with camera
Change-Id: I23b0c0a887c9eb5d29b89f14aebba273b01228e0
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds the DPTF settings specfic to the mainboard and enables
the CPU and other thermal sensors as participant device for fizz.
It also enables the DPTF flag in the device tree for fizz.
BUG=b:64915426
BRANCH=None
TEST=emerge-fizz coreboot and run DPTF observation tool to make sure
DPTF is up and running.
Change-Id: Ic7d125a763f539158aa425fbba1d8a000a3465ca
Signed-off-by: Tsai, Gaggery <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/21147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
We have no wacom digitizer on I2C#3, so remove it.
TEST=build and boot on soraka.
Change-Id: I3f5a1b9ece6fc9a9443477c7a7aa77dbcdf6a703
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21309
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do not assert GPIO1_B3 otherwise BT would be disabled on Nefario.
Also, remove DVS support for CENTERLOGIC.
BUG=b:64702054, b:63537905
TEST=build coreboot
Change-Id: I350db2c080f2e41ae56413f5f895557978ef0ba8
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/21176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
BUG=b:64987428
TEST=Verified that touchscreen works on boot-up and after
suspend/resume. No power leakage via stop gpio in suspended state.
Change-Id: Ia260eb444081dbe1646c90e82c2725661e7306bc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
We no longer use this touchscreen device, so get rid of it.
BUG=b:64987428
Change-Id: I67af787d231317a80998fb483eed5674de19aeb4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update cyan's SPD-related functions to more closely mirror
those of other Braswell boards, in order to simplify the upcoming
baseboard/variant setup for Braswell ChromeOS boards.
TEST: boot google/cyan, observe SPD correctly identified in
cbmem log, RAM-related data correct in SMBIOS tables.
Change-Id: Iafe99ec0795764f645e0a91f5b321be5b4c6fd88
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add a 16ms delay to DMIC init by the kernel driver in order to
prevent an audible 'pop' noise when starting to record.
BUG=b:63413023
TEST=manual testing to ensure this device property is present in SSDT:
Name (_DSD, Package () {
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package () {
Package () {
"realtek,dmic-init-delay",
0x10
}
}
})
Change-Id: If9160ce6992153ba49719029de336595bbf4ae72
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot
Change-Id: Ifdea897ef66dd10f29a8a0e72f9406d316fbe8c7
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/21233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tune I2C params for I2C buses 0, 1, 2, 4 and 5 to ensure that the
frequency does not exceed 400KHz.
BUG=b:35948024
TEST=Verified for 25 iterations that the frequency on each bus ranges
<= 400KHz.
I2C0: 375 - 400
I2C1: 377 - 400
I2C2: 377 - 400
I2C4: 375 - 397
I2C5: 375 - 397
Change-Id: Ie30e1a12b66c4660b648a585c4dfd66faf004129
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21208
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The LED polarity was set incorrectly, fix using values derived
from original Chromium sources:
branch firmware-mccloud-5827.B, ToT
src/mainboard/google/mccloud/smihandler.c
src/mainboard/google/mccloud/romstage.c
TEST: boot google/mccloud, observe power LED on normally,
blinking in S3/S4, and off in S5.
Change-Id: Ia1f63eebbccb48fcf8543188db390b23045d843e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Commit 0562783182 applied
this change to other Google boards, but cyan was left out.
Bring cyan in line with other Google boards.
Change-Id: Id86bea538a7b82367ea6ddbd3fe3efb1b1c0078d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Cleaning up code to remove support for pre-EVT rev of cyan board.
Analogous to what was done for intel/strago in commit 103f00d.
Change-Id: I29b32da8064e0743cc9c5df02ce7d3441459ee8f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit a162348.
Remove the hard coded IRQ number for the keyboard interrupt.
IRQ number can change based upon the gpio bank index ordering.
Hence pass the gpio bank and index number so that kernel calculates
the IRQ number.
Original-Change-Id: Icfe5c3995007164bf617575b541758c18ee63a1d
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I81ff19e3060c533ee76023c7651f741294e9db30
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit dc59188.
Disable L1 sub state to prevent WiFi randomly disappear condition.
Original-Change-Id: I8975bb4bbbc2fc89b91b06ae02716367890c672d
Original-Signed-off-by: T.H. Lin <T.H_Lin@quantatw.com>
Original-Reviewed-by: Rajat Jain <rajatja@chromium.org>
Original-Reviewed-by: Vincent Wang <vwang@chromium.org>
Oriignal-Tested-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Change-Id: I51a1bcca6431e6bc28baf9b09433cec13db925c3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit 1138727.
Elan touchscreen driver expects the first gpio resource in asl
to be the reset line.
The driver considers the gpio based irq line as reset gpio resource
and changes the direction to output.
This will cause irq registration to fail.
Solution is to pass Interrupt resource for touchscreen irq
instead of GpioInt.
Original-Change-Id: Ia72d4ad80117f3c0014098113c9027416026e65e
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I1c4b029851e321feeedf713186976fbec42dd82e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit e49deb1.
Configuring UPD PcdCaMirrorEn. This is a board specific parameter.
CA mirror is the Command Address mirroring option that is board
specific.
Original-Change-Id: I05174e18d650332d838e5036c713e91c4840ee75
Original-Signed-off-by: Divya Sasidharan <divya.s.sasidharan@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Change-Id: Ibd0c811d41cb592634f7785edb83ad2f423546c5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to provide new config options to perform LPC and SPI
lock down either by FSP or coreboot.
Remove EISS bit programming as well.
TEST=Build and boot Eve and Poppy.
Change-Id: If174915b4d0c581f36b54b2b8cd970a93c6454bc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to pass type C USB2 eye diagram for sku Santa,
USB2 port#1 PHY register needs to be overridden.
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 2
BUG=b:64880573
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage
Change-Id: I07c0b7b0f08263a348befb7d6fd8d01028314470
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Sync file with southbridge/amd/common/sleepstates.asl.
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Change-Id: I674953f1a5add74e16ddd84c252e8d21501ffefd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Kahlee has an ambient light sensor connected to the EC.
TEST=Can see the device in /sys/bus/iio
BUG=b:62030268
Change-Id: Id1138a0fc5270489a734bdf8b1f4ac02d358c0df
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/21146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch assigns the code of coral family, such that,
the 'mosys platform family' returns 'Google_Coral'.
BUG=b:64467244, b:64501879
BRANCH=none
TEST=Examine 'mosys platform family' w/ new firmware.
Change-Id: I1d8f8ca2166a1d80855608cf5b64b0cc7bf3dc93
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/21136
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64821783
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I8852e38f01f82b80c2c9718b93baf5894dbd745b
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Current coreboot does not create ACPI device for OS to recognize MELFAS
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64779224
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: If2bc910d641e0cf2b120ed883c5788542959f568
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Giantec semiconductor GT24C16S and ON semiconductor CAT24C16
are the industrial standard electrically erasable programmable
read only memory (EEPROM's) and this patch adds ACPI objects
and power resources for NVMEM device.
Update DOVD method to set sensor IO LDO voltage and remove repetitive
code from OVFI, VCMP and NVMP power resources.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Read the NVMEM content via sysfs interface.
Change-Id: If49ed33b7e1de1eabf317b31ceed8568dfca0aae
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage and verify the keyboard
backlight can be bright and alt+f6, alt+f7 function keys can be used.
Change-Id: I777247a6b58d3d50b72f12ca2fcab49a06ed5431
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/21027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I96a0e030bbc5f1c98165e70353340c413f8dc352
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add LPC common code to be shared across Intel platforms.
Also add LPC library functions to be shared across platforms.
Use common LPC code for Apollo Lake soc. Update existing Apollolake
mainboard variants {google,intel,siemens} to use new common
LPC header file.
Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Simplify funciton names and remove reference to hudson in stoneyridge.
The southbridge in Stoney Ridge is Kern and hudson naming is
no longer accurate.
BUG=b:62200157
BRANCH=none
TEST=Build and booted on Kahlee.
Change-Id: Ide7a72dae69b881997101f1e37a1ac739901744d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20912
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating the common smihandler to handler gpi events which
originally were going to be left to each soc to handle. After
some more analysis the gpi handler can also be commonized.
Change-Id: I6273fe846587137938bbcffa3a92736b91982574
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/20917
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
some gpio irq need to set input pull initialization status
to guarantee to get the right irq trigger. let's add this argument
in gpio_input_irq() function
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I9b8e6497f07146dafdb447a6ea10d039a2a2fa33
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
