mainboard directories, but the code was not referenced anywhere.
intel/jarrell
dell/s1850
supermicro/x6dhr_ig2
supermicro/x6dhr_ig
supermicro/x6dhe_g2
supermicro/x6dhe_g
Besides that, the contents of these files were either duplicates of
src/cpu/intel/model_f3x/microcode_M1DF340E.h or
src/cpu/intel/model_f3x/microcode_M1DF3413.h.
svn remove the following files:
src/mainboard/supermicro/x6dhe_g/microcode_updates.c
src/mainboard/supermicro/x6dhe_g2/microcode_updates.c
src/mainboard/supermicro/x6dhr_ig/microcode_updates.c
src/mainboard/supermicro/x6dhr_ig2/microcode_updates.c
src/mainboard/dell/s1850/microcode_updates.c
src/mainboard/intel/jarrell/microcode_updates.c
Abuild tested, as expected no failures.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3028 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
page size. Fix that. Page size is uniform 256 bytes for SPI.
A sector/block size field in struct flashchip would be nice, though.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
output is specified.
Pretty-print the chip status register (including block lock information)
for ST M25P family and Macronix MX25L family chips.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Bus 1, device 10 (function 0 only), routed to IO-APIC pin 18
(verified on an v1.0 board).
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's easier to tell users "copy your payload to /tmp/filo.elf" than have
them guess paths or modify Config.lb files etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3022 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Removed local APIC INIT (don't worry the APIC and AP are still initialized).
The local APIC INIT seemed to be the incorrect thing to do to stop an AP.
The Intel Multiprocessor specification indicated that a vector should be set
and a START should happen following an INIT. Then AP will execute the
instructions pointed to by the vector. There is no vector or start in
stop_this_cpu(). This seems to put the AP in an in-between state. In the case
of Barcelona the AP's MSRs and PCI register are not accessible by the hardware
debugger.
The better solution seems to be to just put the AP in a hlt and allow the AP
to go into C1. Then APIC managing software running on the BSP can program the
AP as needed.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3017 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Check that the SMBus controller is found and stop on an error.
Clean up and add additional path through the 8111 reset functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
These are the core files for HyperTransport, DDR2 Memory, and multi-core initialization.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3014 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3013 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
M25P64, M25P128 to flashrom. ST M25P80 support is already there.
Not tested, but conforming to data sheets and double checked.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
this is needed (at the very least) to make FILO work on these boards.
Disable UDMA/33 per default, which is slower but the safe choice, as we
don't know which IDE devices a user has attached, and some don't support
UDMA/33 very well or at all.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3010 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
with multiple possible opcodes from linear numbering at the end (_1, _2)
to include the opcode at the end (_60, _c7). That way, you only have to
take a short look at the data sheet and choose the right function by
appending the opcode listed in the data sheet.
No functional changes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Options.lb file that already had a "uses CONFIG_COMPRESSED_PAYLOAD_LZMA"
line in it.
I figure that only adding it to the files that already have support
for LZMA payloads makes sure I don't break anything.
Signed-off-by: Myles Watson <myles@pel.cs.byu.edu>
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3002 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
PC97317 has SID = 0xdf. PC87371/PC97371 do not seem to exist.
Signed-off-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2999 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coherent_ht.c (save one empty line removed) so there's no use
to keep it around.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, s/0xFF80/0xFFC0/ in the Acorp 6A815EPD board-enable, as per
http://www.linuxbios.org/pipermail/linuxbios/2007-December/027750.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2995 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Implement ISA related support:
- Initialize the RTC
- Enable access to all BIOS regions (but _not_ write access to ROM)
- Enable ISA (not EIO) support
- Without the *_isa.c file, the Super I/O init is never performed
- Improve IDE support:
- Add config option to enable Ultra DMA/33 for each disk
- Add config option to enable legacy IDE port access
- Implement hard reset support
- Implement USB controller support
- Various code cleanups and improvements
The code partially supports southbridges other than the 82371EB (but
which are very similar), more complete support will follow.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add missing contributors to the README.
- Drop obsolete -D option from manpage.
- Only list contributors who added non-trivial amounts of code as copyright
holders (and do not list those who merely provided register dump support
for Super I/Os). Those contributors are still listed in the README,
of course. See discussion in the thread starting at
http://www.linuxbios.org/pipermail/linuxbios/2007-October/025516.html
- Make a function static.
- Fix incorrect URL in code comment. Drop obsolete comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
according to mcqmcqmcq@fastmail.fm. Fix it.
Signed-off-by: Mondrian Nuessle <nuessle@uni-mannheim.de>
Acked-by: mcq <mcqmcqmcq@fastmail.fm>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the latest version (Rev. 3.73, October 2007) of the 'Revision Guide for
AMD Athlon 64 and AMD Opteron Processors' datasheet.
Also, add information about the CPU socket for each ID (as per datasheet).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2989 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It never worked in v2 (the v1 port did work AFAIK, though), and it's
not really useful as reference for other boards anymore (as we now
have a dozen or so 440BX boards which work in v2).
This is a specialized, custom board (not sold on the "public market"),
so it's probably not useful for pretty much everyone out there anyway.
We can easily re-add it later (based on one of the other 440BX boards)
should there be interest and/or someone with the hardware to test.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2988 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
You cannot set 'default ROM_SIZE = 0' in Options.lb (and override it in
targets/*/Config.lb). While it'll work for manual builds, abuild doesn't
cope with that very well. So set a valid value in Options.lb, too.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2981 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Carl-Daniel Hailfinger