In order to prepare the ramstage to be linked by the rmodule linker the
stack needs to be self-contained within the ramstage objects. The
reasoning is that the rmodule linker provides a way to define a heap,
but it doesn't currently have a region for the stack.
The downside to this is that memory footprint of the ramstage can change
when compared before this change. The size difference stems from the
link ordering of the objects as the stack is now defined within
c_start.S. The size fluctuation ranges from 0 to CONFIG_STACK_SIZE - 1
because of the previous behavior or aligning to CONFIG_STACK_SIZE. It
should be noted that such an alignment is unnecessary for 32-bit x86 as
the alignment requirement for the stacks are 4 byte alignment. Also the
memory footprint is still dominated by CONFIG_RAMTOP and CONFIG_RAMBASE.
Change-Id: I63a4ddd249104bc27aff2ab6b39fc6db12b54028
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2785
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
In certain situations boot speed can be increased by providing an
alternative implementation to cbfs_load_payload(). The
ALT_CBFS_LOAD_PAYLOAD option allows for the mainboard or chipset to
provide its own implementation.
Booted baskingridge board with alternative and regular
cbfs_load_payload().
Change-Id: I547ac9881a82bacbdb3bbdf38088dfcc22fd0c2c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2782
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
At some point, compiles with USB Debug port stopped working. This change makes
a trivial reordering in the code and adds two makefile entries to make it build
without errors. It also works on stout.
Build and boot as normal. Works. Enable CONFIG_USB, connect USB debug hardware
to the correct port (on stout, that's the one on the left nearest the back) and
watch for output.
Change-Id: I7fbb7983a19b0872e2d9e4248db8949e72beaaa0
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2784
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Change:
This is the initial step for moving the AMD F15 & HUDSON1,2,3
SPD-read callout out of the mainboard directories and into
the wrapper. The next step is to update the platforms to use
this routine in BiosCallouts.c and to delete the code from the
mainboard directories. The DIMM addresses should be moved into
devicetree.cb.
If there are significant differences or reasons that the mainboard
needs to override this code, it's perfectly reasonable to keep using
the version in the mainboard, but this allows us to remove duplicated
code and simplify the mainboard directories.
Notes:
This started by duplicating what was in Dinar, and was changed to
use the devicetree.cb structures. Significant cleanup and magic
number reduction was done as well.
It is intended that this file will not be included in ramstage as
the DIMM init is all done in romstage.
This is similar to what was done for Parmer/Thatcher in commit
7fb692bd - http://review.coreboot.org/#/c/2190/
Fam15tn: Move SPD read from mainboards into wrapper
Yes, it would make sense to split this into two separate files
and move the SMBus initialization and access into the southbridge
wrapper. Maybe that can come next.
Change-Id: I4e00ada288e1486cf30684403505e475f9093ec2
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2777
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
cbfstool usage change:
The "-a" parameter for "cbfstool locate" is switched to "-P/--page-size".
The "locate" command was used to find a place to store ELF stage image in one
memory page. Its argument "-a (alignment)" was actually specifying the page size
instead of doing memory address alignment. This can be confusing when people are
trying to put a blob in aligned location (ex, microcode needs to be aligned in
0x10), and see this:
cbfstool coreboot.rom locate -f test.bin -n test -a 0x40000
# output: 0x44, which does not look like aligned to 0x40000.
To prevent confusion, it's now switched to "-P/--page-size".
Verified by building i386/axus/tc320 (with page limitation 0x40000):
cbfstool coreboot.rom locate -f romstage_null.bin -n romstage -P 0x40000
# output: 0x44
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: I0893adde51ebf46da1c34913f9c35507ed8ff731
Reviewed-on: http://review.coreboot.org/2730
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
A fix to eliminate warnings when building romstage files with ChromeOS
compilers
Change-Id: Ia5d7bbdde3aa3439fd493f5795f2cc2bf4c4c187
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2781
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There should be a fixed 10ms wait after sending an INIT IPI. The
previous implementation was just waiting up to 10ms for the IPI to
complete the send. That is not correct. The 10ms is unconditional
according to the documentation. No ill effects were observed with the
previous behavior, but it's important to follow the documentation.
Change-Id: Ib31d49ac74808f6eb512310e9f54a8f4abc3bfd7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2780
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch parallelizes the AP startup for Haswell-based devices. It
does not touch the generic secondary startup code. Instead it provides
its own MP support matching up with the Haswell BWG. It seemed to be too
much trouble to support the old startup way and this new way. Because of
that parallel loading is the only thing supported.
A couple of things to note:
1. Micrcode needs to be loaded twice. Once before MTRR and caching is
enabled. And a second time after SMM relocation.
2. The sipi_vector is entirely self-contained. Once it is loaded and
written back to RAM the APs do not access memory outside of the
sipi_vector load location until a sync up in ramstage.
3. SMM relocation is kicked off by an IPI to self w/ SMI set as the
destination mode.
The following are timings from cbmem with dev mode disabled and recovery mode
enabled to boot directly into the kernel. This was done on the
baskingridge CRB with a 4-core 8-thread CPU and 2 DIMMs 1GiB each. The
kernel has console enabled on the serial port. Entry 70 is the device
initialization, and that is where the APs are brought up. With these two
examples it looks to shave off ~200 ms of boot time.
Before:
1:55,382
2:57,606 (2,223)
3:3,108,983 (3,051,377)
4:3,110,084 (1,101)
8:3,113,109 (3,024)
9:3,156,694 (43,585)
10:3,156,815 (120)
30:3,157,110 (295)
40:3,158,180 (1,069)
50:3,160,157 (1,977)
60:3,160,366 (208)
70:4,221,044 (1,060,677)
75:4,221,062 (18)
80:4,227,185 (6,122)
90:4,227,669 (484)
99:4,265,596 (37,927)
1000:4,267,822 (2,225)
1001:4,268,507 (685)
1002:4,268,780 (272)
1003:4,398,676 (129,896)
1004:4,398,979 (303)
1100:7,477,601 (3,078,621)
1101:7,480,210 (2,608)
After:
1:49,518
2:51,778 (2,259)
3:3,081,186 (3,029,407)
4:3,082,252 (1,066)
8:3,085,137 (2,884)
9:3,130,339 (45,202)
10:3,130,518 (178)
30:3,130,544 (26)
40:3,131,125 (580)
50:3,133,023 (1,897)
60:3,133,278 (255)
70:4,009,259 (875,980)
75:4,009,273 (13)
80:4,015,947 (6,674)
90:4,016,430 (482)
99:4,056,265 (39,835)
1000:4,058,492 (2,226)
1001:4,059,176 (684)
1002:4,059,450 (273)
1003:4,189,333 (129,883)
1004:4,189,770 (436)
1100:7,262,358 (3,072,588)
1101:7,263,926 (1,567)
Booted the baskingridge board as noted above. Also analyzed serial
messages with pcserial enabled.
Change-Id: Ifedc7f787953647c228b11afdb725686e38c4098
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2779
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch only applies to CONFIG_MICROCODE_IN_CBFS. The intel microcode
update routine would always walk the CBFS for the microcode file. Then
it would loop through the whole file looking for a match then load the
microcode. This process was maintained for intel_update_microcode_from_cbfs(),
however 2 new functions were exported:
1. const void *intel_microcode_find(void)
2. void intel_microcode_load_unlocked(const void *microcode_patch)
The first locates a matching microcode while the second loads that
mircocode. These new functions can then be used to cache the found
microcode blob w/o having to re-walk the CBFS.
Booted baskingridge board to Linux and noted that all microcode
revisions match on all the CPUs.
Change-Id: Ifde3f3e5c100911c4f984dd56d36664a8acdf7d5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2778
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Having this header file in the mainboard directory breaks
the dinar build on cygwin because the header file in the
dinar mainboard is used instead of the correct header file
src/vendorcode/amd/cimx/sb700/OEM.h. The build probably works
fine on Linux systems because, due to case-sensitivity, Oem.h
will not match the #include "OEM.h" statement in
src/southbridge/amd/cimx/sb700/Platform.h.
The Oem.h file in the dinar mainboard is not used by any other
source files, and the defines in the dinar mainboard are duplicated
by defines in the correct OEM.h file. Therefore, the file can be
safely removed.
Change-Id: I81b97eca8116d63644d335edc3bb51f90c7094d9
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2776
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
The non-relocatable SMM code was changed to link against libgcc a while back
so that printk could use built-in division instead of a hand crafted div()
function. However, the relocatable SMM code was not adapted by mistake.
This patch links the relocatable SMM against libgcc, too, so we can enable it
for Haswell.
Change-Id: Ia64a78e2e62348d115ae4ded52d1a02c74c5cea4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2727
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are changes coming to perform more complex tasks after cache-as-ram
has been torn down but before ramstage is loaded. Therefore, add the
romstage_after_car() function to call after cache-as-ram is torn down.
Its responsibility is for loading the ramstage and any other complex
tasks. For example, the saving of OS-controlled memory in the resume
path has now been moved into C instead of assembly.
Change-Id: Ie0c229cf83a9271c8995b31c534c8e5a696b164e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2757
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The save_mrc_data() was previously called conditionally
in the raminit code. The save_mrc_data() function was called
in the non-S3 wake paths. However, the common romstage_common()
code was checking cbmem initialization things on s3 wake. Between
the two callers cbmem_initialize() was being called twice in the
non-s3 wake paths. Moreover, saving of the mrc data was not allowed
when CONFIG_EARLY_CBMEM_INIT wasn't enabled.
Therefore, move the save_mrc_data() to romstage_common. It already has
the knowledge of the wake path. Also remove the CONFIG_EARLY_CBMEM_INIT
requirement from save_mrc_data() as well as the call to cbmem_initialize().
Change-Id: I7f0e4d752c92d9d5eedb8fa56133ec190caf77da
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2756
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of hard coding the policy for the stack and MTRR values after
the cache-as-ram is torn down, allow for the C code to pass those
policies back to the cache-as-ram assembly file. That way, ramstage
relocation can use a different stack as well as different MTRR policies.
Change-Id: Ied024d933f96a12ed0703c51c506586f4b50bd14
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2755
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit pulls in all the common logic for romstage into
the Haswell cpu directory. The bits specific to the mainboard
still reside under their respective directories. The calling
sequence bounces from the cpu directory to mainboard then back
to the cpu directory. The reasoning is that Haswell systems use
cache-as-ram for backing memory in romstage. The stack is used to
allocate structures. However, now changes can be made to the
romstage for Haswell and apply to all boards.
Change-Id: I2bf08013c46a99235ffe4bde88a935c3378eb341
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2754
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This structure is not used nor the variable being instantiated on the
stack. Remove them.
Change-Id: If3abe2dd77104eff49665dd33570b07179bf34f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2753
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It was found that the Haswell reference code was smashing through the
stack into the reference code's heap implementation. The reason for this
is because our current CAR allocation is too small. Moreover there are
quite a few things to coordinate between 2 code bases to get correct.
This commit separates the CAR into 2 parts:
1. MRC CAR usage.
2. Coreboot CAR usage.
Pointers from one region can be passed between the 2 modules, but one
should not be able to affect the others as checking has been put into
place in both modules.
The CAR size has effectively been doubled from 0x20000 (128 KiB) to
0x40000 (256KiB). Not all of that increase was needed, but enforcing
a power of 2 size only utilizes 1 MTRR.
Old CAR layout with a single contiguous stack with the region starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| MRC global variables |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+
| ROM stage stack |
| |
| |
+---------------------------------------+
| MRC Heap 30000 bytes |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
There was some hard coded offsets in the reference code wrapper to start
the heap past the console buffer. Even with this commit the console
can smash into the following region depending on what size
CONFIG_CONSOLE_CAR_BUFFER_SIZE is.
As noted above This change splits the CAR region into 2 parts starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+
| MRC Region |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| ROM stage stack |
| |
| |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
Another variable was add, CONFIG_DCACHE_RAM_ROMSTAGE_STACK_SIZE,
which represents the expected stack usage for the romstage. A marker
is checked at the base of the stack to determine if either the stack
was smashed or the console encroached on the stack.
Change-Id: Id76f2fe4a5cf1c776c8f0019f406593f68e443a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2752
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add an rmodules class so that there are default rules for compiling
files that will be linked by the rmodule linker. Also, add a new type
for SIPI vectors.
Change-Id: Ided9e15577b34aff34dc23e5e16791c607caf399
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2751
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is causing a hang in depthcharge. For now just disable
this port.
Change-Id: I87a6db2d8361588e82eee640c74cea690115bed5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2764
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The template had a dependency on config.h which was correct for coreboot,
where this build system originally came from, but not for libpayload which
uses the differently named libpayload-config.h, presumably to avoid colliding
with a config.h used by the actual payload. Because libpayload-config.h is now
effectively a dependency of everything, it doesn't have to be added piecemeal
in Makefile.inc.
Change-Id: I01f20d363cb1393fa1cdcf0dc916670db90294e9
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2763
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
And include the new, split out version in drivers/keyboard.c and
drivers/usb/usbhid.c. Those files were including curses.h just for those
definitions, but the include path was only fixed up to to point to the
libpayload versions of those files if one of the variants of curses was
compiled in. If neither was, gcc would fall back to the system version of that
header which is wrong.
Change-Id: I8c2ee0baf5f0702bd8c713c8dd4613a4bb269ce5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/2762
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
By including the heap in the bss output section the size is accounted
for in a elf PT_LOAD segment. Without this change the heap wasn't being
put into a PT_LOAD segment. The result is a nop w.r.t. functionality,
but readelf and company will have proper MemSiz fields.
Change-Id: Ibfe9bb87603dcd4c5ff1c57c6af910bbba96b02b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is a plan to utlize rmodules for loading ramstage as a
relocatable module. However, the rmodule header may change.
In order to provide some wiggle room for changing the contents
of the rmodule header add some padding. This won't stop the need
for coordinating properly between the romstage loader that may be
in readonly flash and rmodule header fields. But it will provide
for a way to make certain assumptions about alignment of the
rmodule's program when the rmodule is compressed in the flash.
Change-Id: I9ac5cf495c0bce494e7eaa3bd2f2bd39889b4c52
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2749
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Haswell's BCLK is fised at 100MHz like Sandy/Ivy. Add Haswell's model
to the switch statement.
Change-Id: Ib9e2afc04eba940bfcee92a6ee5402759b21cc45
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2747
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
A rmodule is short for relocation module. Relocaiton modules are
standalone programs. These programs are linked at address 0 as a shared
object with a special linker script that maintains the relocation
entries for the object. These modules can then be embedded as a raw
binary (objcopy -O binary) to be loaded at any location desired.
Initially, the only arch support is for x86. All comments below apply to
x86 specific properties.
The intial user of this support would be for SMM handlers since those
handlers sometimes need to be located at a dynamic address (e.g. TSEG
region).
The relocation entries are currently Elf32_Rel. They are 8 bytes large,
and the entries are not necessarily in sorted order. An future
optimization would be to have a tool convert the unsorted relocations
into just sorted offsets. This would reduce the size of the blob
produced after being processed. Essentialy, 8 bytes per relocation meta
entry would reduce to 4 bytes.
Change-Id: I2236dcb66e9d2b494ce2d1ae40777c62429057ef
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2692
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The acpi_fill_mcfg() was still using ivy/sandy PCI device ids which Hawell
obviously doesn't have. This resulted in an empty MCFG table. Instead of
relying on PCI device ids use dev/fn 0/0 since that is where the host
bridge always resides. Additionally remove the defines for the IB and SB
pci device ids. Replace them with mobile and ult Haswel device ids and
use those in the pci driver tables for the northbridge code.
Booted to Linux and noted that MCFG was properly parsed.
Change-Id: Ieaab2dfef0e9daf3edbd8a27efe0825d2beb9443
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2748
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM handler resides in the TSEG region which is far above
CONFIG_RAM_TOP (which is the highest cacheable address) before
MTRRs are setup. This means that calling initialize_cpus() before
performing MTRR setup on the BSP means the SMM handler is copied
using uncacheable accesses.
Improve the SMM handler setup path by enabling performing MTRR setup on
for the BSP before the call to initialize_cpus(). In order to do this
the haswell_init() function was split into 2 paths: BSP & AP paths.
There is a cpu_common_init() that both call to perform similar
functionality. The BSP path in haswell_init() then starts the APs using
intel_cores_init(). The AP path in haswell_init() loads microcode and
sets up MTRRs.
This split will be leveraged for future support of bringing up APs in
parallel as well as adhering to the Haswell MP initialization
requirements.
Change-Id: Id8e17af149e68d708f3d4765e38b1c61f7ebb470
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The configure_mca() function was hard coding the number of
banks the cpu supported. Query this dynamically so that it
no longer clears only 7 banks.
Change-Id: I33fce8fadc0facd1016b3295faaf3ae90e490a71
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2745
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This just moves the definiton of CORE_THREAD_COUNT_MSR so
that future code can utilize it.
Change-Id: I15a381090f21ff758288f55dc964b6694feb6064
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2744
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit adds support for using the SMM modules for haswell-based
boards. The SMI handling was also refactored to put the relocation
handler and permanent SMM handler loading in the cpu directory. All
tseg adjustment support is dropped by relying on the SMM module support
to perform the necessary relocations.
Change-Id: I8dd23610772fc4408567d9f4adf339596eac7b1f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We're happy to announce coreboot support for the "Stout"
Chromebook, a.k.a Lenovo X131e Chromebook.
Change-Id: I9b995f8d0dd48e41c788b7c3d35b4fac5840e425
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2636
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is mostly a copy of Whitetip Mountain 1 with specific GPIO
map for this Customer Reference Board (CRB).
This mainboard currently has basic funcionality and is able to
boot a Linux Kernel but many of the new Haswell ULT specific
devices are not yet enabled.
Change-Id: I999452d86f00a2c245fa39b1b76080f6a3b1e352
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2725
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Some initialization steps were done twice
- One step was missing for Panther Point HDA
- Added a 1ms delay after reset
- Increased timeout to 1ms for all codec operations
Change-Id: Ib751f1a16ccd88ea2fbbb2a10737f76277574026
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Haswell CPUs require a FIT table in the firmware. This commit
adds rudimentary support for a FIT table. The number of entries
in the table is based on a configuration option. The code only
generates a type 0 entry. A follow-on tool will need to be developed
to populate the FIT entries as well as checksumming the table.
Verified image has a FIT pointer and table when option is selected.
Change-Id: I3a314016a09a1cc26bf1fb5d17aa50853d2ef4f8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2642
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Lots of things are still placeholder and need work.
Due to the useful GPIOs being run to either the EC or the SIO1007
I have hard coded developer mode on and recovery mode off.
Change-Id: I4c308bd90db03ac5bffdfde566e5adbbaabac632
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2724
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Certain SATA devices claim to support SATA 6 Gbps, but in fact have
bugs. For these devices, add a config option to force the SATA link
speed to something other than default.
Change-Id: I2dc1793cd58771298a392345162d39d20eb0afbb
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables power management and clock gating on XHCI.
Change-Id: I124ea6c5aca034b7ec4b5286d971c2adfce25c88
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
objcopy -B provides symbols of the form _binary_<name>_(start|end|size).
However, the _size variant is an absoult symbol. If one wants to
relocate the smi loading the _size symbol will be relocated which is
wrong since it is suppose to be a fixed size. There is no way to
distinguish symbols that shouldn't be relocated vs ones that can.
Instead use the _start and _end variants to determine the size.
Change-Id: I55192992cf36f62a9d8dd896e5fb3043a3eacbd3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2760
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The bd82x6x requires some additional setting on S3/S4 entry.
Change-Id: I24489ab94dd7cd5a4a64044f25153f5b01a45b77
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2759
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the PCH function to SMM for follow-on SMM patches that
require these functions.
Change-Id: I7f3a512c5e98446e835b59934d63a99e8af15280
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2758
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMRR takes precedence over the MTRR entries. Therefore, if the TSEG
region is setup as cacheable through the MTTRs, accesses to the TSEG
region before SMM relocation are cached. This allows for the setup of
SMM relocation to be faster by caching accesses to the future TSEG
(SMRAM) memory.
MC MAP: TOM: 0x140000000
MC MAP: TOUUD: 0x18f600000
MC MAP: MESEG_BASE: 0x13f000000
MC MAP: MESEG_LIMIT: 0x7fff0fffff
MC MAP: REMAP_BASE: 0x13f000000
MC MAP: REMAP_LIMIT: 0x18f5fffff
MC MAP: TOLUD: 0xafa00000
MC MAP: BGSM: 0xad800000
MC MAP: BDSM: 0xada00000
MC MAP: TESGMB: 0xad000000
MC MAP: GGC: 0x209
TSEG->BGSM:
PCI: 00:00.0 resource base ad000000 size 800000 align 0 gran 0 limit 0 flags f0004200 index 4
BGSM->TOLUD:
PCI: 00:00.0 resource base ad800000 size 2200000 align 0 gran 0 limit 0 flags f0000200 index 5
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
Setting variable MTRR 1, base: 2048MB, range: 512MB, type WB
Setting variable MTRR 2, base: 2560MB, range: 256MB, type WB
Adding hole at 2776MB-2816MB
Setting variable MTRR 3, base: 2776MB, range: 8MB, type UC
Setting variable MTRR 4, base: 2784MB, range: 32MB, type UC
Zero-sized MTRR range @0KB
Allocate an msr - basek = 00400000, sizek = 0023d800,
Setting variable MTRR 5, base: 4096MB, range: 2048MB, type WB
Setting variable MTRR 6, base: 6144MB, range: 256MB, type WB
Adding hole at 6390MB-6400MB
Setting variable MTRR 7, base: 6390MB, range: 2MB, type UC
MTRR translation from MB to addresses:
MTRR 0: 0x00000000 -> 0x80000000 WB
MTRR 1: 0x80000000 -> 0xa0000000 WB
MTRR 2: 0xa0000000 -> 0xb0000000 WB
MTRR 3: 0xad800000 -> 0xae000000 UC
MTRR 4: 0xae000000 -> 0xb0000000 UC
I'm not a fan of the marking physical address space with MTRRs as being
UC which is PCI space, but it is technically correct.
Lastly, drop a comment describing AP startup flow through coreboot.
Change-Id: Ic63c0377b9c20102fcd3f190052fb32bc5f89182
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2690
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Devoutly to be wish'd. To die,—to sleep;—
To sleep! perchance to dream:—ay, there's the rub;
For in that sleep of death what dreams may come,
(Since who could argue with William Shakespeare?)
Change-Id: I4e4c617dcd3ede81a0abbe16f9916562d24fa8ce
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/2733
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I5184df8deb7b5d2e15404d689c16c00493eb01aa
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2736
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same chagne as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Id560ea85a38f73aaba2c35447bbce46bd9c0d0dd
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iae70c3d0af1cdaca31b206ad6daba4d38ee6b780
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iff594d4a3493531561eb25d1cceeb97bcefde424
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: Ie36b60973c6a5f9076bb55c8f451532711a2f8a8
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Aaron Durbin