Re-enable the SPD dump routine in this Bitworks/IMS code and make
it work like the Asus/p2b. This avoids having to hack the
sdram/generic_dump_spd.c for a single mem controller.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2352 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- New superIO winbond/w83977tf
- Add single memory controller SBbus debug routine
into a file private to the i440bx
This adds support the start of support for an Asus p2b
mainboard. Current limitations are the same as for the
Bitworks IMS board. Reads from the SMbus don't work.
Moving dump_spd_registers() into its own private copy
solves the problem of having to go hack on the version that
included in src/sdram to only do one memory controller.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2351 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There is one global change to pci_ids.h. The rest are changes for LX. I
ran abuild and it is ok. Not all artec design changes are included as
some of them would adversely affect other mainboards. Indrek will need
to test.
Signed-off-by: Ron Minnich
Signed-off-by: Indrek Kruusa, indrek.kruusa@artecdesign.ee, artec
design.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
UART. If the upper banks are enabled, then the Linux 8250 driver knows
how to set baud speeds greater then 115200. This was prompted by David
Woodhouse.
Jordan"
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add support for NSC pc87351 SuperIO
add Bitworks/IMS manboard config
This is a very basic framework for the i440bx chipset and the
Bitworks IMS board that uses it. Most things are
structure only.
Known issues:
- SMbus reads to the RAM SPD come back
all zero.
- dump_spd_registers() is commented out since it breaks with
the default setting of generic_dump_spd.c where it wants
2 memory controllers.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
https://openbios.org/roundup/linuxbios/issue55
This patch is a little bit enhanced, it keeps the ppc table consistent,
which Yinghai's original patch did not.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2342 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
breaking a build is intentional. It will be fixed in a bit.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2338 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
manage them. Make pci_level_irq global. Add value settings for OLPC
rev_a board. Comment out no-longer-needed code in olpc mainboard.c
-- it is replaced by the settings in Config.lb, and the support
in cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2328 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
olpc and rumba can now boot linux out of flash. vsa was resized to 64K.
olpc and rumba now used compressed payload -- thanks stefan!
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2307 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Richard Smith