While pushing the fsp_baytrail code, it was requested that we change
CONFIG_ENABLE_FAST_BOOT to CONFIG_ENABLE_FSP_FAST_BOOT.
These were missed in the change.
Change-Id: If8af3f90b0f5cc9154ff1d3a387f442430f42dee
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5972
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use the following command to fix all occurences.
$ git grep -l approriate | xargs sed -i 's/approriate/appropriate/g'
Change-Id: I4cbba972bb445c2407ef2e63ffb3068fc948f1c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5987
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Use the default mmconf base address and fsp locations.
Change-Id: Ia9116b0f0fc799592df2a10b10e086cfc88b394c
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5982
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The PCI_INTR table is an Index/Data pair of I/O ports
0xC00 and 0xC01. This table is responsible for physically
routing IRQs to the PIC and IOAPIC. The settings given
in this table are chipset and mainboard dependent, so the
table values will reside in the mainboard.c file. This
allows for a system to uniquely set its IRQ routing.
The function to write the PCI_INTR table resides in
cimx_util.c because the indices into the table have
the same definitions for all SBx00 FCH chipsets.
The next piece is a function that will read the PCI_INTR
table and program the INT_LINE and INT_PIN registers in
PCI config space appropriately. This function will read
a devices' INT_PIN register, which is always hardcoded to
a value if it uses hardware interrupts. It then uses this
value, along with the device and function numbers to
determine an index into the PCI_INTR table. It will read
the table and program the corresponding value into the PCI
config space register 0x3C, INT_LINE. Finally, it will set
this IRQ number to LEVEL_TRIGGERED on the PIC because it is
a PCI device interrupt and the must be level triggered.
For example, the SB800 USB EHCI device 0:18.2 has an INT_PIN
value hardcoded to 2. This corresponds to PIN B. On the
Persimmon mainboard, I want the USB device to use IRQ 11. I
will program the PCI_INTR table at index 0x31 (this USB device
index) to 11. This function will then read the INT_PIN register,
read the PCI_INTR table, and then program the INT_LINE register
with the value it read. It will then set the IRQ on the PIC to
LEVEL_TRIGGERED by writing a 1 to I/O port 0x4D1 at bit position 4.
Also, the SB700 has slightly different register definitions than
the newer SB800 and SB900 so it needs its own set of #defines for
the pci_intr registers.
Only the Persimmon mainboard is adapted to this change as an
example for other mainboards.
Change-Id: I6de858289a17fa1e1abacf6328ea5099be74b1d6
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/5877
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
S3 resume is expected to work now, however the 3s delay and flash wear
is still there.
Change-Id: I7edbce7bcf9c2160099fd5e371562b1ec63d45d8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5971
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
1. Remove #include .c in romstage.
2. Make romstage component symbols linker-time.
3. Provide header guards and prototypes in superio romstage support.
4. Correct function type-signatures to be static/non-static where
appropriate, avoid 'pretend optimisations' by unnecessarily inlining
functions.
5. Separate out UART enable from various other PNP hard coding
Change-Id: I9b8dad7c02d802e97db73ddf2913d5c6bb33a419
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5916
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Rewrite smsc/smscsuperio romstage component to be more consistent and
provide header there-by removing #include's of early_serial.c's in
mainboard's.
Change-Id: I572e0c76422f09d4de88935a36c0a59e5350e6e0
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5915
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
These non-ROMCC boards #include the model specific w83977tf Super I/O
romstage component. The generic winbond_early_serial() function serves
well here to further tighten integration into the new Super I/O
framework and drop dependence on #include'ing .c files, leaving only
ROMCC boards.
Change-Id: Ib63c0f29f994c54e6112702506f288535799706c
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5898
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Move samsung/stumpy board towards generic romstage component and away
from poorly written hard-coded model specific Super I/O component. This
is an incremental step towards getting obj-level abstraction between
board and Super I/O.
Change-Id: I358c5abef85c2ffa1b7178025cde8834a35b0a51
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5899
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The lock bit for UVSVC/LVSVC was set before both registers were programmed.
Change-Id: I000440db5c8dd2f260ebc1b69108b75621faf7b3
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5167
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Without it option ROM run results in just a black screen.
Change-Id: Id203f55ca0f02c290a3f40ac1ec7c5f23c5580bf
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5344
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
thinkpad_acpi checks that BIOS version matches some pattern.
Report version in this form.
Not cleaned up as the idea of this patch seems to be met with resistance.
Can make it Thinkpad-specific if the idea is accepted.
Change-Id: I15e33e87e7a7f42d6a06f12fb39b5172153af8a1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4650
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Move towards the removal of the superio model specific xxx_serial_enable
implementation. Make remaining superio romstage parts link-time symbols
and fix corresponding mainboards to match.
The following mainboards remain unconverted as they are ROMCC:
- mainboard/supermicro/x6dai_g
- mainboard/supermicro/x6dhe_g
- mainboard/supermicro/x6dhr_ig
- mainboard/supermicro/x6dhr_ig2
and so block the final removal of w83627hf_serial_enable().
Special cases:
- mainboard/supermicro/h8qme_fam10: Provide local pnp_ sio func
Provide local superio pnp_ programming entry/exit functions as to avoid
making superio implementation global symbols. Although this is not the
proper/final solution, it does mitigate possible symbol collisions and
allow for continued superio refactorisation.
Change-Id: Iaefb25d77512503050cb38313ca90855ebb538ad
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5601
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Part 1/2: These are actually not necessary if Super I/O support is
properly utilized.
Change-Id: I39b621e582f8d0762276d29492c91dce500f0665
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5870
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Bay Trail-I Platform – Bayley Bay-I Customer Reference Board
The Bayley Bay CRB-I is a dual-channel DDR3L SO-DIMM non-ECC platform.
It is designed to support the Bay Trail-I SoC.
This implementation uses the Intel FSP (Vist the Intel FSP
website for details on FSP architecture and support).
This code does not currently support S3. All other features and IO
ports are functional. Booted on Ubuntu 14.04, Mint 16,
Fedora 20 with SeaBIOS payload. Memtest86, FWTS, and
other tests pass.
Notes:
- Generates a 2MB binary to be flashed to the upper 2MB of the ROM,
to preserve the existing Intel Flash Descriptor & TXE binary.
- Tested with B0 & B3 Baytrail I parts
Board support page will be updated on acceptance.
Change-Id: I80c836c7590f2dc25ec854e7a0bb939024cea600
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5792
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Depreciate the model specific early_serial.c romstage component for this
Super I/O in favor of the recent generic winbond romstage framework.
Change-Id: I22775dc9b6341c8994d21591b7176abe4dd99911
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5724
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Depreciate the model specific early_serial.c romstage component for this
Super I/O in favor of the recent generic winbond romstage framework.
Convert dependent board to generic winbond serial init. Note the clock
function is actually invalid since it never enters into PNP config mode
to twiddle the register. Further, 48MHz is the default (page 9 of
data-sheet) and so romstage.c need not do anything to the clock rate
hence why it presumably works with this invalid function.
Change-Id: I4706a1446c1b391b8390ac0361700ce6f15b9206
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5725
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
We now have common ite_*_*() functions for romstage and hence no longer
require the model specific portion of this superio support.
Change-Id: I30400abf27008a88072673075bba445f100d9ad3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5838
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Convert mainboard's that use model specific romstage functions of
it8712f to the generic framework by following the reasoning of:
a7d14a1 ite/common: Introduce common watchdog and 3.3V VSB helpers
Change-Id: I1485306a951103c9a4bc0dbe87c416c91f46c36f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5737
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Removed function only read ACPI MMIO base address from a couple of
registers in IO space.
Change-Id: I25a31b7ac1706b9eebc5db0b9604039928328b0a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5683
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This is x86 "standard" 0xcf9 reset mechanism.
Change-Id: Ieb48290b21a7cb1425881fdd65c794e96da0248f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5680
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These boards return with AGESA_UNSUPPORTED, while other boards return
AGESA_SUCCESS here when there is no hardware for external reset signalling.
Change-Id: I5aed211b1812888af55a691cfbfa8d7b5aff91bc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5679
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Most of the callouts are not specific to board or even family.
Start new file with default callouts doing nothing and returning
either AGESA_SUCCESS or AGESA_UNSUPPORTED.
Also add callout for returning empty IdsIdData. This feature is
not used and could be easily overriden at board-level at later time.
Change-Id: I65dbcdd80dddc89d47669ebe62c22caa63792f5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5678
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I219ae74d60fd7211de2edee96e74bbe13130bb94
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5849
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I31841e7bf578c77d08d452779936fcf5b3026d4f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5848
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: Id967f6057759cf0603c84514d32b067c3658306f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5831
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I4e5f2d7e8e6b76703fccce38fc7e3165d763e97f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5830
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Depreciate the model specific early_serial.c romstage component for this
Super I/O in favor of the recent generic winbond romstage framework.
Change-Id: I529c9cd1d8d63db3035b4828b3c3fc43911f49ce
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5727
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Remove bogus attempt to double program the Super I/O. Remove also a
questionable function that enters Super I/O LDN config space, does no
actual LDN programming, rather multi-function register programming and
then never leaves the config space. Further, we don't export pnp_
symbols from the early_serial.c component into the global namespace.
Change-Id: I7d6b97b174249ae16fe881728da5ca3dd069b696
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5800
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The F2A85-M has IT8603E which is a strip down version of IT8728F.
Change configuration from provisional IT8712F to the IT8728F.
While at it also enable only needed LPC bridge decodes.
As the side effect, this change also implements setup of environmental
controller, thus it87 driver can detect the temperatures/fans.
Change-Id: I22067b13ea27ee37e959a246718d9559c2a3215d
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4499
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I6c5cc46385581d6b69d20f6bc9b016b799765d9e
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5829
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: Idda1a49277c156670014fac27b9f1c378f8df0cd
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5827
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I61fe91e467c29f144323af9c4612420f322098b4
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5826
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I46fad8d236c620ee5dbeb24f4517f20f00db839f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5825
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: If948960abbd927aa6d2b471a42a2321a04d992f3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5824
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in,
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: Idd7305cb34be77894ca4b6062bc0a2dc61126347
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5822
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following the reasoning in:
8089f17 mainboard/lenovo/x230 Fix usage of GNU field designator extension
In C99 we defined a syntax for this. GCC's old syntax was deprecated.
Change-Id: I5be77fe6670601e103260077fae07a5b9fd41f1d
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5821
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
