Issue observed:
Intel raminit works in about 50% of all test-cases on lenovo x220.
Problem solution:
Prefer a smaller valid value over the measured one for
initial timB timings.
Final testing result:
Tests on x220 shows that the issue was resolved.
The test system booted successfully ten times in a row.
Tests on Gigabyte GA-B75M-D3H revealed no regressions.
Test system:
* Intel Pentium CPU G2130
* Gigabyte GA-B75M-D3H
* DIMM: "Crucial 2GB 256Mx64 CT2566aBA160BJ"
Change-Id: I1a115a45d5febf351d89721ece79eaf43f7ee8a0
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11248
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
This patch removes the old arm64/stage_entry.S code that was too
specific to the Tegra SoC boot flow, and replaces it with code that
hides the peculiarities of switching to a different CPU/arch in ramstage
in the Tegra SoC directories.
BRANCH=None
BUG=None
TEST=Built Ryu and Smaug. !!!UNTESTED!!!
Change-Id: Ib3a0448b30ac9c7132581464573efd5e86e03698
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/12078
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch expands the existing ENV_<stage> macros in <rules.h> with a
set of ENV_<arch> macros which can be used to detect which architecture
the current compilation unit is built for. These are more consistent
than compiler-defined macros (like '#ifdef __arm__') and will make it
easier to write small, architecture-dependent differences in common code
(where we currently often use IS_ENABLED(CONFIG_ARCH_...), which is
technically incorrect in a world where every stage can run on a
different architecture, and merely kinda happened to work out for now).
Also remove a vestigal <arch/rules.h> from ARM64 which was no longer
used, and genericise ARM subarchitecture Makefiles a little to make
things like __COREBOOT_ARM_ARCH__ available from all file types
(including .ld).
BUG=None
TEST=Compiled Falco, Blaze, Jerry and Smaug.
Change-Id: Id51aeb290b5c215c653e42a51919d0838e28621f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/12433
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Without BOOTBLOCK_CONSOLE any call to die() fails due to die() symbol
not being defined at link time. die() is not is dependent on the
console backend, and can function without it (the prink gets no-oped).
Change-Id: I6cecafb576c3b1e901f3927c777f6282174fb259
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/12356
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The microcode for Bay Trail that's in the blobs repo is for the
M and D chip variants only. The fsp_baytrail directory is for
Bay Trail I chip variants, and will not boot if the M/D microcode
is used. The microcode for the I variant is supplied as part
of the Bay Trail FSP package.
Change-Id: I5493deb1626dc3cf037053e13e092f5a1143a13a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12334
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The existing arm64 architecture code has been developed for the Tegra132
and Tegra210 SoCs, which only start their ARM64 cores in ramstage. It
interweaves the stage entry point with code that initializes a CPU (and
should not be run again if that CPU already ran a previous stage). It
also still contains some vestiges of SMP/secmon support (such as setting
up stacks in the BSS instead of using the stage-peristent one from
memlayout).
This patch splits those functions apart and makes the code layout
similar to how things work on ARM32. The default stage_entry() symbol is
a no-op wrapper that just calls main() for the current stage, for the
normal case where a stage ran on the same core as the last one. It can
be overridden by SoC code to support special cases like Tegra.
The CPU initialization code is split out into armv8/cpu.S (similar to
what arm_init_caches() does for ARM32) and called by the default
bootblock entry code. SoCs where a CPU starts up in a later stage can
call the same code from a stage_entry() override instead.
The Tegra132 and Tegra210 code is not touched by this patch to make it
easier to review and validate. A follow-up patch will bring those SoCs
in line with the model.
BRANCH=None
BUG=None
TEST=Booted Oak with a single mmu_init()/mmu_enable(). Built Ryu and
Smaug.
Change-Id: I28302a6ace47e8ab7a736e089f64922cef1a2f93
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/12077
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The existing MCT support code did not perform any of the requisite
configuration to support registered or x4 DIMMs. Add the needed
configuration per the BKDG for Family 15h.
Change-Id: I9ee0bb7346aa35f564fe535cdd337ec7f6148f2b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12019
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Sufficient support has been added to allow booting with registered
DIMMs on the KGPE-D16 in certain slots. ECC support needs additional
work; the ECC data lanes appear to cause boot failures in some slots.
Change-Id: Ieaf4cbf351908e5a89760be49a6667dc55dbc575
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12017
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Load microcode to APs when performing baytrail_init_cpus. The updated
fsp1_0 driver calls TempRamInit API with a dummy microcode, so FSP
will not handle the microcode load.
Change-Id: I7b7c0f43da0d149048ae5a8fd547828f42de04fd
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: http://review.coreboot.org/12095
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Load microcode to BSP in bootblock so later on the FSP TempRamInit call
can be success. The updated fsp1_0 driver calls TempRamInit API with a
dummy microcode, so FSP will not handle the microcode load. If BSP is
not loaded a microcode before calling TempRamInit API, the call will
fail with the error No Valid Microcode Was Found.
Change-Id: I1fbe68e14e5a24d8f2da70603cd2f03675b9ca81
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: http://review.coreboot.org/11896
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Pass in dummy microcode when calling FSP TempRamInit API. FSP will not
do the microcode load and leave the work to coreboot.
Ensure that BSP has been loaded a microcode before calling TempRamInit
API, otherwise FSP will return error that No Valid Microcode Was Found.
Change has been verified on fsp_baytrail and will be applied to rangeley.
Change-Id: I8247c0503c8eb3d1c8eaa059632fb3a11c9daae9
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: http://review.coreboot.org/11895
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Load microcode to APs when performing model_406dx_init. The updated
fsp1_0 driver calls TempRamInit API with a dummy microcode, so FSP
will not handle the microcode load.
Change-Id: Ib75f860a34c84bf13c0c6c31ebed13e5787f365e
Signed-off-by: David Guckian <david.guckian@intel.com>
Reviewed-on: http://review.coreboot.org/12436
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Load microcode to BSP in bootblock so later on the FSP TempRamInit call
will return with success. The updated fsp1_0 driver calls TempRamInit
API with dummy microcode, so FSP will not handle the microcode load. If
BSP is not loaded with microcode before calling TempRamInit API, the
call will fail with error No Valid Microcode Was Found.
Change-Id: I9c55acaf3353a759bb0119f0a5402a704ffb2c4a
Signed-off-by: David Guckian <david.guckian@intel.com>
Reviewed-on: http://review.coreboot.org/12367
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: York Yang <york.yang@intel.com>
The current code did not define the number of DIMM slots on the
mainboard, which lead to incorrect configuration values and
occassional training failure.
Add preliminary support for DIMM slot count configuration.
Change-Id: I488511d6262ffa8207c442d133314aed0f75acfb
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12016
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
On some multi-socket AMD platforms there are too many cores for all
APs to start up without stack collisions with either each other or
the BSP. On such platforms a larger amount of CAR memory is also
available.
Allow the maximum DCACHE size to be increased via a mainboard-
specific Kconfig flag.
Change-Id: I72ae8f7abeb9a83b57505469922818f9ec5bdf3f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12015
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
CAR space on certain platforms is nearly full. This prevents the
addition of necessary RAM initialization features such as x4 DIMM
support. As the DIMM SPD cache uses a sizeable amount of CAR RAM,
reducing it would free up a significant amount of CAR RAM.
DDR3-based AMD platforms only support up to 3 physical DIMMs on
each channel (6 per node). Reduce the maximum number of DIMMs
on a node from 8 to 6 accordingly.
Change-Id: I38def86da76fc622785318c825670209b2ac9017
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12107
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On the ASUS KGPE-D16 it was noted that the pin straps did not properly
configure the lane director hardware, causing link training failure
on NIC B. Forcing coreboot to always reconfigure the lane director
on startup resolves this problem.
Change-Id: I5b78cef84960e0f42cc3e0406a7031d12d21f3ad
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12014
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In the course of adding full Family 15h MCT support some Family
15h specific settings were inadvertently applied to Family 10h
processors.
Only apply Family15h specific settings to Family 15h processors.
Change-Id: I5dcb333d3a5a49318fe7bddd4c386642205c343e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12013
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
When both DCTs of a node are in use the DRAM clocks should be skewed
with respect to one another in order to reduce cross-channel interference.
Set the clock skew bit according to the BKDG recommendations.
Change-Id: Ibcce54fc53b79beba2f790994bcf87cc0354213a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12011
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The existing code did not set Rtt timing parameters when registered
DIMMs were used with Family 15h processors. Set the Rtt values
according to the BKDG recommendations.
Change-Id: I80cd7f8aec12951611d802f33e5e167a41dd532e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12010
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
AMD Opteron processors contain a very fragile phy phase detection circuit.
Additionally, the algorithm given in the BKDG does not function as intended;
this was verified both on real hardware via execution trace and on paper
with values read back from multiple CPUs and DIMMs.
As a result, the phy training algorithm given in the BKDG has been
replaced with a phy training algorithm developed at Raptor Engineering.
This particular patch is the first part of that algorithm; the code
is updated in future patches but this should exist in the historical
record in case something breaks down in the later sections of code.
Change-Id: Ic7a19d24954f47c922126e3da7be1f7e85f7396f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12007
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
AMD's automatic phy phase detection hardware is very fragile and often
produces incorrect results. Attempt to recover from obvious phase
locking errors by retrying phy training on the failing link.
Change-Id: Ia2c3022534c9ad44714eef6e118869f054bd9f6b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12006
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The existing MCT code did not properly set up the On Die Termination
(ODT) or timing values for registered DIMMs. Use the BKDG recommended
values when registered DIMMs are installed.
Change-Id: Ia9ee770d9f9c22e18c12e38b5bb4a7bae0a99062
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12005
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
There were numerous issues surrounding AMD ECC initialization on
Family 15h processors due to the incomplete derivation from Family
10h MCT code. Bring the Family 15h ECC initialization and supporting
setup code in line with the BKDG recommendations.
Change-Id: I7f009b655f8500aeb22981f7020f1db74cdd6925
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12003
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The existing ECC initialization algorithm contained several bugs on both
Family 10h and Family 15h processors, including activation of ECC scrub
before DRAM setup was completed, in violation of both BKDG and errata
recommendations.
Change-Id: I09a8ea83024186b7ece7d78a4bef1201ab34ff8a
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12002
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
It's not deprecated if it's still in active use. The code layout is just
"funny" (and could warrant a chipset-side cleanup, but not today)
Change-Id: I5f7776ceba0134f20364a0c4a1ca51382e9877e2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/12429
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since there are no longer any newisys mainboards, remove the directory
and Kconfig files. This removes the Kconfig warning:
mainboard/newisys/Kconfig:3:warning: config symbol defined without type
Change-Id: Icb2e782173166a26fa261f6cfb81b665a846931e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: http://review.coreboot.org/12423
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When using FMAP regions (with option -r) that were generated with a
master header (as done by cbfstool copy, eg. in Chrome OS' build
system), there were differences in interpretation of the master header's
fields.
Normalize for that by not sanity-checking the master header's size field
(there are enough other tests) and by dealing with region offsets
properly.
BUG=chromium:445938
BRANCH=tot
TEST=`cbfstool /build/veyron_minnie/firmware/image.dev.bin print -r
FW_MAIN_A` shows that region's directory (instead of claiming that
there's no CBFS at all, or showing an empty directory).
Change-Id: Ia840c823739d4ca144a7f861573d6d1b4113d799
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0e5364d291f45e4705e83c0331e128e35ab226d3
Original-Change-Id: Ie28edbf55ec56b7c78160000290ef3c57fda0f0e
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/312210
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12416
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is required to handle certain relative-to-flash-start offsets.
BUG=none
BRANCH=tot
TEST=none
Change-Id: I8b30c7b532e330af5db4b8ed65b21774c6cbbd25
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 596ba1aaa62aedb2b214ca55444e3068b9cb1044
Original-Change-Id: Idc9a5279f16951befec4d84aab35117988f7edb7
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/312220
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12415
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Kernel needs to set Audio IRQ as wake capable.
BUG=chrome-os-partner:47450
BRANCH=NONE
TEST=System wakes up from S0ix by pressing headset buttons.
Change-Id: I0f89d05b4c5449e5e3277dde938d941e4ad8cbea
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 65bf434f7c7e1662211f9c8bf61eeb4f41bdc675
Original-Change-Id: I7b5b564023044b4458eb0976488018b3226f4c70
Original-Signed-off-by: Saurabh Satija <saurabh.satija@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311793
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12414
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
during shutdown
DWC2 UDC controller always requires an active packet to be present in
EP0-OUT to ensure proper operation of control plane. Thus, during
shutdown ignore EP0-OUT for queue empty check if only 1 packet is
present.
BUG=b:24676003
BRANCH=None
TEST=Compiles successfully. "fastboot reboot-bootloader" reboots
device without timeout in udc shutdown.
Change-Id: Iafe46c80f58c4cd57f8d58f060d805b603506bbd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4e7c27d849c0411aae58e60a24d8170a27ab8485
Original-Change-Id: Ifa493ce0e41964ee7ca8bb3a1f4bb8726fa11173
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311257
Original-Commit-Ready: Furquan Shaikh <furquan@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/12413
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
In 2014 or so the RTC code was changed to assume the ALTCENTRY
register (0x32) as always being utilized for creating an rtc_time.
However, one needs to ensure it's set at least once otherwise
the year field in rtc_time is not sane.
In practice this doesn't matter unless somone wants to use the
full year value. cmos_init() should do the same thing in the
rtc fail case, but the machine I had never had that set correctly.
BUG=chrome-os-partner:47388
BRANCH=None
TEST=Booted glados w/ 0xff ALTCENTRY value. New value is 0x20.
Change-Id: I028f801c5d717a0018ed00df82c25b466d64670c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7d5be5bc697bef60a264ddc7f67755aa96088d36
Original-Change-Id: I6e12a30c9e08d8c1002e4cef0f143f0f88009e92
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/311264
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/12411
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The elog format stores the year of the event in bcd format.
Semi-recently rtc_get() started returning the full year,
e.g. 2015. However, bin2bcd takes a uint8_t as a parameter.
Converting a full year (2015 or 0x7df) to a uint8_t results
in passing bad values (223 or 0xdf) to bin2bcd. In other words
the input value of bin2bcd needs to be a number between 0 and 99.
Therefore fix that mistake.
BUG=chrome-os-partner:47388
BRANCH=None
TEST=Events show up with correct year in eventlog now.
Change-Id: I9209cb9175c0b4925337e2e5d4fea8316b30022a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 95a86013234dc999c988291f636e2db3803cc24a
Original-Change-Id: I12734bc3a423ba9d739658b8edc402b8d445f22e
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/311263
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/12410
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
1. This is required the BLOB change Ie86bb0cf
AMD Merlin Falcon: Update to CarrizoPI 1.1.0.1 (Binary PI 1.5)
2. This is tested on Bettong Alfa(DDR3) and Beta(DDR4). Both of the
boards can boot to Windows 10. PCIe slots, USB and NIC work.
Change-Id: I6cf3e333899f1eb2c00ca84c96deadeea0e23b07
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/11752
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The SB700 silicon is somewhat buggy; if the links come up in an
incorrect state after POR the silicon cannot automatically recover.
If a disk fails to come online, reset the associated link and try
disk detection again.
Change-Id: I29051af5eca5d31b6aecc261e9a48028380eccb3
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11999
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The existing prefetcher configuration was incorrect; use the correct
values from the AMD Family 10h and Family 15h BKDGs as appropriate.
Change-Id: I287ffa6345e1f4d232d4b2ea4251650ada3fda92
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12417
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The existing code enabled ECC before clearing memory. As the
AMD CPUs will generate MCEs on any invalid check bits, this
resulted in random lockups during memory training due to the
uniniailized check bits.
Initialize ECC check bits before enabling ECC hardware.
Change-Id: I992e7040520570893ba6a213138dd57bfa14733b
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/11996
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Patrick Rudolph