This change allows us to figure out how much of the AP stacks we are
using, as well as to catch any case of an AP overrunning its stack.
Also, the stack is poisoned, which is a good way to catch programming
errors -- code should never count on auto variables being zerod.
The stack bases are recorded in a new array, stacks. At the end,
when all APs are initialized, the stacks are walked and the
lowest level of the stack that is reached is printed.
Build and boot and look for output like this:
CPU1: stack allocated from 00148000 to 00148ff4:\
lowest stack address was 00148c4c
CPU2: stack allocated from 00147000 to 00147ff4:\
lowest stack address was 00147c4c
CPU3: stack allocated from 00146000 to 00146ff4:\
lowest stack address was 00146c4c
Note that we used only about 1K of stack, even though in this
case we allocated 4K (and in the main branch, we allocate 32K!)
Change-Id: I99b7b9086848496feb3ecd207f64203fa69fadf5
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1818
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Right now coreboot's build process produces images that are
not booting on actual hardware because they are smaller than
the actual flash device and also don't have an IFD nor an ME
firmware in them. In order to produce bootable images, you
needed a wrapper script / extra step until now. With this
change, the resulting coreboot.rom is actually bootable.
Change-Id: I82714069fb004d4badc41698747a704bd9fed4da
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1771
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The currently encoded register constraints fails compilation
for SMM code or any code that compiles with -fPIC. The reason
is that the ebx register is used for GOT base register.
I don't believe the comment eluding to register constraints for AMD
processors still applies. Therefore remove mmio_conf.h, and use the
mmio methods in io.h.
Change-Id: I391e5c2088ebc760b3a6ed6c37b65bbecab40a5c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/1801
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Adding more and more optional and non-optional parameters
bloated cbfstool and made the code hard to read with a lot
of parsing in the actual cbfs handling functions. This change
switches over to use getopt style options for everything but
command and cbfs file name.
- This allows us to simplify the coreboot Makefiles a bit
- Also, add guards to include files
- Fix some 80+ character lines
- Add more detailed error reporting
- Free memory we're allocating
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Ia9137942deb8d26bbb30068e6de72466afe9b0a7
Reviewed-on: http://review.coreboot.org/1800
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This removes almost all C++ code (except the wrapper)
Change-Id: I0f84070e3b6dc57c98d49a53150a140479b3221f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1799
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some of the modules use their own rolled pci_or_configX functions.
Therefore, make them first class so everyone can use them without
copying them.
Change-Id: I9a4d3364c832548dbfe18139c27cce2d60c3316d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/1797
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Double equal sign like "test a == b" works. It really does, except NetBSD.
But I haven't found any clue in the manual for the command test about "==".
Change-Id: I37254cfeb688fd1092f2e549d24f8eb270f02fd8
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1817
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The appropriate compiler (provided by the build system) is used to
ensure proper toolchain options are used.
cbmem.c is being modified to suppress pointer to integer typecast
warnings.
Change-Id: Ibab2faacbd7bdfcf617ce9ea4296ebe7d7b64562
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1791
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If cmos is invalid for any reason, always set the date and time
before marking RTC valid.
Change-Id: Ib9d154802f75221d58bf28ba9c813f2529904596
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1790
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove the duplicate #defines and use what is set in mc146818rtc.h.
Change-Id: Ic471e03c68b591d19c0646fdbea78374af11c8b8
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1789
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The MRC cache code, as implemented, in some cases uses configuration
settings for MRC cache region, and in some cases - the values read
from FMAP. These do not necessarily match, the code should use FMAP
across the board.
This change also refactors mrccache.c to limit number of iterations
through the cache area and number of fmap area searches.
Change-Id: Idb9cb70ead4baa3601aa244afc326d5be0d06446
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1788
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Adding an entry for 0x306a0 will make sure that all
CPUs with CPUIDs 0x306aX will execute the driver (analog to
Sandybridge behavior)
Change-Id: I0353f3a48ecfd41274fdf6ee302c7d34482f1b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1783
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
in the resume case, timestamps were collected in RAM stage
but not stored in CBMEM. This leads to only a single time stamp
covering 200ms being available for all of ram stage.
Change-Id: Ibf0bb92caf5e032c12fe4e1b9b84b3624d499511
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1781
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
coreboot uses about 2K of stack on the BSP, and about 1K of stack on the
APs. No reason to use an overdimensonal stack of 32k per core/thread.
Change-Id: I734c240b992d40e1e35db3df5437c36da0a755cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1780
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a basic romstage driver that can be used for the
MRC cache code on systems where we do not have the MRC cache
stored in a flash region that is memory mapped.
It uses the hardware sequencing interface to avoid having
to know anything about the flash chip itself.
BUG=chrome-os-partner:15031
BRANCH=stout
TEST=manual: this was tested with debug code added to romstage
that attempted to read the MRC cache at offset 0x3e0000.
SPI READ offset=003e0000 size=64 buffer=ff7fba00
SPI ADDR 0x003e0000
SPI HSFC 0x3f00
SPI READ: 0=4443524d
SPI READ: 1=00000bb0
SPI READ: 2=00008e24
SPI READ: 3=00000000
SPI READ: 4=001c8bbb
SPI READ: 5=0c206466
SPI READ: 6=0a043220
SPI READ: 7=000058b4
SPI READ: 8=00000000
SPI READ: 9=00000000
SPI READ: 10=00100000
SPI READ: 11=00100005
SPI READ: 12=20202025
SPI READ: 13=000e0001
SPI READ: 14=00000000
SPI READ: 15=00000000
Change-Id: I5f78f53111f912ff5dda52bbf90fdc1824b82681
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1777
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the event log is stored in flash that is not memory
mapped then it must use the SPI controller to read from
the flash device instead of relying on memory accesses.
In addition a new CBMEM ID is added to keep an resident
copy of the ELOG around if needed. The use of CBMEM for
this is guarded by a new CONFIG_ELOG_CBMEM config option.
This CBMEM buffer is created and filled late in the process
when the SMBIOS table is being created because CBMEM is
not functional when ELOG is first initialized.
The downside to using CBMEM is that events added via the
SMI handler at runtime are not reflected in the CBMEM copy
because I don't want to let the SMM handler write to memory
outside the TSEG region.
In reality the only time we add runtime events is at kernel
shutdown so the impact is limited.
Test:
1) Test with CONFIG_ELOG_CBMEM enabled to ensure the event
log is operational and SMBIOS points to address in CBMEM.
The test should involve at least on reboot to ensure that the
kernel is able to write events as well.
> mosys -l smbios info log | grep ^address
address | 0xacedd000
> mosys eventlog list
0 | 2012-10-10 14:02:46 | Log area cleared | 4096
1 | 2012-10-10 14:02:46 | System boot | 478
2 | 2012-10-10 14:02:46 | System Reset
3 | 2012-10-10 14:03:33 | Kernel Event | Clean Shutdown
4 | 2012-10-10 14:03:34 | System boot | 479
5 | 2012-10-10 14:03:34 | System Reset
2) Test with CONFIG_ELOG_CBMEM disabled to ensure the event
log is operational and SMBIOS points to memory mapped flash.
The test should involve at least on reboot to ensure that the
kernel is able to write events as well.
> mosys -l smbios info log | grep ^address
address | 0xffbf0000
> mosys eventlog list
0 | 2012-10-10 14:33:17 | Log area cleared | 4096
1 | 2012-10-10 14:33:18 | System boot | 480
2 | 2012-10-10 14:33:18 | System Reset
3 | 2012-10-10 14:33:35 | Kernel Event | Clean Shutdown
4 | 2012-10-10 14:33:36 | System boot | 481
5 | 2012-10-10 14:33:36 | System Reset
Change-Id: I87755d5291ce209c1e647792227c433dc966615d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1776
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Fix handling of 5-byte Fast Read command in the ICH SPI
driver. This fix is ported from the U-boot driver.
- Allow CONFIG_SPI_FLASH_NO_FAST_READ to be overridden by
defining a name for the bool in Kconfig and removing the
forced select in southbridge config
- Fix use of CONFIG_SPI_FLASH_NO_FAST_READ in SPI drivers
to use #if instead of #ifdef
- Relocate flash functions in SMM so they are usable.
This really only needs to happen for read function pointer
since it uses a global function rather than a static one from
the chip, but it is good to ensure the rest are set up
correctly as well.
Change-Id: Ic1bb0764cb111f96dd8a389d83b39fe8f5e72fbd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1775
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Applied function attribute to function definition to avoid 'conflicting type' warning.
Function declaration is in src/include/cpu.h
void secondary_cpu_init(unsigned int cpu_index)__attribute__((regparm(0)));
But function definition in lapic_cpu_init.c is missing the "__attribute__" part.
Change-Id: Idb7cd00fda5a2d486893f9866920929c685d266e
Signed-off-by: Han Shen <shenhan@google.com>
Reviewed-on: http://review.coreboot.org/1784
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The Intel PCH can override the ASPM settings via the MPC2 register.
Add a chip override for F0-F7. Mainboards may implement this as
needed.
This also fixes the final PM setup being done too early. It was
being done prior to the PCIe ASPM setup, which happens in the
bridge scan.
Change-Id: Idf2d2374899873fc6b1a2b00abdb683ea9f5bd6b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1796
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Right now the SPI bus is getting set to 20mhz for transactions
initiated with the software sequence interface.
In order to be able to do reasonable fastread/write/erase we
can bump this up to a higher value at boot before it gets
locked at 20mhz.
To do this read out the speed set in the SPI descriptor for
hardware sequencing and apply it to software sequencing.
Change-Id: I79aa2fe7f30f734785d61955ed81329fc654f4a4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1773
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The chips we are using do not use BE52 (block erase 0x52)
so we can use that opcode menu location to enable fast read.
Change-Id: I18f3e0e5e462b052358654faa0c82103b23a9f61
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At least when CONFIG_CHROMEOS is turned on, it's possible for
CONFIG_FRAMEBUFFER_KEEP_VESA_MODE to be set but for there not to be any valid
information to put into the framebuffer coreboot table. That means that what's
put in there is junk, probably all zeroes from the uninitialized global
variable the mode information is stored in (mode_info).
When a payload uses libpayload and turns on the coreboot framebuffer console,
that console will attempt to scroll at some point and decrease the cursor's y
coordinate until it is less than the number of rows claimed by the console.
The number of rows is computed by taking the vertical resolution of the
framebuffer and dividing it by the height of the font. Because the mode
information was all zeroes, the coreboot table info is all zeroes, and that
means that the number of rows the console claims is zero. You can't get the
unsigned y coordinate of the cursor to be less than zero, so libpayload gets
stuck in an infinite loop.
The solution this change implements is to add a new function,
vbe_mode_info_valid, which simply returns whether or not mode_info has anything
in it. If not, the framebuffer coreboot table is not created, and libpayload
doesn't get stuck.
Change-Id: I08f3ec628e4453f0cfe9e15c4d8dfd40327f91c9
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1758
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
And move the pre-hardwaremain post code to 0x79
so it comes before hardwaremain at 0x80.
Emit these codes from ACPI OS resume vector as well
as the finalize step in bd82x6x southbridge.
Change-Id: I7f258998a2f6549016e99b67bc21f7c59d2bcf9e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1702
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Coreboot and u-boot create a table of timestamps which allows to see
the boot process performance. The util/cbmem/cbmem.py script allows to
access the table after ChromeOS boots up and display its contents on
the console. The problem is that shipping images do not include Python
interpreter, so there is no way to access the table on a production
machine.
This change introduces a utility which is a Linux app displaying the
timestamp table. Conceivably the output of this utility might be
included in one of the ChromeOS :/system sections, so it was attempted
to write this procedure 'fail safe', namely reporting errors and not
continuing processing if something goes wrong.
Including of coreboot/src .h files will allow to keep the firmware
timestamp implementation and this utility in sync in the future.
Test:
. build the utility (run 'make' while in chroot in util/cbmem)
. copy `cbmem' and 'cbmem.py' to the target
. run both utilities (limiting cbmem.py output to 25 lines or so)
. observe that the generated tables are identical (modulo rounding
up of int division, resulting in 1 ns discrepancies in some
cases)
localhost var # ./cbmem
18 entries total:
1:62,080
2:64,569 (2,489)
3:82,520 (17,951)
4:82,695 (174)
8:84,384 (1,688)
9:131,731 (47,347)
10:131,821 (89)
30:131,849 (27)
40:132,618 (769)
50:134,594 (1,975)
60:134,729 (134)
70:363,440 (228,710)
75:363,453 (13)
80:368,165 (4,711)
90:370,018 (1,852)
99:488,217 (118,199)
1000:491,324 (3,107)
1100:760,475 (269,150)
localhost var # ./cbmem.py | head -25
time base 4249800, total entries 18
1:62,080
2:64,569 (2,489)
3:82,520 (17,951)
4:82,695 (174)
8:84,384 (1,688)
9:131,731 (47,347)
10:131,821 (89)
30:131,849 (27)
40:132,618 (769)
50:134,594 (1,975)
60:134,729 (134)
70:363,440 (228,710)
75:363,453 (13)
80:368,165 (4,711)
90:370,018 (1,852)
99:488,217 (118,199)
1000:491,324 (3,107)
1100:760,475 (269,150)
Change-Id: I013e594d4afe323106d88e7938dd40b17760621c
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1759
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The sleep type is 5 for S3 and 7 for S5.
Change-Id: I7ffdb3d27b6994ac4a12a343caf4d7abb82fe6ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If these values are non-zero then the kernel will issue
an SMI for each core (cstate) and package (pstate).
Since we don't do anything with these SMI callbacks we
can avoid taking the extra SMIs at boot time by zeroing
these fields.
Change-Id: I3bc5fe0a9f45141d46884cb77ecdfaeaa45d2439
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1769
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The VMX MSR may come up with random values and needs to be
initialized to zero. This was done incorrectly in finalize_smm.
It must be done on a per core basis in the general CPU init.
This touches all Sandybridge and Ivybridge configs.
Change-Id: I015352d0f8e2ebe55ac0a5e9c5bbff83bd2ff86b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1794
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The MSR for VMX can start with a random value and needs to be
cleared by coreboot. I am reverting this change, as
it handles almost everything and doing a follow-on change to fix
the improper clearing of the MSR.
Change-Id: Ibad7a27b03f199241c52c1ebdd2b6d4e81a18a4e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1793
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The reporting of cores and threads in the system was a bit
ambiguous. This patch makes it clearer.
Change-Id: Ia05838a53f696fbaf78a1762fc6f4bf348d4ff0e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1786
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Example:
cbfstool image-link.bin add-flat-binary u-boot.bin fallback/payload \
0x100000 0x100020
will add u-boot.bin as fallback/payload with a load address of 0x100000
and an entry-point of 0x10002.
Change-Id: I6cd04a65eee9f66162f822e168b0e96dbf75a2a7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1792
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
A payload may want to decide whether it uses certain input/output consoles,
or that it wants support for outputing to a particular device but not to use
that device as a console. This change adds a config option which skips the
call to console_init in start_main.
Change-Id: I32b224d4d0bd3a239b402ecb09ee907d53225735
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1732
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This makes their names more consistent with other constants in this header,
avoids name collisions, and makes it more obvious where the names came from.
Change-Id: I7b8bd4ada0fbaf049f35759a907281265f5bb2e6
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1729
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Some constants which were used to interpret the contents of the coreboot
tables were moved to the appropriate libpayload header file. The constant which
describes the maximum length of a GPIO name was renamed to have a CB_ prefix.
That makes it more obvious what sort of GPIO name it describes, and reduces the
change of a name collision. It also makes it more consistent with other names
in that header, although some other exceptions still exist.
Change-Id: I6c0082b3198d34e8a78507fbfac343ee8facf0dc
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1728
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Added ehci_reset() function to do a full reset of
the host controller
Change-Id: Ia48db8462ebbb8f260813eb6ba8349d002c4678b
Signed-off-by: Anton Kochkov <a.kochkov@securitycode.ru>
Reviewed-on: http://review.coreboot.org/1814
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On Sandybridge and Ivybridge systems the firmware image has to
store a lot more than just coreboot, including:
- a firmware descriptor
- Intel Management Engine firmware
- MRC cache information
This option allows to limit the size of the CBFS portion in
the firmware image.
Change-Id: Ib87fd16fff2a6811cf898d611c966b90c939c50f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1770
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
src/include/timestamp.h is an interface describing timestamp storage
in coreboot. Exporting this interface is complicated by inclusion of
tsc.h which is needed only for the API and is not used in structure
definitions. Including this dependency only when needed fixes the
problem.
Change-Id: Ie6b1460b1dab0f5b5781cb5a9fa89a1a52aa9f17
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1753
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
These bits are used by the IGD OpRegion code
Change-Id: I89a11fc5021d51e0c1675ba56f6a3bc3b79bb8aa
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1751
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
In order to support Intel's IGD Opregion standard, we need
an additional set of flags shared between firmware, ACPI, SMM, and the
graphics driver.
Change-Id: I1a9b8dff5e5ee8d501b6672bc3bcca39ea65572e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These can be stored in the code segment, since it's never changed.
Change-Id: I8b3827838e08e6cc30678aad36c39249fbca0c38
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1749
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add support for GigaDevice SPI ROMS.
The GD25Q64B device has been tested, the other rom devices added to the
file have not.
Change-Id: If35676ca6b90329f15667ebb32efa0d1a159ae91
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1747
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These events were initially for Chrome EC but they can be
applied to any EC.
Change-Id: I0eba9dbe8bde506e7f9ce18c7793399d40e6ab3b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the driver is initialized before the lockdown then it will
fail to work after the lockdown bit is set.
Change-Id: Idc05d33d8d726bf29cb3c9b1b4604522bd64170a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Ronald G. Minnich