In TGL SoC we have PCH and CPU side PCIe support. This patch
skips CPU side PCIe enablement in FSP if device is disabled in
devicetree. Disabling the initialization of CPU PCIe saves ~30ms
in FspSiliconInit!
BUG=b:158573805
BRANCH=None
TEST=Build and boot volteer and TGL RVP. Using cbmem tool measure the
boot time. FspSilicontInit time is reduced by ~30ms with this patch.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I7e8512d22b1463bc4207f80b16dcfb5d00ef4b46
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42557
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enabling VT-d on pre-QS silicon may have issues like rendering the
Thunderbolt driver useless. This change will ensure that VT-d is
disabled for pre-QS silicon and enabled for QS.
BUG=b:152242800,161215918,158519322
TEST=Validated VT-d is disabled for pre-QS (cpu:0x806c0) and enabled for
QS (cpu:0x806c1). Kernel walks through ACPI tables. If VT-d is disabled
and no DMAR table exists, IOMMU will not be enabled.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I98a9f6df185002a4e68eaa910f867acd0b96ec2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The following changes are done in this patch:
1. Get the CSE partition info containing version of CSE RW using
GET_BOOT_PARTITION_INFO HECI command
2. Get the me_rw.version from the currently selected RW slot.
3. If the versions from the above 2 locations don't match start the update
- If CSE's current boot partition is not RO, then
* Set the CSE's next boot partition to RO using SET_BOOT_PARTITION
HECI command.
* Send global reset command to reset the system.
- Enable HMRFPO (Host ME Region Flash Protection Override) operation
mode using HMRFPO_ENABLE HECI command
- Erase and Copy the CBFS CSE RW to CSE RW partition
- Set the CSE's next boot partition to RW using
SET_BOOT_PARTITION HECI command
- Trigger global reset
- The system should boot with the updated CSE RW partition.
TEST=Verified basic update flows on hatch and helios.
BUG=b:111330995
Change-Id: I12f6bba3324069d65edabaccd234006b0840e700
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The prompts for the DPTF Kconfig options were not necessary, they should
be selected based on what DPTF implementation is being used, ASL files
or generated at runtime. It's not really meant to be fiddled with at
build-time. Also rewrite the help text for the _HID selection, to try
and make it more clear when to use y or n.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6edcabd28426916d9586d501b95b510dfc163fc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43830
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This macro is not correct because the RX Level/Edge Configuration
(trig) and the GPIO Tx/Rx Buffer Disable (bufdis) fields in DW0
register do not affect on the pad in the native function mode.
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: Ic0416e3f67016c648f0886df73f585e8a08d4e92
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Michael Niewöhner
According to the documentation [1], RX Level/Edge Configuration (trig)
and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable
in native mode and BIOS does not need to configure them. Therefore,
there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG
macros. Use PAD_CFG_NF instead and set this fields to 0.
[1] Intel document #549921
[2] Intel document #336067-007US
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: I6a6b745bdaacb1c4fbf032e4ce54cb25a72d790a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43561
Reviewed-by: Michael Niewöhner
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the documentation [1], RX Level/Edge Configuration (trig)
and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable
in native mode and BIOS does not need to configure them. Therefore,
there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG
macros. Use PAD_CFG_NF instead and set these fields to 0.
[1] Intel document #549921
[2] Intel document #336067-007US
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: Icdb6cb39934548e125461929701b33477a74f2a2
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43454
Reviewed-by: Michael Niewöhner
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This effectively reverts commit 5086ccef
(mb/purism/librem_skl: Fix CLKREQ for 15v3 NVMe).
Some Librem 15v3/v4 boards are showing issues with NVMe detection or
booting via SeaBIOS, so revert this until a proper fix can be found.
Test: build / successfully boot Librem 15v4 with problematic NVMe drive.
Change-Id: I0659f77bbe693f3d3b192a28ff3ef013658930cc
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43490
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For devices sharing same firmware, there may be few customization based
on SKU ID - for example being clamshell or form factor. On Kukui and
Jacuzzi platforms the SKU ID is defined on AP SOC, so we have to send
the information to EC.
BUG=b:161767717
TEST=make -j # builds and boots on Juniper
BRANCH=kukui
Change-Id: I8ffdd9fd1e609c1dd4b0e22dc7aab560ccdc842e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43788
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, audio is not working on Boten, caused by the coreboot
HDA driver not being run as the Jasper Lake PCI ID is missing.
So, add the Jasper Lake ID.
BUG=b:160651126
BRANCH=NONE
TEST=Connect speaker to audio jack, and verify sound is played.
Signed-off-by: Yan Liu <yan.liu@bitland.corp-partner.google.com>
Change-Id: Ib62c332d8d87201b3e6903251d824e1c3e06cd68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43441
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Peichao Li <peichao.wang@bitland.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
HDMI DDC GPIOs were configured as NC till now in waddledoo.
This may cause HDMI i2c transfer to break and EDID read will
fail due to wrong configuration
Configuring these GPIOs as NF in coreboot to fix the issue.
BUG=b:160324327
BRANCH=None
TEST=HDMI works on DDI2 onn Type-C port
Change-Id: If02f062132d7c3b01b07ea9401e81f451df35c3c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43294
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune I2C bus3 frequency and insure it meets I2C spec.
BUG=b:161650117
TEST=flash coreboot to the DUT and actual measured I2C bus3
make sure it meet Spec.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Ifa9f0bce723f55a12fd2313788c995f8326e3e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix the scan-build warning below:
CC romstage/drivers/mrc_cache/mrc_cache.o
src/drivers/mrc_cache/mrc_cache.c:450:26: warning: Value stored to 'flash' during its initialization is never read
const struct spi_flash *flash = boot_device_spi_flash();
^~~~~ ~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
The function can return early before the value is read. Fix this, by
getting rid of the variable, as the value is only read once.
Change-Id: I3c94b123f4994eed9d7568b63971fd5b1d94bc09
Found-by: scan-build (clang-tools-9 1:9.0.1-12)
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Rename the pch_init function to bootblock_pch_init and romstage_pch_init
according to the stage it is defined in.
TEST=Able to build and boot Waddledoo successfully.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: Iaa0a41f3b5972251d6cd9359bbb46d392196b2e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The outb() call is replaced with the post_code()
The post_codes.h is replaced with console.h since console.h
includes both the post_code definition and post_codes.h
Change-Id: I21345260e86de30614c416e2f509bd77b9e00cb7
Signed-off-by: Sindhoor Tilak <sindhoor@sin9yt.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
BOOL type Kconfig values should be used through the CONFIG() macro.
These instances were not, so update them.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ie4706d82c12c487607bbf5ad8059922e0e586858
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Kconfig lint tool checks for cases of the code using BOOL type
Kconfig options directly instead of with CONFIG() and will print out
warnings about it. It gets confused by these references in comments
and strings. To fix it so that it can find the real issues, just
update these as we would with real issues.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We have definitions for the bits in the PCI COMMAND register. Use them.
Also add spaces around bitwise operators, to comply with the code style.
Change-Id: Icc9c06597b340fc63fa583dd935e42e61ad9fbe5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Mark the CPU as enabled and the socket as populated.
EDK2 tests these flags before further reading this structure.
Change-Id: Ic545bb47c502cb9d2352ba6d43eaed8c97229c02
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43703
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement type 19 by accumulating the DRAM dimm size found in cbmem's
CBMEM_ID_MEMINFO structure. This seems common on x86 where the
address space always starts at 0.
At least EDK2 uses this table in the UI and shows 0 MB DRAM if not
present.
Change-Id: Idee8b8cd0b155e14d62d4c12893ff01878ef3f1c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Don't initialize fields with zeroes since gnvs structs were zeroed out
in southbridge already. Also add some comments.
See also these commits:
* Commit a76cf28 with Change-Id
I2ccf4699ba3ed3f5b9402c0340153d4a5bf82682 ("mb/lenovo/*/acpi_tables:
Don't initialize already initialized fields").
* Commit 0c52638 with Change-Id
I71f092ed7582b4931122d72f41d0b42a7569b96e ("mb/lenovo: Remove
thermal.h header").
Change-Id: I1a0042bc93a2b30babcb896b3df23faf37998f3c
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40479
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Update MAINBOARD_PART_NUMBER for TGL variants
- MAINBOARD_PART_NUMBER is reported as FRID on acpi
- This is required for cros_config to differentiate
across TGL variants.
- Mosys uses cros_config to identify TGL variants using
data read from FRID
Bug=none
Test=build and boot coreboot on TGLRVP UP3 hardware
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I11d4ab2a5b6ade6c50988a9fec4d9866fe79d7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Set up a 8-byte I/O range at 0x290-0x297 as PIIX4's generic device 9,
which activates a chip select when this range is accessed.
On the P2B family it connects to the W83781D hardware monitor,
allowing access to it over the ISA bus, just like vendor firmware.
Apparently this does not work on p3b-f, but no ill effects observed
either.
TEST=On p2b-ls lm-sensors can detect chip and get readings over ISA.
Change-Id: Iaed1df7230359e94c580c305f4769c8bb4f5fce0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These will be put to use in a follow-up.
Change-Id: Id13dde5ce2239064b9b18de7ca516525158ae268
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Remove EIO define. It is unused and means something else,
elsewhere in the tree.
Move PMIOSE bit definition next to PMREGMISC, where it actually
belongs.
Correct a number of bit defines with glaring errors.
Clarify in comments which PM register defines are in PCI config
space are which are in I/O space.
Change-Id: Ic7f2267d013403c0a519c2ee1786bd3c7f5a9708
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Embedded Firmware Structure contains various SPI parameters for
the PSP to program. This change adds support to amdfwtool for
populating these values as well specifying SOC Family and Model.
BUG=b:158755102
TEST=Read EFS values at appropriate offsets using a hex editor. Boot
test on Tremblye and Morphius.
Change-Id: I87c4d44183ca65a5570de5e0c7f9b44aa6dd82f9
Signed-off-by: Matt Papageorge <matt.papageorge@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42566
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Shaunak Saha