Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug.
Change-Id: I2dae22c0db294f5334d9796d90f432d6c8d304df
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: I5b99a66fb64683f3647ebff3ab01ceb52058f79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The code for setting the LPC generic memory range uses an array of fixed
address ranges not needing explicit decoding, to decide if the address
needs to be written to the LGMR register. Most platforms only mistakenly
add the PCH reserved mmio range, that is not decoded generally,
effectively breaking the mechanism. Only APL uses the array correctly.
That code, in it's current state, does not work (except for APL) and
currently, there is not a single user. Thus, drop it before people start
using it.
Change-Id: I723415fedd1b1d95c502badf7b0510a1338b11ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I795b8da3c5e1efb51c8fe4673f025839a1c630bc
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I2f484d232a46214ff98168f41f96d56b047892e2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I67bdd9a96928b77a9a178afea7dab03dc370312c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Do early pad configuration in early bootblock before console init, to
make the console work as early as possible. The board does not do any
other gpio configuration in bootblock, so this should not influence
behaviour in a negative way (e.g. breaking overrides).
Change-Id: I342b9217af0288a3b525e629aac791eb0f880442
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
We need to write some special values to key protection registers before
applying init_setting table and lp_setting table to PMIC. Otherwise,
those settings won't take effect.
After applying init_setting table and lp_setting table, we lock the
settings by writing zero to key protection registers.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I593d4e02bf0b62ac297957caf4ae1c1837f1f38d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Functionality depends of CMAP and CMBP references inside board
specific ASL implementation. Only roda/rk9 and roda/rk886ex has
that.
Change-Id: I4da8292375cb589d67dc68496b1e81971bc2a61f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49274
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APIC was not referenced anywhere in ASL.
MPEN has references under boards:
getac/p470, roda/rk9, roda/rk886ex.
MPEN has reference also in Intel SpeedStep ASL.
Replace static MPEN with detection of multiple CPUs
installed.
Change-Id: Ib5f06416b23196b7227ccd5814162925c31c084b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Only amd/picasso and amd/stoneyridge have reference to
PCNT and that could be replaced with acpigen.
Remove the PCNT name from GNVS OperationRegion elsewhere.
Change-Id: I7dd45a840b3585fd24c31fd923b991c34ab4d783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The BACKLIGHT_ENABLE pin on this board unfortunately defaults to a
pull-up on power on, meaning the backlight is immediately enabled. Best
we can do about that is to turn it off again early and wait until it is
actually correct in the panel power sequence to turn it back on.
Some panels want an explicit 80ms delay after training the eDP
connection before the backlight is turned on (this is probably just to
avoid temporary display artifacts, but whatever). We don't want to
busy-wait that extra time, so instead just delegate turning on that GPIO
to the payload (which is also in charge of the backlight PWM already).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id8dafbdcb40175fbc9205276eee698583b971873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000.
Change-Id: Ia6c2ee29e37040ea9b11505e9888c7f6f8da78bc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This memory is used for option roms and BIOS. This matches the ACPI
code.
Change-Id: I53dd4b967569889108352ca70086a12ce252e8e0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: I626989fa6625e0b3613a11e709c614d40a788b0e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This pulls in the following changes:
* Drop geode_lx
* cpu/amd/model_fxx: Drop unused microcode
* cpu/amd/model_10xx: Drop unused microcode
* soc/mediatek/mt8192: Add dram.elf for DRAM full calibration
* soc/mediatek/mt8192: Add dpm binary
* soc/mediatek/mt8192: Add 4266Mbps flag for dpm & dram blob
* soc/mediatek/mt8192: add SPM firmware
* soc/mediatek/mt8192: Support 26M clock off in SPM
* soc/mediatek/mt8192: Add SSPM firmware
* soc/mediatek/mt8192: Add MCUPM firmware
* soc/mediatek/mt8192: Update MCUPM firmware
* soc/mediatek/mt8192: Support discrete DRAM modules
* mb/amd/majolica: Add APCB configuration files
Change-Id: I5c18349307421707fac71f392b785f3e2bef3acb
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: If4e05f496abc05e06a944b244824376f3937a57b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Chrome EC dropped strago support, so we need to disable it here
before updating our Chrome EC submodule.
Change-Id: Ied8905e995fd040b981ce18e95e225ade496d23c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48216
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Struct will be synced with picasso with followups.
Change-Id: I5f460cc3849bf1fad1f6da61169893488ccb2b40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48855
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to use the function smbios_mainboard_version()
to query the board revision from the EC.
we need to select GOOGLE_SMBIOS_MAINBOARD_VERSION.
BUG=b:177818769
TEST=1. emerge-volteer coreboot chromeos-bootimage
2. flash the image to the device and check board rev
by using command `dmidecode -t 1 | grep Version`
Change-Id: I2474ee03845356d0775f6da25274f696ad33f935
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SoC code has in implicit dependency on this option, so select it in
the SoC code instead of the mainboard code.
Change-Id: Iea908c142f4a94a107cf74a31d9f5e29668d4b5b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Create the sasukette variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:175848514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKETTE
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I0a554efe0919dc2f5880f0f7817a37bd4be88ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change enables LTE modem for sasuke.
- Add LTE modem device into devicetree
- Add GPIO control for LTE modem power on and off
BUG=177177967
TEST=Built and verified modem device existence with lsusb
Change-Id: I34ba8ab00b73f24d1786ab014e9981b172a63a27
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49163
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Writing 0 to MSR IA32_BIOS_SIGN_ID before fetching this MSRs content
is required. This is how things are done in
cpu/intel/microcode/microcode.c.
The "Intel® 64 and IA-32 Architectures Software Developer’s Manual"
also recommends this: "It is recommended that this field be preloaded
with 0 prior to executing CPUID" (this field being %edx).
Change-Id: I24a87aff9a699ed8ab2598007c8b8562d0555ac5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
DPTF paramerters from thermal team.
1. PL1 max =5.8W
2. PL1 min =3.8W
3. PL2 =20W
BUG=b:177249297
BRANCH=dedede
TEST=build image and verified by thermal team.
Change-Id: I19654b65613817ebecf979ce7ac4f76d370ebdc2
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
- Return the busno based on the stack number.
- Replace pci_mmio_read_config32 with pci_io_read_config32 to get the
register value before mapping the MMIOCFG space.
- Remove the plural `s` as the function now provides one bus number.
Change-Id: I6e78e31b8ab89b1bdcfdeffae2e193e698385186
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Update SMBIOS type 17 type detail. Define this field by module type.
Tested=Execute "dmidecode -t 17" to check type detail is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I6700056edad5db2b86f6da526329b1343b026385
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested=On OCP Delta Lake, verify the VPD values can be read
correctly.
Change-Id: I1c27cb61cd52902c92b3733e53bc8e6fd6a5fe7f
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Given the lack of documentation for this platform, having this info
in coreboot logs (e.g. from board_status) can be pretty useful.
Change-Id: I6a743c1efc1b6da71589460a69bfe4785e3e77a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Dalboz variants do not use an MST hub; remove the i2c tunnel for it.
That bus is actually connected to the battery on these devices, which
should not be exposed to the AP.
BUG=b:175658311
TEST=builds
BRANCH=zork
Change-Id: If1714a5c441bf185efd2517c7c94e57b5f351f5a
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49628
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Felix Held