Add support for AP initiated mode entry. The code flow has been
optimized as below -
Code flow when AP initiated mode entry is disabled:
+-------+
| Start |
+---+---+
|
|
+---------+---------+
|wait_for_connection|
| Is DP ALT mode |
| available? |
+---------+---------+
|
+--------------->-------+
Yes| No |
+---------+---------+ |
|Skip enter_dp_mode | |
+---------+---------+ |
| |
| |
+-----------+----------+ |
|wait_for_dp_mode_entry| |
| Is DP flag set? | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| wait_for_hpd | |
| Is HPD_LVL flag set? | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| Rest of the code | |
+-----------+----------+ |
| |
+---------------<-------+
|
+---+---+
| End |
+-------+
Code flow when AP initiated mode entry is enabled:
+-------+
| Start |
+---+---+
|
+------------+-----------+
|Skip wait_for_connection|
+------------+-----------+
|
+--------+-------+
| enter_dp_mode |
| Is USB device? |
+--------+-------+
|
+--------------->-------+
Yes| No |
+---------+---------+ |
| enter_dp_mode | |
| Send DP mode | |
| entry command | |
+---------+---------+ |
| |
+-----------+----------+ |
|wait_for_dp_mode_entry| |
| Is DP flag set? | |
| (If not, loop wait | |
| until timed out) | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| wait_for_hpd | |
| Is HPD_LVL flag set? | |
| (If not, loop wait | |
| until timed out) | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| Rest of the code | |
+-----------+----------+ |
| |
+---------------<-------+
|
+---+---+
| End |
+-------+
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Time taken by enter_dp_mode / wait_for_dp+hpd / MultiPhaseSiInit
functions with this patch train:
1. When AP Mode entry is enabled
- With type-c display on C1 and SuzyQ on C0: 6.9ms / 420ms / 616ms
- With USB key on C1 and SuzyQ on C0 : 6.0ms / 505ms / 666ms
- Without any device on C1 and SuzyQ on C0 : 3.7ms / 0ms / 178ms
2. When AP Mode entry is disabled
- With type-c display on C1 and SuzyQ on C0: 1.7ms / 2.5ms / 213ms
- With USB key on C1 and SuzyQ on C0 : 0.9ms / 3.3ms / 177ms
- Without any device on C1 and SuzyQ on C0 : 0.8ms / 1.8ms / 165ms
Without this patch train, wait_for_hpd would cause a constant delay of
WAIT_FOR_HPD_TIMEOUT_MS (i.e. 3 seconds) per type-c port when there is
no device connected.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I514ccbdbaf905c49585dc00746d047554d7c7a58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Split wait-loop for DP and HPD flags as below -
- google_chromeec_wait_for_hpd
- google_chromeec_wait_for_dp_mode_entry
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3e565d6134f6433930916071e94d56d92dc6cb06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76370
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Wait for DP/HPD flags only in AP initiated mode entry
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I5137c346fbf1edabc60a53e0978e32f54885c330
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76369
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Skip TCSS `wait_for_connection` for AP initiated mode entry.
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ia04ff470961831237fe851f7ae3feaa5623d4b4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76368
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Skip TCSS `enter_dp_mode` command when there is no USB device detected
on the port.
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ie6cd84cab3631596d4d7178dae2040e25c621f63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
The PRESERVE flag in the FMD file tells futility not to erase the
fmap partition when updating the firmware. Because of an issue on
myst right now, we want the RW_MRC_CACHE partition to be erased
when the firmware is updated.
BUG=b:290763369
TEST=None
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id586ae057b2fd6d513ddbba5e1284dea39467d95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76478
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Phoenix doesn't have an eMMC controller and those UPDs were carried over
from Picasso. The SoC's fsp_m_params.c didn't write to any of those
fields, so this doesn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie3640c1493a92c1effba3ce42103d022bd8399ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Because of the way that the CBFS filename is generated from the contents
of the microcode patch, if a duplicate microcode patch is included in
the build, the makefile would create a second copy of the name, which
doesn't work. This led to "odd" results where the other attributes of
the first copy were erased, causing cbfstool to fail. The cause of the
failure is not immediately obvious, and is a little difficult to track
down.
This patch causes an immediate failure and gives a reason as to the
cause of the issue.
When a failure is seen, this is the result:
File1: 3rdparty/amd_blobs/phoenix/psp/TypeId0x66_UcodePatch_PHXn4_A0.bin
File2: 3rdparty/amd_blobs/phoenix/psp/TypeId0x66_UcodePatch_PHX4_A0.bin
src/soc/amd/common/block/cpu/Makefile.inc:25: *** Error: The cbfs
filename "cpu_microcode_a740.bin" is used for both above files. Check
your microcode patches for duplicates.. Stop.
TEST=Now checked for both positive and negative failures.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I3d34dc5585182545bdcbfa6370ebc34aa767cae2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76423
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
System76 boards use the VBT data file, not the VGA optionrom.
Change-Id: Ie4100e09221ae4f301a621e7aac62e38ac04a444
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
There is a data abort in ABL when the memory training data is used from
APOB Cache. Disable APOB Cache until the cause is identified. The
downside of this change is that the memory training happens in every
boot cycle.
BUG=b:290763369
TEST=Build BIOS image and boot to OS in Myst. Trigger a reboot from AP
console and ensure that the system boots to OS.
Change-Id: I20f4f40cdaac68bca6e121e3a238d13fe80d0d3c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
The dxio_port_param_type enum was copied over from Cezanne, but the enum
on the AGESA/FSP side changed between the generations. Add a TODO as a
reminder that this needs to be updated.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8063ab00a508b045265bab73197c8ca117622800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76448
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the proper dxio_link_hotplug_type enum values for the link_hotplug
field in the DXIO descriptors to replace the magic values in the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb1513737e6022a668287dc80a39d96cda2b18d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76439
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the dxio_link_hotplug_type enum definition for the link_hotplug
field in the DXIO descriptor struct.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieeb3e3edaed2c689707edc4df7d25c777005fde2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The dxio_port_param_type enum was copied over from Cezanne to Mendocino
to Phoenix, but the enum on the AGESA/FSP side changed between the
generations. Update the definition to match the definition used in the
Phoenix FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3c87fdc8bf0849d797c2af74c1d1495c7d85019f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76447
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dxio_port_param_type enum was copied over from Cezanne to Mendocino,
but the enum on the AGESA/FSP side changed between the two generations.
Update the definition to match the definition used in the Mendocino FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c4d7e4e3eaf7af9a43007363135412633c7440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76446
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Use newer functions and avoid the * / KiB dance
- Use existing functions for figuring out TSEG and UMA
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic6f42053b5303151906360d8512b9d63dd297854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76249
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The OxPCIe952 serial cards currently fails after entering
postcar, since the state of oxpcie_present is not maintained
from previous stage.
As a quick work-around test the expected UART register space
to see if anyone decodes the address.
Change-Id: I5601034be6e413616fb3433c894fb008a3e02138
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74597
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change `CBFS_SIZE` to match the actual BIOS region size, as specified in
the FIT XML config.
Fixes building with `VALIDATE_INTEL_DESCRIPTOR` selected.
Change-Id: I91a46b3ed6cc3161df27eed19d8cdf2820e90d7e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76326
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It moves cr50_plat_irq_status() to common code and adds Kconfig
option to specify GPIO used for interrupt.
BUG=b:277787305
TEST=Build all affected platform and confirm using right GPIO
number. Tested on Skyrim.
Change-Id: I775c4e24cffee99b6ac3e05b58a75425029a86c8
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75621
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
The file for Mendocino and Phoenix still used Cezanne in the comment and
from the file it's already clear to which SoC generation this belongs,
so just drop the SoC name from the comment.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I73e8b01e46904578226bb64e5e4659016c491880
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76440
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
coreboot logs the error below, since the value of hporch is too small. Increasing hbl from 80 to 174, and hso from 40 to 72 to revise the HBP(Horizontal Back Porch) and HFP(Horizontal Front Porch). After revising this, the actual measurement frame rate is 60.1Hz.
[ERROR]HFP plus HBP is not greater than d_phy, the panel may not work
properly.
BUG=b:284812193
TEST=cbmem -c | grep "ERROR" and measure frame rate
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7de5984ce8aec12d8ebe292974e05776835330d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76218
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some of the error messages of checkpatch.pl contain "*". Since now
Gerrit supports markdown, messages with "*" will be rendered
incorrectly. For example,
foo* bar should be foo *bar
will be shown as
foo bar should be foo bar
with "bar should be foo" being in italics. Fix the problem by
surrounding the output message with "`" to make it verbatim.
Change-Id: I02d0e894adf7f94a9e154f99321f51d4097963a5
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76392
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
This patch updates the MemInfoHob header file as per Meteor Lake
version 3251.81.
Changes include:
1. Drop DimmDFE structure variable
2. Drop unused macro MAX_COPY_DIMM_DFE_TAPS
BUG=b:290898626
TEST=Able to build and boot google/rex.
w/o this patch:
cbmem -c -1 | grep DIMM
[ERROR] No DIMMs found
w/ this patch:
cbmem -c -1 | grep DIMM
[DEBUG] 8 DIMMs found
Change-Id: I8eed410831399bb4835244f48c14d5ed9e701e68
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76433
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Per the suggestion in CB:76218, print actual values to the error
messages, which may be helpful for debugging.
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Id3a7a8c76b6ad15e7cf71225d8529f3e034935ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76442
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
When set to 1, the link_compliance_mode element of the DXIO port
descriptor will cause the corresponding PCIe port to not be trained but
to output a compliance testing pattern instead. Update the comment to
point out that this is only a testing mode.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaabb16c51a0c08391cd2d63b8064c524a748ccb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76441
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
This configures GPIO IO Standby State of GPP_F00 - GPP_F05 as masked
for CNVi.
Meteor Lake rex platform does not wake up from low power state by
bluetooth keyboard and mouse properly. It is identified that IO Standby
State needs to be configured as masked to function properly for CNVi.
BUG=b:286803481
TEST=Make screebo suspend to s0ix state and press a key from
bluetooth keyboard. Check the platform wakes up properly from s0ix.
Change-Id: I7fd342e52fa0f9126eab4c857a5adc04c26e49c6
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76406
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCR (Private Configuration Register) is applicable to access the
P2SB register space starting with the Intel SkyLake generation of SoC.
Prior to Intel Meteor Lake SoC generation, the only P2SB existed inside
the PCH die. Starting with Meteor Lake SoC, there are two P2SB, one in
SoC die (same as PCH die for U/H SoC) and another in IOE die.
This patch renames pcr.asl to pch_pcr.asl to reflect the actual source
of the P2SB IP in the die (i.e., SoC die or PCH die).
BUG=b:290856936
TEST=Able to build and boot google/rex.
Change-Id: Idb66293eaab01e1d4bcd4e9482157575fb0adf04
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76407
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
GMBus is an I2C compatible link on Intel IGPUs. Most non-Linux OS's
don't support accessing this ordinarily, so a custom driver is
needed with a bit of ACPI hackery. Reserve 2 IDs from the
coreboot namespace so that the 2 devices required can be populated
in Windows device manager
Change-Id: I389612441e96ce2fc5e006051e523661953eba6e
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Pujjo support WWAN EM060 device, use FW_CONFIG to handle the
power on sequence.
BUG=b:290709711
TEST=Build and check WWAN EM060 power on sequence.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I66800c75274e8e1e55d4314c82b7fcdf2a4477bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76403
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cannon Lake, which covers Coffee Lake and Comet Lake, has been missing
from the maintainers file. Most unmerged patches for it have recently
been abandoned after 2+ years of inactivity.
Change-Id: Ic381f8efc4a423dca83c36605002aeeabf4bfdd9
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
With the latest hardware revision, the polarity of GPP_B5 has been
changed. For a full-populated DRAM configuration, the input signal is
now connected to 3.3 V and for a half-populated configuration it is
connected to ground.
BUG=none
TEST=Use different populated mainboards and check coreboot log
GPP_B5 = 0:
[INFO ] meminit_channels: DRAM half-populated
[DEBUG] 1 DIMMs found
GPP_B5 = 1:
[DEBUG] 2 DIMMs found
Change-Id: Iaa3a63fa52c802d8f5d8c6cc11dd6edfac117e88
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76434
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Modify reset_delay_ms from 300ms to 6ms for ELAN EKTH7D18.
BUG=b:285999032
BRANCH=firmware-nissa-15217.B
TEST=boot uldren to ChromeOS and touchscreen is workable.
Change-Id: Iffcddbe7735b7a837887dec68e1270c2af5f4556
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76417
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Disable scalability tracking for autonomous frequency control in
order to improve power and performance.
BUG=b:280021171
TEST=Boot to OS on brya0
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: If71ee5374c67611b32691bbec4effdf828b3e566
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74723
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Hook the newly exposed EnableHwpScalabilityTracking UPD up so that
boards can configure is via devicetree.
BUG=b:280021171
TEST=Verified by enabling/disabling the UPD on google/brya
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I4c8845c445d46caa30a0245386ab9cd690d2623f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74722
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Hook the newly exposed DisableSagvReorder UPD up so that
boards can configure is via devicetree.
BUG=b:268546941
TEST=Verified by enabling/disabling the UPD on google/brya
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I89235d9384b67f03e68425aadd3458e1c77ff555
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Disable re-ordering SaGv point on warm reset so that most
performant SaGv point is picked after memory training and
boot time is reduced.
BUG=b:268546941
TEST=Observe boot time improvement with these two UPDs set
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I44a1c054d52bb8585a320bb8a52a8f137e639804
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74721
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable upd to reduce size of the memory test.
BUG=b:268546941
TEST=Observe boot time improvement with these two UPDs set
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I95c7d8503596c2712d7abe123ed1f911ac4abacf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tyler Wang