Modify the vbios's eDP signal setting from level0(0dB)
to level1 (3.5dB) for bard
Add VBT blobs and include it in cbfs
BUG=b:119448457
TEST=Test & measure eDP signal
Change-Id: I0b854a6adad43844282aed61d26e798727b5cb62
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30375
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds a convenient helper function to add vbt binaries to cbfs.
Change-Id: I80d9b3421f6e539879ad4802119fe81d7ea1e234
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30430
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The H81 chipset is the only non-LP Lynx Point chipset with 6 PCIe root
ports, all others have 8 [1]. The existing PCIe code assumed that all
non-LP chipsets had 8 root ports, which meant that port 6 would not be
considered the last root port on H81, so `root_port_commit_config()`
would not run. Ultimately, while PCIe still worked on H81, all the root
ports would remain enabled, even if disabled in the devicetree.
Also, remove `PCI_DEVICE_ID_INTEL_LYNXPOINT_MOB_DESK_{MIN,MAX}`, as they
are unused, and the MAX constant is incorrect.
Interestingly, this fixes an issue where GRUB is unable to halt the
system.
Tested on an ASRock H81M-HDS. The root ports disabled in the devicetree
do indeed end up disabled.
[1] Intel® 8 Series/C220 Series Chipset Family Platform Controller Hub
(PCH) Datasheet, revision 003, document number 328904.
Change-Id: If3ce217e8a4f4ea4e111e4525b03dbbfc63f92b0
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30077
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to issue tracker b:119238959 #4 & #6.
Hardware modify design to make GPP_E3 to be a switch of touchscreen
I2C CLK and SDA.
Control GPP_E3 to make touchscreen I2C CLK and SDA keep low during
power on initialization to avoid data transfer during this time.
After touchscreen IC initial complete, control GPP_E3 to high to
make touchscreen I2C CLK and SDA work normally.
Depending on touchscreen IC specification, device take 105ms for
power on initialization.
Change delay time from 120ms to 105ms.
BUG=b:119238959
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, run S5 stress test and verify the result
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86452c1445243c499aeaf931dba286db169c5628
Reviewed-on: https://review.coreboot.org/c/30180
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Platforms moved to POSTCAR_STAGE so these are no longer used.
Change-Id: I9a7b5a1f29b402d0e996f2c2f8c6db3800cdddf3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch modifies the hatch flash layout to support
IFWI 1.6 with the following regions,
Flash Region 0: Descriptor
[0x0 - 0xFFF]
Flash Region 1: IFWI (consist of ME and PMC FW)
[0x1000 - 0x3FFFFF]
Flash Region 2: BIOS
[0x1400000 - 0x1FFFFFF]
Change-Id: I3d05fb50e970737a2552b85d6aebed943bf2b6cb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30413
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Platform has been moved to C_ENVIRONMENT_BOOTBLOCK and this
file was for romcc bootblock.
Change-Id: I2c249b18edd41c9a7798400d24b1c9228422d59b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This mainboard has the BSEL straps hooked up to the SuperIO
similar to the ASUS P5GC-MX and might therefore require a restart.
Tested:
- FSB 800, 1067 and 1333MHz CPUs
- USB
- Ethernet
- Serial
- 2 DIMM slots
- SATA
- Libgfxinit (VGA)
TESTED with SeaBIOS (sercon disabled) and Linux 4.19.
Change-Id: Id845289081751ff8900e366592745f16d96f07c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
At the moment, this just gives some details on the MRC.
Change-Id: I84e8ca2543b2e19b84a24f7d7032a4aedb6e9272
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Any board that uses the AST driver will have support for native graphics
init. So, select the option in the driver instead of every board.
Change-Id: I2bf42c168d1ffdda11857854889b74953abd7e40
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fix the following warning shown in dmesg:
"ACPI BIOS Warning (bug): Incorrect checksum in table [FACP]"
The table checksum was wrong as it was calculated twice and with the second
time the checksum field wasn't set to zero.
Change-Id: I375354bf3e95ebdac3b0dad43659d72c6ab3175a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Remove all cases in code where we tested for
EARLY_CBMEM_INIT or LATE_CBMEM_INIT being set.
This also removes all references to LATE_CBMEM_INIT
in comments.
Change-Id: I4e47fb5c8a947d268f4840cfb9c0d3596fb9ab39
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/26827
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Migration of globals is not needed as there is no real CAR that
gets torn down.
Change-Id: Id24642b49fab811e59291747eda8632cd49d83d0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This reverts commit a914152fa6.
Reason for revert:
According to the partner on this project, custom values like this
are no longer necessary.
Change-Id: I393eb4997f58abe0f77161999474994f06741519
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Report correct board information for Whiskeylake RVP to OS.
Use short board name like other RVP as it's used
for firmware version check in auto test.
Change-Id: I3f7c95f136e39b978a335cc7855cac819043db7c
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-on: https://review.coreboot.org/c/30318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Some boards may want to initialize watchdog in verstage instead of
bootblock or ramstage, so we need to add watchdog support in verstage.
BRANCH=none
BUG=b:120588396
TEST=build successfully
Change-Id: I13ab84f54d576a0e8c723070b5d9aadd9d63f87c
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Refactor function mtk_spi_set_gpio_pinmux to reduce compiled code size.
This change can save us about 552 bytes (before compression).
Idea from Julius's comment in https://review.coreboot.org/c/coreboot/+/27498/4
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I93bc88c535b6a2ff94e85f247cf2d51f60b9b29c
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Ren Kuo