Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635f ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
FIT support takes more heap memory than most coreboot payloads.
Change-Id: Id17f25e94d97e937b0e9a9cee3dd1a8aef1d525d
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If override tree does not have any device, then the chip info
structure in it cannot be associated with the correct device and ends
up being added as a standalone chip info structure without any device
actually using it. This change prevents this condition by throwing an
error during compilation.
BUG=b:130342895
Change-Id: I7b8bb6b3228030a465976ca32ce8ef63f41365dd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Modify the POWER_OFF_ON_CR50_UPDATE Kconfig option so that specific
mainboard implementations can disable the option.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I3beefaae21de61e53ae232dbdc8ea9dbb2c78cd5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set CPU frequency from 1100MHz to 1989MHz to improve booting time.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: Id41c7ea8905c4db2537a5c32f96eb7c6b2c008ea
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32397
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The maximum CPU frequency is 1417MHz with current processor voltage
(0.8v). Set processor voltage to 1.05v for higher CPU frequency.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I24ecdac2c85d3f012d9235449c0d727d727dc185
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The Kconfig file has been updated to show 1.12.1 but this is only
what gets displayed for the "stable" option. Fix this by updating
the actual git hash for the SeaBIOS 1.12.1 release tag.
Fixes: fb83ff1a8b ("Update stable from 1.12.0 to 1.12.1")
Change-Id: I76dc0dc8b651df0c6ff6f3c02819a70bab8c04cd
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tune I2C params for I2C buses 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:131132499, b:128998988
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Ie8cfba72a0654402ccb0274c00b44fbfa2deea21
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update SPI enable/disable and configure clock
API for supporting all the blsp and qup for qcs405.
Change-Id: I39622571cb671f62312283a010129ceecb654f61
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Fixes src/northbridge/intel/sandybridge/raminit_mrc.c:286:3: error:
implicit declaration of function 'enable_usb_bar'
Change-Id: I48bf59c56b518477a3fc0d75902fc58df6b7def7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32400
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change-Id: Ic23eb57a4096d4301d7f9478d8e65aaeb233de7b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32399
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The last attribute was never returned.
Fix size compare to retrieve all attributes.
Manually tested and seen all attributes, including the last one.
Change-Id: I08df073158a0f285f96048c92aa8066fa4f57e6f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7669b8dc07b1aa5f00e7d8d0b1305b3de6c5949c
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Kconfig somehow adds spurious booleans for each alternative when the
choice itself has a name. That's fixed simply by removing the name.
Change-Id: Ic35f0697f1f7bb92c12414c17a8790464b376012
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
When coreboot checks the TPM and key-ladder state it issues a reboot of
the Cr50 with a delay parameter. Older Cr50 code doesn't support the
delay parameter and reboots immediately, which prevented coreboot from
running the mainboard specific code needed for the AP to come back up.
This change calls mainboard_prepare_cr50_reset() prior to sending the
VENDOR_CC_IMMEDIATE_RESET command.
This change also fixes a false error message from the coreboot log that
indicated "Unexpected Cr50 TPM mode 3" when the Cr50 key ladder is
disabled.
BUG=b:130830178
BRANCH=none
TEST=build coreboot on sarien and grunt platforms.
TEST=Load Cr50 v3.15, run 'gsctool -a -m disable; reboot'. Verify
corebot send the
VENDOR_CC_IMMEDIATE_RESET command and that the AP boots normally.
Verify event log shows "cr50 Reset Required"
TEST=Force Cr50 automatic update. Verify event log shows "cr50 Update
Reset".
Change-Id: Ib05c9cfde8e87daffd4233114263de5b30822872
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Declare plaform level hook method before and after system sleep for
possible power management related usage.
BUG=N/A
TEST=pass with make what-jenkins-does
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie63711748b6dbb99d34910824f2059464543e162
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32366
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without VBOOT_MEASURED_BOOT there is no need for these symbols.
Change-Id: I96391b7817c79f760713c67bc469164b5514879e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Commit 45d4b17 [nb/intel/sandybridge: Move southbridge code to bd82x6x]
moved early_pch_init() to the southbridge, but failed to include
early_pch.c for the non-native raminit case, which now fails to link.
As all boards default to native raminit, this was missed by the autobuilder.
Adjust early_pch.c to be compiled regardles of ram init type used
Test: build/boot google/stout with MRC ram init selected
Change-Id: I50db30fda9a1099fb434c04ea97bcc38f8455233
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
For full reset, use already defined full_reset() function.
Change-Id: Iec7dcf285f3cb1cdc8f48d348ff8496879625db5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This allows for serial console during the bootblock and enables
console in general for the bootblock.
Change-Id: I5c6e107c267a7acb5bf9cbeb54eb5361af3b6db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30315
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Parameter passing is incorrect here, it should pass
complete StdHeader instead of attempting to fill
in HeapStatus that should be treated as a field private
to AGESA, based on where it is defined in the header
files.
Furthermore the while() loop did not evaluate the
return value. Feature can be brought back at a later
date after someone verifies it actually works correctly
across different stages.
Change-Id: Ib243b275f8700ecaeb330772c795d305c61899c5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31484
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Each entrypoint to AGESA goes through the same sequence
and have same the function signature.
To avoid introducing bunch of preprocessor magic, rename
all the agesawrapper_amdXXX() functions that are actual
entrypoints to AGESA API, make them static, and provide
a single exposed entry function agesa_execute_state().
Change-Id: I96ae1874132da3843aa42c2f4e8a59ec771d3893
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31483
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Add SMBIOS type 9 system slots into coreboot, the definiation is up to
date with SMBIOS spec 3.2
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibcfa377c260083203c1daf5562e103001f76b257
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change is mainly to control PlatformDebugConsent FSP UPD.
PlatformDebugConsent is enabled if SOC_INTEL_CANNONLAKE_DEBUG_CONSENT != 0.
PlatformDebugConsent in FspmUpd.h has the details.
BUG=b:130203864
TEST=boot ok and PlatformDebugConsent can be controlled by Kconfig
Change-Id: Ib845b5e42bc78fb352a0c97c6301f2aeca522f29
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32297
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Linux remains using SPI1 and PWM ASL even if these devices are disabled.
SPI1 and PWM are disabled by Intel FSP.
Remove ASL code.
BUG=N/A
TEST=Boot Ubuntu on Intel CherryHill CRB
Change-Id: Iec2ca7520081d00bf7a53d58ee054aa6f23e5606
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Serial bus revision [Byte 3] and serial bus specific revision [Byte 9]
are not the same.
Change-Id: I366f62e6aa0e9c0dfbc1ec17adeebc42a0e777eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Include pch.h in the source files instead in sandybridge.h.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I9e5b678e979a8d136d8d00b49486d0a882f77d81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Support for ACPI specification version 6.3:
Add PCC operation region support for the AML interpreter. This adds PCC
operation region support in the AML interpreter and a default handler for
acpiexec. The change also renames the PCC region address space keyword to
PlatformCommChannel.
Support for new predefined methods _NBS, _NCH, _NIC, _NIH, and _NIG.
These methods provide OSPM with health information and device boot
status.
PDTT: Add TriggerOrder to the PCC Identifier structure. The field value
defines if the trigger needs to be invoked by OSPM before or at the end
of kernel crash dump processing/handling operation.
SRAT: Add Generic Affinity Structure subtable. This subtable in the SRAT
is used for describing devices such as heterogeneous processors,
accelerators, GPUs, and IO devices with integrated compute or DMA
engines.
MADT: Add support for statistical profiling in GICC. Statistical
profiling extension (SPE) is an architecture-specific feature for ARM.
MADT: Add online capable flag. If this bit is set, system hardware
supports enabling this processor during OS runtime.
New Error Disconnect Recover Notification value. There are a number of
scenarios where system Firmware in collaboration with hardware may
disconnect one or more devices from the rest of the system for purposes
of error containment. Firmware can use this new notification value to
alert OSPM of such a removal.
PPTT: New additional fields in Processor Structure Flags. These flags
provide more information about processor topology.
NFIT/Disassembler: Change a field name from "Address Range" to "Region
Type".
HMAT updates: make several existing fields to be reserved as well as
rename subtable 0 to "memory proximity domain attributes".
GTDT: Add support for new GTDT Revision 3. This revision adds information
for the EL2 timer.
iASL: Update the HMAT example template for new fields.
iASL: Add support for the new revision of the GTDT (Rev 3).
More changes in this version at https://acpica.org/node/166
Change-Id: I3a825f568423c3a703ad1c13da976af322ed9de2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Release Note :
https://cmake.org/cmake/help/v3.14/release/3.14.html
"The FindFontconfig module added by 3.14.0 accidentally used uppercase
FONTCONFIG_* variable names that do not match our conventions.
3.14.1 revises the module to use Fontconfig_* variable names.
This is incompatible with 3.14.0 but since the module is new in the 3.14
series usage should not yet be widespread"
Change-Id: Ief7f5e8309597093f061789926bd3bd2ed3aec2d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tristan Corrick