gerrit-rebase is a gerrit-context aware rebase script. Given a source
and a target branch (that need to have a common ancestor), it prepares
a rebase todo list that applies all commits from source that aren't
already found on target.
It matches commits using Reviewed-on lines in the commit message that
are added by gerrit when submitting commits using the "cherry-pick"
strategy.
This has been shown to be the best preserved meta data to work from in
existing data (Change-Id was mangled in all kinds of ways).
Change-Id: I9618c1b66ebc1fb7ed006efbc1665fb08386e1a5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/16695
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch adds MAINBOARD_HAS_NATIVE_VGA_INIT_TEXTMODECFG to the
gigabyte/ga-g41m-es2l Kconfig to allow selecting between textmode and
vesamode in menuconfig.
Change-Id: I84b61118fa0419d49d2498b66029711cdce97576
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16501
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch implements native resolution, VESA mode, on the VGA output of
x4x.
It relies on EDID to modeset, but has a fallback-mode (640 x 480 @
60Hz) if this is no EDID could be found. This fallback mode only works
in textmode since in VESA mode some payloads (grub2) rely on VBE info,
which is being generated from an EDID.
Change-Id: I247ea7171ba3c5dc3b209d00e4dcb2d2069abd75
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
flashrom treats them as invalid because start > end.
Change-Id: I1c8b4563094823ebd9b1193b91e7b4a748955228
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16936
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Maxim98357a speaker amp requires BCLK & SFRM to be active
and stable before it is unmuted. If there is a BLCK and no
SFRM, it results in a pop sound.
sdmode_delay property already exists which facilitates this
configuration. This patch updates "sdmode_delay" to avoid
pop sound.
BUG=chrome-os-partner:58356
BRANCH=None
TEST=while audio playback via headset, remove headset.
Audio will be switched playback to speaker. Observe if
pop sound comes from speaker.
Change-Id: I7ad68caa88d7b3ff52ac1379fe6564de27d97777
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/16933
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The datasheets "Intel® Core™ Duo Processor and Intel® Core™ Solo
Processor on 65 nm Process" mentions cpu C-states substates which can
either be attained by adding a substate hint to the MWAIT/P_LVLx request
or automatically by setting some msr bits correctly.
This just sets the same msr bits as model_6fx to enable
dynamic L2 cache, C2E and C4E acpi cpu states.
The result is that when limiting a thinkpad x60 with a yonah T2400
cpu to the acpi cpu C2 state, the idle power usage drops from 18W to
14W. When the lowest C-state is set to C4 the idle power usage seems
to remain similar.
Change-Id: I6c422656ace04659f32082a5944617eda6c79ec3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16901
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
max_regions is set to the maximal regions based on the ifd version
Change-Id: I9fa5a4565f4dbd67b5c6df97756311560e2a18bc
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/16934
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
When timestamp is enabled, the system hangs because the timestamp data
is not yet available. Add a temporary work around that starts the
timestamp after the FspInit() making this data available.
Verified on Intel Camelback Mountain CRB and ensured that system can
boot to payload with timpstamp feature enabled.
Change-Id: I59c4bb83ae7e166cceca34988d5a392e5a831afa
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: https://review.coreboot.org/16894
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The enforced FSP 1.0 APIs call was used to work around an fsp1.0 driver
issue. As the issue has been addressed in fsp1.0 driver (Change 9780),
remove the enforced workaround. Otherwise will see error message
'FSP API NotifyPhase failed' in serial log.
Verified on Intel Camelback Mountain CRB and confirmed that the serial
log error message regarding the 'FSP API NotifyPhase failed' is gone.
Change-Id: Iafa1d22e2476769fd841a3ebaa1ab4f9713c6c39
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: https://review.coreboot.org/16892
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
When compiling a non-x86 platform with DRIVERS_INTEL_WIFI enabled,
we get the build error:
src/drivers/intel/wifi/wifi.c:17:30: fatal error:
arch/acpi_device.h: No such file or directory
acpi_device.h only exists in the x86 architecture directory.
Change-Id: Id0e29558336bf44e638cfcb97c22f31683ea4ec7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16906
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Some PVT units encountered DRAM calibration failure during
power on/off tests. The failure is caused by higher impedance
of the DRAM on those units. So increase the driving strength
for 4GB DRAMs.
BUG=chrome-os-partner:57392
TEST=run cold reboot 100 times on PVT units which have DRAM
calibration issue.
Change-Id: I8a329093db3f1def566e4b7afec3c4f4bfe44c6a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf1aa5ade856af433fa056f51a20d18553ae241d
Original-Change-Id: I0d1776cd1a5892d1f82e9bf414620d1ef6d29132
Original-Signed-off-by: PH Hsu <ph.hsu@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/394451
Original-Commit-Ready: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-by: Pin-Huan Hsu <ph.hsu@mediatek.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/16917
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We found that Kevin board PHY0 and PHY1 eye-diagram margin
is not enough to make compliance test pass, and the PHY0 USB
SI is worse than PHY1, because of the higher PCB impedance.
For PHY0, we can't improve the eye-diagram by SW PHY tuning,
so we need to reduce the RBIAS resistance from 133 ohm to 115
ohm, it can help to increase the eye-height.
For PHY1, we can improve the eye-diagram by setting the max
pre-emphasis level.
And after the above change, the USB2 signal amplitude will
become larger at the test point near to SOC USB2 PHY, in order
to avoid mis-trigger the disconnect detection (650mV), we need
to disable pre-emphasize in eop state.
BRANCH=None
BUG=chrome-os-partner:53863
TEST=do USB 2.0 compliance test for Kevin C0 and C1 port.
Change-Id: I95c0acd79623aeca9a0ae077b1dd3836d91fe561
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de3cdef128966d76e7d8e2ebd641763b911c3ad5
Original-Change-Id: I00cb325b9938e4276cc77b5d6f5faa7023379608
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/390615
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16911
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Though we don't use Type-C PHY to support USB3 in firmware,
we still need to initialize the Type-C PHY, and make sure
the power state of pipe is always fixed to U2/P2. After
this, we can force USB3 controller to work in USB2 only
mode.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: I95bb96ff27d4fecafb7b2b9e9dc2839b5c132654
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8ec98507845276119d8a9d5626934dedcb35f2dd
Original-Change-Id: Ie3654cd1c1cb76b62aa9b247879b60cbecee0155
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/391412
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16910
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We do this so that the riscv objdump can be used on the coreboot.elf file.
Change-Id: Ib8bf85a3299dd75b779e7fa3757f5b62c9c7170b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/16918
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Converged Security Engine (CSE) has a secure variable storage feature.
However, this storage is expected to be reset during S3 resume flow.
Since coreboot does not use secure storage feature, disable HECI2 reset
request. This saves appr. 130ms of resume time.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=powerd_dbus_suspend; resume; check time with cbmem -t. Note
FspMemoryInit time is not significantly different from normal boot
time case.
Change-Id: I485a980369c6bd97c43b9e554d65ee89e84d8233
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16870
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
These header files contain a few new UPDs. The EnableS3Heci2
UPD will be used to save ~100ms from the S3 resume time on
Apollolake chrome platforms.
BUG=chrome-os-partner:58121
BRANCH=none
TEST=built coreboot for reef and verified no regressions
Change-Id: I1f324d00237c7150697800258a2f7b7eed856417
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16869
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
commit 028200f7 - x86/acpi_device: Add support for GPIO output polarity
updated ACPI_GPIO_OUTPUT to ACPI_GPIO_OUTPUT_ACTIVE_HIGH for the other
boards that needed it, but pyro wasn't in the tree when it was initially
pushed. Now that pyro is in the tree, it needs to be updated as well.
Change-Id: I617999b06ee584e0543d7ae3232bb2be2ff7429c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16930
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Between GNU Tar 1.28 & 1.29, the files excluded by --exclude-vcs was
updated. This breaks the reproducibility. Instead, just manually
exclude the files to match what was excluded in v 1.28 and earlier.
Change-Id: Ie0717891506f4a6d750ff264f9cc2494a296265b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16900
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
- Add more help text.
- Remove braces from variables where the variable is isolated.
- Remove --recurse-submodules from clone. This breaks on old coreboot
versions.
- Add some whitespace between blocks.
- Fix all shellcheck warnings.
- Verify tar version and fail if it doesn't support --sort.
Change-Id: I4a49df99532d9a92a4a05bceff16f96a4fc3e205
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16883
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch enables stage cache to save ~40ms during S3 resume.
It saves ramstage in the stage cache and restores it on resume
so that ramstage does not have to reinitialize during the
resume flow. Stage cache functionality is added to postcar stage
since ramstage is called from postcar.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=built for Reef and tested ramstage being cached
Change-Id: I1551fd0faca536bd8c8656f0a8ec7f900aae1f72
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16833
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Instead of hard-coding the polarity of the GPIO to active high/low,
accept it as a parameter in devicetree. This polarity can then be used
while calling into acpi_dp_add_gpio to determine the active low status
correctly.
BUG=chrome-os-partner:55988
BRANCH=None
TEST=Verified that correct polarity is set for reset-gpio on reef.
Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/16877
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Elyes HAOUAS