Only input from the BJ port is wired to VSYS on Kalista. VBUS from
USB-C is for output only. In other words, Kalista is a source only
device from a USB/PD perspective.
This patch disables EC-EFS, which would be needed for the EC to jump
to RW to get PD power before the AP boots. Kalista will be always
supplied enough power to boot the AP through the BJ port.
CQ-DEPEND=CL:1330171
BUG=b:118386511
BRANCH=none
TEST=Boot Fizz. Verify normal boot, soft sync, recovery mode work.
Change-Id: Icd18662ae1e76f35eb9bcd521b1951aacc713252
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/29564
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Refactor PMIC wrapper code which will be reused among similar SoCs.
Move reusable code into the common folder.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot
Change-Id: I25acb6da49e72748d856804ef4f97e9ec3bef72d
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/29420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Braswell allready supported vmx, but offered no mechanism to unset it, nor
to set the lock bit required for Windows to recognize virtualization.
Enable this functionality by adding CPU_INTEL_COMMON config.
Test: build/boot Windows 10 on Braswell ChromeOS device, verify Windows shows
virtualization as enabled.
Change-Id: I0d39abaeb9eebcceb37dc791df6b06e521fe1992
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/29570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
GPP_D0 is NC in 1st SKU board design, so we should control GPP_D0
for only 2nd SKU.
BUG=none
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ifd85693c9155ed960f0c794d4b83fe8863b77134
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/29631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The GPP_E1 gpio was incorrectly being defined as a no-connect.
Configure GPP_E1 for the WLAN_WAKE_L signal as per the schematic.
BUG=b:119508897
TEST=Build and flash nocturne, boot nocturne and
1) Verify nocturne can successfully suspend/resume from S3 and S0ix.
2) Verify wake from wlan wakes device from S3 and S0ix.
To do so,
a) as root, execute "iw phy phy0 wowlan enable disconnect" on DUT
b) connect DUT to mobile hotspot
c) sleep device via "powerd_dbus_suspend"
d) turn off hotspot, verify DUT wakes from S0ix
e) enable hotspot again
f) connect DUT to hotspot
g) sleep DUT via "sudo echo mem > /sys/power/state"
h) turn off hotspot, verify DUT wakes from S3
Change-Id: I4efb4f6d601e172ae4807901e3bd4c9954319f80
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add an unprocessed flag (-U) which modifies how files are exported.
In the case of a compressed raw file, extract without decompressing.
In the case of a stage or payload, extract without decompressing or
converting to an ELF.
This can be useful for verifying the integrity of a stage or payload,
since converting to an ELF may not be a deterministic process on
different platforms or coreboot versions.
BUG=b:111577108
TEST=USE=cb_legacy_tianocore emerge-eve edk2 coreboot-utils chromeos-bootimage
cd /build/eve/firmware
/build/eve/usr/bin/cbfstool image.bin extract -r RW_LEGACY \
-n payload -f /tmp/payload_1 -U
START=$((16#`xxd -s 20 -l 4 -p tianocore.cbfs`))
SIZE=$((16#`xxd -s 8 -l 4 -p tianocore.cbfs`))
dd if=tianocore.cbfs skip=$START count=$SIZE bs=1 > /tmp/payload_2
diff /tmp/payload_1 /tmp/payload_2
rm /tmp/payload_1 /tmp/payload_2
Change-Id: I351d471d699daedd51adf4a860661877f25607e6
Signed-off-by: Joel Kitching <kitching@chromium.org>
Reviewed-on: https://review.coreboot.org/29616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The common SPI controller driver in src/southbridge/intel/common does
match the SPI controller included in the PCH of Broadwell-DE SoC. Switch
to the usage of this driver and delete the dedicated one for the FSP
based Broadwell-DE implementation.
TEST: Boot mc_bdx1 with SPI driver active in romstage
Change-Id: I4fe8057ea1981e350659a5caa9912fb758110115
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/29633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add a `docker-run-local` target that is used as a template for the
local build targets (`docker-build-coreboot`, `docker-abuild`, and
`docker-what-jenkins-does`).
Note this changes the user for `docker-what-jenkins-does` which has
(ccache) issues if it's not `root`. Will be fixed in a follow-up.
Change-Id: I9088fb9211726cddc37b17ddf70170c2c382679e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
There are several files under soc/amd that use units defined by file
porting.h. These units use upper case, and are not recognized by checkpatch,
thus causing problems when defining a pointer (request to use space before
and after the star symbol). These are the definitions from porting.h showing
the units that this patch will change and their coreboot definitions (not all
are actually used):
typedef uintptr_t UINTN;
typedef int64_t INT64;
typedef uint64_t UINT64;
typedef int32_t INT32;
typedef uint32_t UINT32;
typedef int16_t INT16;
typedef uint16_t UINT16;
typedef int8_t INT8;
typedef uint8_t UINT8;
typedef char CHAR8;
typedef unsigned short CHAR16;
typedef unsigned char BOOLEAN;
typedef void VOID;
BUG=b:118775313
TEST=Build and boot grunt.
Change-Id: Ic1bd64d6224a030a65d23decabf0e602cee02871
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Pointer math with void pointers is illegal in many compilers, though it
works with GCC because it assumes size of void to be 1. In this particular
situation, dev->buf is already pointer to u8, and there's no need to convert
to void *.
BUG=b:118484178
TEST=Build libpayload.
Change-Id: Ib70b8ce11abc88c35be4092f097cfff385921f46
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Pointer math with void pointers is illegal in many compilers, though it
works with GCC because it assumes size of void to be 1. Change the pointers
or add parenthesis to force a proper order that will not cause compile
errors if compiled with a different compiler, and more importantly, don't
have unsuspected side effects.
BUG=b:118484178
TEST=Build CBFS with original code, run objdump and saved output. Added
modifications, build cbfs again, run objdump again, compared objdump outputs.
Change-Id: I30187de8ea24adba41083f3bfbd24c0e363ee4b8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Function write_pci_cfg_irqs() has "no function" variables. One variable is
set and never used, the other is only used to control a print. Remove them.
BUG=b:117950052
TEST=Build grunt.
Change-Id: Icd98db3e794e609b112f15979a3a00a2977a0fdb
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Value stored to 'cmd' is never read
Change-Id: I794b6e12f5af272705cd996f7ca5099e9b9dbfc7
Found-by: scan-build from clang 6
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/29568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Currently, there is nothing for this mainboard to do in ramstage.
Change-Id: Id74a5f3f0a0583dc6bc81044913b8bb83d3b0b93
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard is equipped with LPDDR4 modules. The corresponding memory
swizzle data must be set for this purpose.
Change-Id: I4017de0713f0df5e614086912fc39d8eb6562702
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/29624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Pöche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
OEM name can be stored in CBI. This change can support for fetching
the OEM name from CBI.
BUG=b:118798180
TEST=Verified to get data from CBI
Change-Id: I4938c4d60fcad9e1f43ef69cc4441d1653de7e24
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/29497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Currently mode-aware DPTF depends on Tablet Mode Switch to load the
right table. This does not scale well with device types and configuration.
This change helps to decouple the mode-aware DPTF from Tablet Mode Switch.
This change allows ACPI to load the appropriate DPTF table based on the
profile number as detected by EC.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes(base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: Ibffe9c58f970aec37aa74a040170c4cf559bab33
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29249
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to support Multi-DPTF profile, Device DPTF Profile Number is
introduced into EC_ACPI_MEM_DEVICE_ORIENTATION ACPI Space at offset
0x09. This bit field stays along with Tablet Mode Device flag.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes(base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: Ie14916ac16c50cbe0990021e2eb03d5121cd0e07
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Rename EC_ENABLE_TABLET_EVENT config as EC_ENABLE_MULTIPLE_DPTF_PROFILES
since it aligns with the use-case.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes (base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: If147f1c79ceaaed00e17ec80ec6c912a8f7a8c2e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This patch makes static PIRQ->IRQ mapping, where IRQ10 is mapped
to PBRC and IRQ11 is mapped for PARC/PCRC/PDRC/PERC/PFRC/PGRC/PHRC.
Change-Id: I8722e34841fe53a4d425202b915ac7838af0d859
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29629
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since PIRQ->IRQ mapping registers PxRC are not available after FSP-S call
due to PCH requirement change from CNP PCH onwards, hence making static IRQ
mapping for pci_irqs.asl and pcie.asl
Also remove unused irqlinks.asl from soc/intel/cannonlake/acpi/
Change-Id: I35e2ed150a1db195fc9ce13897e65b23fc8b7ca1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add a `util/gitconfig/test` subdirectory which will contain tests to run
as executable files, add a helper script.
Add a timeout test that verifies that gitconfig completes in under two
seconds (typical run time is ~30 ms). Add gitconfig tests to the
`testing` Makefile under the `test-tools` target.
Change-Id: Id46f905b9f782e67be97a65d10045c3345dc996b
Signed-off-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/23280
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
<vendor> seems to be confused about the meaning of our maintainers list.
I get the feeling some use it to organize corporate internal teams and
branches, adding names to the list that don't show up in Gerrit and even
if, often don't react to reviewing requests (within months). Maybe they
even don't know that this is about coreboot.org?
To clarify this:
o Add an introductory paragraph mentioning development on coreboot.org.
o Explicitly state that maintainers should be registered to Gerrit.
o If a topic is tagged as `Supported` or `Maintained`, expect that
somebody reacts to review requests.
Change-Id: I9ee038dc5ee1f4993ba1d230ef6e737f20e2ff8a
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/29471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Guckian
Current implementation works by luck as DCACHE area is actually RAM and
stack can grow and use that RAM outside of the area.
* Set DCACHE_BSP_STACK_SIZE to 0x4000.
* Add an assert to make sure it is set to a sane value on all platforms.
Change-Id: I71f9d74d89e4129cdc4a850acc4fc1ac90e5f628
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/29611
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The gerrit reviewers plugin has a certain configuration format. Teach
maintainers to emit it when called with -print-gerrit-rules.
Change-Id: I92cfc905e0c1b03b7cf793a4324c392140a22060
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
First new option is -debug.
Change-Id: Ia6e9b3675449a0b1e6f5d7526ee999f925eaadb2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Help automated tools make sense of the output.
Instead of "[name 1 <email> name 2 <email>]", it now prints
"name 1 <email>, name 2 <email>". As long as there are no commas in the
maintainer names, they can be split easily.
Change-Id: I4a254f566404b081a08923bc7ceb49f02039aa2a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29604
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of checking only for three cases, just use a glob parser (that
translates the glob to regex).
After that, maintainers src/arch/x86/memlayout.h emits:
src/arch/x86/memlayout.h is in subsystem X86 ARCHITECTURE
Maintainers: []
src/arch/x86/memlayout.h is in subsystem MEMLAYOUT
Maintainers: [Julius Werner <jwerner@chromium.org>]
The latter entry was invisible to the maintainers tool because its path
description wasn't in one of the supported formats.
Change-Id: I7e5cf4269415269552e35f2c73952ce3dff487e1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Without this change, the tool only reports the first hit. We want to see
all of them.
Change-Id: Ib59b13c50b61c48e3cb200bf57e28c9453590819
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Add a helper function specific to ramstage to add the boot count
information into event log at ramstage.
BUG=b:117884485
BRANCH=None
TEST=Add an event log from romstage, boot to ChromeOS
Change-Id: Ic79f1a702548d8a2cd5c13175a9b2d718527953f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29542
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Group event log state information together to manage them better during
different stages of coreboot.
BUG=b:117884485
BRANCH=None
TEST=Add an event log from romstage, boot to ChromeOS
Change-Id: I62792c0f5063c89ad11b512f1777c7ab8a2c13e5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Daisuke Nojiri