Set the SOC_INTEL_COMMON_BLOCK_GPIO_LOCK_USING_SBI config on Alder Lake
to instruct Pad Configuration Lock to use non-posted sideband writes as
posted write is not supported on Alder Lake while locking GPIO pads.
BUG=b:211573253, b:211950520
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Id8d394b97de9c328b3f75df3649d7efc782f006b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This patch extends `struct pad_config` to add new variable for gpio
lock action.
Additionally, it creates new GPIO PAD configuration macros that perform
GPIO pad configuration and pad lock configuration as well.
List of new macros are:
1. PAD_CFG_NF_LOCK
2. PAD_CFG_GPO_LOCK
3. PAD_CFG_GPI_LOCK
4. PAD_CFG_GPI_TRIG_OWN_LOCK
5. PAD_CFG_GPI_GPIO_DRIVER_LOCK
6. PAD_CFG_GPI_INT_LOCK
7. PAD_CFG_GPI_APIC_LOCK
8. PAD_CFG_GPI_IRQ_WAKE_LOCK
Mainboard users can use the above macros to lock the PAD after
configuration.
So far on IA chipset, the default GPIO pad lock configuration reset
type is POWERGOOD hence, it's recommended as per GPIO BWG (doc: 630603)
to configure the GPP PAD reset type the same as lock configuration
reset type to avoid GPP reset value misconfiguration issue.
BUG=b:211573253, b:211950520
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibf8b0a845005ad545266d995449d0aa711f45a61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
This patch performs GPIO PAD lock configuration in non-smm mode.
Typically, coreboot enables SMI at latest boot phase post FSP-S,
hence, FSP-S might get chance to perform GPP lock configuration.
With this code changes, coreboot is able to perform GPIO PAD
lock configuration early in the boot flow, prior to calling FSP-S.
Also, this patch ensures to have two possible options as per GPIO
BWG to lock the GPIO PAD configuration.
1. Using SBI message with opcode 0x13
2. Using Private Configuration Register (PCR)
BUG=b:211573253, b:211950520
TEST=Able to build and boot brya variant with this code change.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I71b4e2f24303b6acb56debd581bd6bc818b6f926
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60801
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For one specific type of APU, it doesn't have HDMI. When we detect
this APU, we need to explicitly disable HDMI in DDI settings,
otherwise the system would freeze.
get_cpu_count() == 4 && get_threads_per_core() == 2: This case is for
2 Core and 4 Thread CPU (2C/4T for short).
get_cpu_count() == 2: This is for 2C/2T. This is for a possible future case.
BUG=b:208677293
Change-Id: I8d0fa96818a768b7960d92821b927dbc622675ae
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
This code is common to at least all Zen-based APUs (Picasso, Cezanne,
Sabrina) and is also useful outside of the SoC-specific dynamic ACPI
table generation code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie96d4429fb6ed9223efed9b3c754e04052d7ca7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-by: Eric Peers <epeers@google.com>
There is no wakeup source when we test function of suspend and resume.
The root cause is that the monitor enable bit of PWRAP is not configured
correctly.
BUG=b:213255218, b:214978483
TEST=receive wakeup source from MT6366 successfully
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I324d18fa5d3cd745c35fcf0f207e1b444b5e898b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61330
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The VERSTAGE region is only needed when running verstage in the x86.
This change reduces the early ram size by 512 KiB when using PSP
verstage.
BUG=none
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I45ce421397807dbb1eb48aedd05209b91e89aa4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reference test document, update tuning registers from pass experiment
setting of phy_settings.
The document about eDP tuning can be gotten from the issue tracker of
this ticket, at the issue tracker b/203061533#comment6.
BUG=b:203061533
Change-Id: I7aa8c594d9f5caa6b2523dac079aef89e623c56f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The FSP gets these values from the UPD and sets the internal values.
The document about eDP tuning is attached in issue tracker of this
ticket, at the issue tracker b/203061533#comment6.
BUG=b:203061533
Cq-Depend: chrome-internal:4303901
Change-Id: I9b85faac4f2fa1fb2c14bb85b615346d4379baac
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This reverts commit bd9b044a96 ("mb/system76: rtd3: Remove SrcClk pin
on CPU RP").
Previously, RTD3 expected a PCH index for the root port and did not work
with the CPU PCIe RP present on TGL, so SrcClk pin was disabled.
Set them now that RTD3 supports mapping the index for the CPU RP.
Change-Id: Ia7519b9f5a2be52cd5575615c28d20371a26996b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Taniks will use two PCIE port signals with one slot, one CLK and one
CLKREQ at next build. In order to accommodate this, probe statements
are added to the devicetree. This only affects NVME SSD and EMMC.
BUG=b:215040000
TEST=Build FSP with debug output enabled, and observe the correct root
ports being initialized depending on the FW_CONFIG values for BOOT_EMMC
and BOOT_NVME.
Cq-Depend:chromium:3397561
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I2ead505088f19fd3bf9768b541838395c82ef051
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
In order to guarantee data integrity an expired TCO must not hard reset
the board. Select the Kconfig switch to prevent this reset.
Change-Id: I04080c6bcd486e3a406438cc7a703165bb6945a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The TCO timer is the default watchdog of an x86 host and can reset the
system once it has expired for the second time. There are applications
where this reset is not acceptable while the TCO is used. In these
applications the TCO expire event generates an interrupt and software
takes care. There is a bit in the TCO1_CNT register on Elkhart Lake to
prevent this reset on expiration (called NO_REBOOT, see doc #636722 ).
This bit can either be strapped on hardware or set in this register to
avoid the reset on expiration. While the hardware strap cannot be
overridden in software, the pure software solution is more flexible.
Unfortunately, the location for this bit differs among the different
platforms. This is why it has to be handled on soc level rather than on
TCO common code level.
This commit adds a Kconfig option where NO_REBOOT can be enabled. This
makes it easy to reach this feature over to the mainboard where it can
be selected if needed.
Change-Id: Iaa81bfbe688edd717aa02db86f0a93fecdfcd16b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Prepares compilation for x86_64 by avoiding casts to different sizes.
Current patch fixes:
1.
src/northbridge/intel/i945/raminit.c: In function 'ram_read32':
src/northbridge/intel/i945/raminit.c:77:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
77 | read32((void *)offset);
| ^
2.
src/northbridge/intel/i945/rcven.c: In function 'sample_strobes':
src/northbridge/intel/i945/rcven.c:29:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
29 | read32((void *)addr);
| ^
src/northbridge/intel/i945/rcven.c:30:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
30 | read32((void *)(addr + 0x80));
| ^
3.
src/northbridge/intel/i945/gma.c: In function 'intel_gma_init_lvds':
src/northbridge/intel/i945/gma.c:98:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
98 | (void *)pgfx, mmiobase, piobase, pphysbase);
| ^
src/northbridge/intel/i945/gma.c:359:25: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
359 | (void *)pgfx, hactive * vactive * 4);
| ^
src/northbridge/intel/i945/gma.c:360:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
360 | memset((void *)pgfx, 0x00, hactive * vactive * 4);
| ^
src/northbridge/intel/i945/gma.c: In function 'intel_gma_init_vga':
src/northbridge/intel/i945/gma.c:384:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
384 | (u32)mmiobase, piobase, pphysbase);
|
4.
src/northbridge/intel/i945/northbridge.c: In function 'mch_domain_read_resources':
src/northbridge/intel/i945/northbridge.c:64:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
64 | cbmem_topk = ((uint32_t)cbmem_top() / KiB);
| ^
Change-Id: I5ac7a1cb5d85a346114f909047d5a7c21ddb43e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Chromebooks normally run with non-serial enabled firmware because
writing to the UART console is very slow. This unfortunately makes
debugging boot errors more difficult. We tend to rely on port 80s and/or
the vboot recovery code.
When CONSOLE_CBMEM_DUMP_TO_UART is selected it will dump the entire
cbmem console to the UART whenever `vboot_reboot()` is called. We don't
incur any boot time penalty in the happy path, but still retain the
ability to access the logs when an error occurs.
The previous implementation was using a hard coded UART index and
`get_uart_baudrate` was always returning 0 since `CONFIG_TTYS0_BAUD`
wasn't defined. This change makes it so the UART console properties are
available when CONSOLE_CBMEM_DUMP_TO_UART is set. This results in the
following .config diff:
+CONFIG_UART_FOR_CONSOLE=0
+CONFIG_TTYS0_BASE=0x3f8
+CONFIG_TTYS0_LCS=3
+CONFIG_CONSOLE_SERIAL_115200=y
+CONFIG_TTYS0_BAUD=115200
This functionality is especially helpful on Guybrush. PSP Verstage is
run on S0i3 resume. Today, if there is an error, the cbmem console is
lost since it lives in the PSP SRAM.
BUG=b:213828947, b:215599230
TEST=Build non-serial guybrush FW and verify no serial output happens in
happy path. Inject a vboot error and perform an S0i3 suspend/resume.
Verify CBMEM console gets dumped to the correct UART.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I997942204603362e51876a9ae25e493fe527437b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The FSP API is used to notify the FSP about different phases in the
boot process. The current FSP specification supports three notify
phases:
- Post PCI enumeration
- Ready to Boot
- End of Firmware
This patch attempts to make calling into the FSP Notify Phase APIs
optional by using native coreboot implementations to perform the
required lock down and chipset register configuration prior boot to
payload.
BUG=b:211954778
TEST=Able to build brya without any compilation issue and coreboot
log with this code changes when SKIP_FSP_NOTIFY_PHASE_READY_TO_BOOT
and SKIP_FSP_NOTIFY_PHASE_END_OF_FIRMWARE config enabled.
coreboot skipped calling FSP notify phase: 00000040.
coreboot skipped calling FSP notify phase: 000000f0.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia95e9ec25ae797f2ac8e1c74145cf21e59867d64
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Since Tiger Lake platform, the HECI1 device can be disabled on
Alder Lake platform using two different mechanism:
A. Using PMC IPC command 0xA9.
B. Sending SBI message under SMM.
In current scope of Alder Lake the default implementation is using
(B) sending sbi message under SMM. A follow up patch to add the
possible options and let platform to choose the applicable one.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
3. Default enable HECI1 device in `chipset.cb` to ensure the HECI1
device can undergo the PCI enumeration and later based on the
mainboard policy the HECI1 device can be disabled.
Mainboards that choose to make HECI1 enable during boot don't override
`DISABLE_HECI1_AT_PRE_BOOT` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie673e634fbc0bdece419c379d417b08dfb4819e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable PSE GBE with following changes:
1. Configure PCH GBE related FSP UPD flags
2. Add PSE GBE ACPI devices
3. Refactor PCH GBE FSP-S code and merge it together
with PSE GBE code
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: If3807ff5a4578be7b2c67064525fa5099950986a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The Intel® Programmable Services Engine (Intel® PSE) is a
dedicated offload engine for IoT functions powered by an ARM
Cortex-M7 microcontroller. It provides independent, low-DMIPS
computing and low-speed I/Os for IoT applications, plus
dedicated services for real-time computing and time-sensitive
synchronization.
The PSE hosts new functions, including remote out-of-band
device management, network proxy, embedded controller lite
and sensor hub.
This CL enables the user to provide the base address of the
PSE FW blob which will then be loaded by the FSP-S onto the
ARM controller. PSE FW will do the initialization work of
PSE controller and its peripherals. The loading of PSE FW
should have negligible impact on boot time unless PSE
controller could not locate the PSE FW and FSP will attempt to
redo PSE FW loading and wait for PSE handshake until it times
out. Once PSE controller locate the PSE FW, it will do
initialization concurrently by itself with coreboot booting.
It also adds PSE related FSP-S UPD settings which enable the
setup of peripheral ownership (assigned to the PSE or x86
subsystem) and interrupts. These assignments need to take
place at a given point in the boot process and cannot be
changed later.
To verify if PSE FW is loaded properly, the user could enable
PchPseShellEnabled flag and the log will be printed at PSE UART
2.
For further info please refer to doc #611825 (for HW overview)
and #614110 (for PSE EDS).
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ifea08fb82fea18ef66bab04b3ce378e79a0afbf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Constructed out of a mix of autoport results, p8z77-m_pro, and
tool dumps.
Working:
- Core i7-3770K CPU
- SeaBIOS 1.13.0 boot to Linux 5.4.24 and Windows 10 1903
(all further tests are under these versions)
- USB2 / USB3
- SATA
- Gigabit ethernet
- CPU temp sensors (memtest86+ 5.0.1)
- Hardware monitoring under Linux
- Native and MRC raminit
- PCIe GPU in both "PCIEX16" slots (16x/4x, nVidia Quadro 600)
- Integrated graphics with Intel OpROM and libgfxinit (all ports)
- Serial port
- Windows with libgfxinit framebuffer
- 2ch sound playback, Linux and Windows
Not working:
- PS/2 mouse
- 6ch analog audio out
- PCI POST card in PCI slot
Untested:
- PS/2 keyboard
- Internal USB3 ports
- Digital audio out
Change-Id: If756e791ddce747cb1706414be8e41e83f88922b
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Fast-k flow may need to re-init header because mrc_cache doesn't
store header. Storing header together with dparam data is better
for data consistancy.
TEST=fast calibration pass on Corsola
BUG=b:204226005
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: I22982923dce06c9e770aa4f20f3dcd2f33685d84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Check for situations where a Type C device isn't useful and avoid
creating one for those scenarios.
BUG=b:215199976
TEST=Tested on brya; verified that USBC device is created.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Tested-by: Alyssa Ross <hi@alyssa.is>
Change-Id: I5e1598bd637ec9f50e7bf8dab9e3c757a30b9848
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Compared to Cezanne there are 3 more UARTs controllers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id98767197a21cb1a61f54fc9b256b10a9506c791
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Compared to Cezanne there are 3 more UARTs with DMA controllers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3a3d255bb4976a55623f3a161e791e80f1d01c69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Let's increase this to avoid losing any logs.
BUG=b:213828947
TEST=Boot guybrush and no longer see
*** Pre-CBMEM romstage console overflowed, log truncated!
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3258145e352af3a75893c7cc96f36eb238c99abb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Replace the Renoir/Cezanne PCI IDs with the Sabrina ones that were added
in commit 27b02c2eee (include/device/
pci_ids.h: add PCI IDs for AMD Family 17h Model A0h SoC).
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I427df6f8e8c08fb47ae8513b6cf1085d4294e28f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
To have the new AMD Sabrina SoC code tested, add the AMD Chausie
mainboard as a copy of Majolica. This patch also changes the name from
Majolica to Chausie, selects the Sabrina SoC instead of the Cezanne SoC
and comments out the APCB_SOURCES since those aren't available in the
3rdparty/blobs repository yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic7b18f7a6ae5b8365234dd1227e0b1f7f37279da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Document #55758 Rev. 1.13 says that family 17h models 30h-3Fh and later
use the spi_readmode_f17_mod_30_3f struct element for SPI_MODE_FIELD and
spi_fastspeed_f17_mod_30_3f for SPI_SPEED_FIELD, so also use this for
The AMD Sabrina SoC which is family 17h models A0h-AFh.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I336f9ea4a0defdf34e1af4b6d568cfe46488f75e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The Cezanne SoC code was initially started as a copy of example/min86
which only provides enough code to make the SoC code build. Then the
different parts of the real SoC support was brought in patch by patch
which also helped cleaning up and untangling the code. Since the Cezanne
SoC code is now in a rather good shape and the Sabrina SoC is similar to
the Cezanne SoC from the coreboot side, the new SoC support is started
with a copy of the Cezanne code and all the needed changes will be
applied on top of that. In order for the build not to fail due to
duplicate files, this patch does not only copy the directory, but also
replaces most instances of the Cezanne name with Sabrina. Since the
needed blobs aren't available in the 3rdparty/amd_blobs repository yet,
the Cezanne blobs are used for now so that the build will succeed. As
soon as the proper blobs will be available in that repository, the code
will be switched over to use them.
As suggested by Nico, I added a "TODO: Check if this is still correct"
comment to the beginning of every copied file and all SOC_AMD_COMMON_*
Kconfig option selects which will be removed after re-verifying that
each file and each selected common code block is still correct for the
new SoC.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I978ddbdbfd70863acac17d98732936ec2be8fe3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The AMD Sabrina SoC will be using the FSP driver to call into the
corresponding FSP binary to do its part of for the silicon
initialization, so we need an initial set of FSP headers for the AMD
Sabrina SoC code to build. Since the FSP interface for this SoC won't be
too different from the Cezanne FSP interface, we'll start with a copy of
the Cezanne FSP headers and update/replace them as soon as the proper
FSP headers for Sabrina will be available.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib3bf50598efe60673b81cf99da491866fb5dc121
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This reverts commit 2a8de6dafb.
SeaBIOS 1.15.0 regresses on systems with NVMe devices [1]:
> Greetings! Was this patch set tested on bare metal hardware? I'm
> seeing "GRUB loading: Read Error" when attempting to boot from NVMe on
> various Purism Librem devices (Intel Skylake thru Cometlake hardware).
> Reverting this series resolves the issue.
So, revert back to SeaBIOS 1.14.0.
[1]: https://mail.coreboot.org/hyperkitty/list/seabios@seabios.org/message/SRECAGH4NE3XPDWJ2YI526L5LPSJWENJ/
Change-Id: If2ec738d478f11b203f499eaa28197357de6630d
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61179
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The object pointed to by the struct device * argument is not modified,
therefore it can be made const.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I300d2a59eb0513ddd08d4f1d2a3c6eb829e3f836
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The Lemur Pro, with its mixed memory topology, only has a DIMM at
address 0x52.
Change-Id: Iecea8c70c7fd40943d86f8918f8e3b384538b5c3
Fixes: 4dcee4f21d ("mb/system76/lemp10: Add System76 Lemur Pro 10")
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
When calling get_pcie_rp_pmc_idx(), the following code checked the
return value to see if it was negative or `> CONFIG_MAX_ROOT_PORTS`.
However, the expected return value for CPU PCIe RPs is above
MAX_ROOT_PORTS. Since the static, local function is intended to return
-1 or a valid value, drop the check for `> CONFIG_MAX_ROOT_PORTS`.
Change-Id: I2039273ad246884cd8736a7f0355e621a706a526
Fixes: b6a15a7 ("soc/intel/common/block/pcie/rtd3: Update ACPI Update
ACPI methods for CPU PCIe RPs")
Tested-by: Tim Crawford <tcrawford@system76.com>
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Like the variant function to change DXIO settings, add a similar weak
function to modify the DDI settings.
Currently we follow the old way. Later we will find out a better way
to avoid using weak function.
Change-Id: I9898d717bc3025ea1ddc3b0db41325083324ed57
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
To be shared with different SOCs, move the dramc_param_header struct
as well DRAMC_PARAM_FLAG and DRAMC_PARAM_CONFIG enums to a common
header file dramc_param_common.h.
TEST=fast calibration pass
BUG=b:204226005
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: I087971799803e47e34c30063b2b0bd0cfc5795ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61132
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Building libgfxinit with Debian’s toolchain – latest test with *gnat-11*
11.2.0-13 from Debian sid/unstable – the build fails with the error
below.
E: Invalid reloc type: 10
E: Unable to create rmodule from 'build/cbfs/fallback/ramstage.debug'.
Debian’s toolchain is built without enabling PIE by default.
So, explicitly pass `-fno-pie` to `ADAFLAGS_common` to be independent
from how the toolchain was built.
TEST=*gnat* 11.2.0-13 successfully. builds
purism/librem_cnl/variants/librem_mini with libgfxint.
With the coreboot toolchain `make BUILD_TIMELESS=1` produces the
same `build/coreboot.rom` for `BOARD_PURISM_LIBREM_MINI_V2=y` on
top of commit 50251400d2 (sb/intel/common/firmware: Reword
me_cleaner warning) with and without the change.
Change-Id: I6661937906d95c130c6099f598d61b21e958fd85
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change splits the size of the console transfer region and size of
the bootblock/romstage Pre-RAM console region. This allows having a
larger Pre-RAM console while not impacting the size of the PSP verstage
console.
Instead of directly using the PRE_X86_CBMEM_CONSOLE_SIZE symbol in
`setup_cbmem_console`, I chose to use the offsets provided in the
transfer buffer. It would be nice to eventually do this for all the
fields in the transfer buffer.
BUG=b:213828947
TEST=Boot guybrush and verify verstage logs are no longer truncated
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I8b8cc46600192a7db00f5c1f24c3c8304c4db31d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
When running in verstage before bootblock, the PSP (ARM co-processor) is
running with limited SRAM. It needs to stash the verstage console data
internally until DRAM is brought up. Once DRAM is brought up the data is
stashed in a "transfer buffer" region. In the current design, we are
using the same region for the transfer buffer and the
preram_cbmem_console region. This has the following downsides:
1) The pre-x86 buffer needs to be large enough to hold all the
verstage, bootblock and romstage console logs.
2) On AMD platforms, the PSP verstage is signed. Changing the size of
preram_cbmem_console after the fact will result in a mismatch of the
transfer buffer between verstage and bootblock.
This CL adds a new method that allows SoC specific code to copy the
CBMEM console in the transfer buffer to the active CBMEM console.
BUG=b:213828947
TEST=Boot guybrush and no longer see
*** Pre-CBMEM romstage console overflowed, log truncated!
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idc0ab8090db740e0d1b3d21d8968f26471f2e930
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Subrata Banik