All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c
file already placed under southbridge/.
All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally
identical reset.c file under mainboard/. Move those files under
respective southbridge/.
Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3486
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Confusingly, romstage compiled in different copy of soft_reset()
than ramstage. Use source in reset.c for both.
Change-Id: I2e4b6d1b89c859c7cf5d9e9c8f7748b43d369775
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3487
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The chip component is unconditionally selected for the mainboard
so these uses are superfluous.
Change-Id: I84b053ab47f7b1f68e88d968cf305e24bc95f4da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3485
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
CONFIG_HUDSON_XHCI_ENABLE will control the XHCI flags in the
amd/parmer and asus/f2a85-m mainboards. The XHCI ports on
amd/thatcher are not wired to USB jacks so always disable the flags.
This was tested on amd/parmer using a USB 3.0 thumbdrive.
Change-Id: I596b040fec30882d8d4dee34ab9f866dc1f8896b
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3465
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
To have USB 3.0 support the XHCI controller needs to be enabled
and the xhci.bin firmware needs to be added to CBFS.
Change-Id: I0b641b30b67163b7dc73ee7ae67efe678e11c000
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3464
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Find all the (ramstage) implementations of enter()/exit() functions
for the configuration state, register and call them through the new
struct pnp_mode_ops. As our standard PnP functions are aware of the
pnp_mode_ops, it's not necessary to call enter()/exit() around them
anymore.
Patch generated with the cocci below. It's not perfect. The movement
of the enter()/exit() calls is somehow fragile. So I checked the
remaining calls for sense, and changed some empty lines. Also a
duplicate insertion of pnp_conf_mode_ops had to be removed.
/* Try to find enter and exit functions by their outb() structure and
their usage around calls to our standard pnp functions: */
@ enter_match @
identifier enter;
identifier dev;
type device_t;
@@
void enter(device_t dev)
{
<...
outb(..., dev->path.pnp.port);
...>
}
@ exit_match @
identifier exit;
identifier dev;
type device_t;
@@
void exit(device_t dev)
{
<...
outb(..., dev->path.pnp.port);
...>
}
@ pnp_match @
identifier op;
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
identifier enter_match.enter, exit_match.exit;
type device_t;
identifier dev;
@@
void op(device_t dev)
{
...
enter(dev);
...
pnp_op(dev);
...
exit(dev);
...
}
/* Now add enter/exit to a pnp_mode_ops structure: */
@ depends on pnp_match @
identifier enter_match.enter;
identifier exit_match.exit;
identifier ops;
@@
+static const struct pnp_mode_ops pnp_conf_mode_ops = {
+ .enter_conf_mode = enter,
+ .exit_conf_mode = exit,
+};
+
struct device_operations ops = {
...,
+ .ops_pnp_mode = &pnp_conf_mode_ops,
};
/* Match against the new structure as we change the code and the above
matches might not work anymore: */
@ mode_match @
identifier enter, exit, ops;
@@
struct pnp_mode_ops ops = {
.enter_conf_mode = enter,
.exit_conf_mode = exit,
};
/* Replace enter()/enter() calls with new standard calls (e.g.
pnp_enter_conf_mode()): */
@@
identifier mode_match.enter;
expression e;
@@
-enter(e)
+pnp_enter_conf_mode(e)
@@
identifier mode_match.exit;
expression e;
@@
-exit(e)
+pnp_exit_conf_mode(e)
/* If there are calls to standard PnP functions, (re)move the
enter()/exit() calls around them: */
@@
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
expression e;
@@
-pnp_enter_conf_mode(e);
pnp_op(e);
+pnp_enter_conf_mode(e);
...
pnp_exit_conf_mode(e);
@@
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
expression e;
@@
pnp_enter_conf_mode(e);
...
+pnp_exit_conf_mode(e);
pnp_op(e);
-pnp_exit_conf_mode(e);
@@
expression e;
@@
-pnp_enter_conf_mode(e);
-pnp_exit_conf_mode(e);
Change-Id: I5c04b0c6a8f01a30bc25fe195797c02e75b6c276
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3482
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Many super i/o chips only answer to PnP requests if they are in a
configuration state (sometimes also called ext func mode). To cope with
that, the code of many chips implements its own version of our default
PnP functions like pnp_set_resource(), pnp_enable_resource() etc.
To avoid this code duplication, this patch extends our PnP device
interface with optional functions to enter and exit configuration mode.
Change-Id: I9b7662a0db70ede93276764fa15020f251eb46bd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3481
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current default implementation of pnp_enable() only disables devices
- if set so in the devicetree - but does not enable them. Enablement takes
place in pnp_enable_resources(). Yet, many PnP chips implement their own
version of pnp_enable() which also enables devices if set in the devicetree.
It's arguable, if enabling those devices makes sense, before they get
resources assigned. Maybe we can't write the resource registers if not,
who knows? The least we can do is providing a common implementation for
this behavior, and get rid of some code duplication.
Used the following cocci:
@@
expression e;
@@
+pnp_alt_enable(e);
-pnp_set_logical_device(e);
(
-pnp_set_enable(e, !!e->enabled);
|
-(e->enabled) ? pnp_set_enable(e, 1) : pnp_set_enable(e, 0);
|
-if (e->enabled) { pnp_set_enable(e, 1); }
-else { pnp_set_enable(e, 0); }
)
Change-Id: I8d695e8fcd3cf8b847b1aa99326b51a554700bc4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3480
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
They were hard-coded to be copied from 3rdparty/ which isn't always
the right choice.
Since the defaults stay the same, this should be compatible.
Change-Id: If2173bef86ad1fcf2335e13472ea8ca41eb41f3d
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3453
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Most PnP drivers align the initialization of their `device_operations`
with spaces. Unify this, so next autogenerated patches always match the
alignment.
Change-Id: I3f6baef6c8bb294c136354754125ea88c07a61a1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3479
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for the new q35 chipset emulation
added in qemu 1.4.
Change-Id: Iabfaa1310dc7b54c9d224635addebdfafe1fbfaf
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3430
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
So the pci allocation code knows where memory is and doesn't
try map pci devices there. We also don't have to check for
overlaps between pci hole and memory then.
Change-Id: I5eaea0e4d21210719685860fa1f16ca7b2137cde
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3491
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
An uninitialized RAM value was used to select an MSR because a $ was forgotten
in front of `CPU_DM_CONFIG0`. It should be the constant value 0x1800, corresponding
to CPU_DM_CONFIG0 MSR defined in `src/include/cpu/amd/lxdef.h`.
Change-Id: Id53ca98b06cc4a9b55916fd8db23904f98008d45
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://review.coreboot.org/3478
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The original lines had contradicting comment and code.
This change follows the code and sets MASTER bit too.
Change-Id: Id2886bfc107612530f0e9747e5d49a9740fb8532
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3466
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Prepare tree for adding q35 support:
Move emulation/qemu-x86 to emulation/qemu-i440fx.
Rename some stuff to include 'i440fx'.
Change-Id: Ib8c58175c5734cfcda1b22404ef52c09d38f0462
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3429
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
With this patch, output on usbdebug also includes the section of
MTRR setups for every CPU. This makes usbdebug output almost identical
with that of serial port and CBMEM console.
Tested with model_206ax. Also tested previously on model_f2x which does
not have these disable/enable calls in model_f2x_init() without detected issues.
Change-Id: Idfd0e93439907b17255633658195d698feab3895
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3423
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
This patch provides the correct SD controller timings for
the Family16 device. It also will remove the SD controller
from PCI space when device 0:14.7 is set to off in devicetree.
This was tested on a AMD Parmer board and a AMD G-series SOC
reference board. The settings were found in the AMD
Hudson2 RRG and family16 BKGD.
Change-Id: I6d7e7997ddc39802ab75dc8a211ed29f028c0471
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3348
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In function OemAgesaSaveMtrr of 'src/cpu/amd/agesa/s3_resume.c',
there are many code like this:
msr_data = rdmsr(0x258);
flash->write(flash, nvram_pos, 4, &msr_data.lo);
nvram_pos += 4;
flash->write(flash, nvram_pos, 4, &msr_data.hi);
nvram_pos += 4;
Add a function write_mtrr to do this.
Change-Id: Id6464e637db1758b07ac2d79d3be1375a8d49651
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3410
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This issue can be reproduced in Linux by the following steps:
1) use pm-suspend to suspend.
2) use USB keyboard to wake up.
3) use pm-suspend to suspend. FAIL To SUSPEND.
The cause of this issue is:
USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event,
but this bit is not clear after wake up. So OS thinks there is a
wake up signal and wake up immediately.
In this patch, I add AcpiGpe0Blk using MMIO access and write 1
on bit 11. Write 1 to clear as spec says.
I have tested on Thatcher
The same change was done for AMD Parmer in commit »AMD Parmer:
fix issue 'S3 fails to suspend after wake up from USB keyboard'
(03901124) [1].
[1] http://review.coreboot.org/#/c/3347/
(Change-Id: Iec3078bf29de99683e7cd3ef4e178fbeb4dc09c1)
Change-Id: Iaef39237497ef896d0f186e8f5522222c0ce6cb7
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3374
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Until ME boots (which takes seconds on X201) the reported temperature
is 128 °C which triggers Linux overheat alarm which shuts down.
Pretend temperature is 40°C until ME boots.
Change-Id: Ia49fa03c6eb27f539a23711f2c8ebfde72b1dc18
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3404
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On X201 to enable EHCI debug you need to go through EC if USB power is
disabled so we need to inclue ec.c.
Change-Id: I8f8b7de639ecaebceaa53cd338136befaeec8214
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3405
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable UMTS on Lenovo X60 and X201.
Enable radios if no options are available.
Enable dock on Lenovo X201.
Based on my X201 branch.
Change-Id: I6e8d3bbd6a6b1a8e59473dd5cc8125a1583d75df
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/3377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a struct for referencing UART registers. The layout is quite
strange on this chip, as the entire register space can take on three
different meanings depending on the line control settings (in the LCR
register) And to make things more confusing, some offsets reference
different registers depending on if a read or a write operation is
used.
Change-Id: Ie62af9c0e0edafd01b81686a0fe5c5c1d4fa06c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3319
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This ancient board with Intel e7505 invalidates cache while it does HW
scrubbing for ECC in romstage. This breaks usbdebug console and prevents
system from booting.
If both EARLY_CONSOLE and USBDEBUG are selected, skip ECC scrubbing under
these rare conditions to boot system.
Change-Id: I6cb43bf69af54119f4a582dcaf498dd941d4c62d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3385
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In case with EARLY_CONSOLE, this printk is called before any other
console is configured to transmit data. This outputs garbage on
CONSOLE_SERIAL as baudrate is not yet programmed.
For case without EARLY_CONSOLE, the order in which different console
drivers initialize is obscure. Might sometimes work properly.
Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3384
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Add comment how one can debug the usbdebug hardware init.
Do not send printk's to usbdebug console when one is debugging
the usbdebug console initialisation itself.
Change-Id: I21a285cb31cf64e853bc626f8b6a617bc5a8be19
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3382
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Setting IRQ delivery to FSB got lost in the rebase process
for commit e6143531.
I captured following error on dmesg and this patch fixes it for
i82801dx.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 2) ...
....... failed.
...trying to set up timer as Virtual Wire IRQ...
..... works.
Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3371
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to
GPIO0.
Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3436
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the
file `usb_debug.c` is added twice to the build.
This was introduced in
commit 4063ede3fb
Author: Ronald G. Minnich <rminnich@google.com>
Date: Mon Feb 4 20:31:51 2013 -0800
bd82x6x: Fix compiling with USB debug port support
Reviewed-on: http://review.coreboot.org/2784
but was unneeded because it had been already added in
the following commit.
commit 4141993536
Author: Sven Schnelle <svens@stackframe.org>
Date: Sat Jul 28 08:52:44 2012 +0200
bd82x6x: Fix CONFIG_USBDEBUG
Reviewed-on: http://review.coreboot.org/1376
Therefore basically revert that hunk.
There is no policy on how to order these additions, so leave
it to a possible separate commit, unifying this.
Kyösti Mälkki suspects that these additions were meant for
the Intel Lynx Point [1].
[1] http://review.coreboot.org/#/c/3424/
Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3425
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix obvious mistake in cycle that displays GPI status
I hope i found all duplicates of it.
Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/3435
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current method will treat hex values as 0 and would calculate the wrong
size. This change switches back to an earlier method which used shell syntax
to add the offset and size.
Change-Id: I9fb2d9b323f113cc56a5ad2e38b47d2d22084f08
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3432
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is loosely based on Christoph Grenz' ACPI code for the W83627HF
and makes use of the PnP super i/o ACPI framework.
Change-Id: I5e1cd09b83c0041f440562d2a1b73e4560589cb7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3288
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I'm trying to make writing ACPI code for super i/o devices more
comfortable.
pnp.asl hosts some general cpp macros.
The other four files are to be included in dsdt trees. They are
controlled by cpp macros which should be defined/undefined before
inclusion.
Work was inspired by Christoph Grenz' ACPI code for the W83627HF.
Change-Id: Idb55332ba9bc788c98964d30a450e0d734cf28ec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3286
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The bootblock and ROM stages are the only ones that are really required to be
loaded in the quite limited on chip RAM during startup. Rather than load the
whole image which requires everything to be small, load just the bootblock and
the ROM stage, allowing the rest of the image to be arbitrarily large. Loading
a minimal amount of stuff should also improve boot performance a little bit.
Change-Id: I2fede63b8d3d8f0d880e4a692ae423021f8232b6
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3421
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that the ROM size is decoupled from the size of the on chip RAM,
it's size is now only constrained by the size of the medium it's loaded
from and the memory it's being loaded into, probably GBs in both cases.
Making it 4MB is a reasonable compromise between giving the payload lots
of breathing room and wasting space on the source medium which won't be
used.
Change-Id: I80932e0d4ce2dad02c3879345382e7d6ba44503a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3422
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Until we get serial working, this is a good way to show that coreboot is
running. It can be removed once we have better methods.
Change-Id: I62d25e52aa88a97aba4c959538d680b67a0bbbb2
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EPIA-M850 can now boot linux. For a list of issues, see:
http://www.coreboot.org/VIA_EPIA-M850
That's all folks.
Change-Id: I7624944dbc05fbf3019897a116954d71dfda0031
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1228
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the minimal code needed to get past ramstage, load SeaBIOS, jump
to GRUB2, and boot linux (or load memtest). See individual source files for
the status of each individual component.
Change-Id: Ib7d5d7593c945f18af2c2fc5e0ae689ba66131a2
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3419
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The VX900 can be connected to either DDR2 or DDR3. On my board, it is
DDR3, hence why there is no and will be no DDR2 code from my side.
This is the raminit for DDR3 dimms for the VX900. I like the term
"raminit" better than "memory training". This is a device, not a dog.
What works and what doesn't is documented in the code. It does not
make sense to hide that information in a commit message.
Change-Id: Ib2ebc10e6d4d22d0a937fe9e895c17ce79153c88
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3417
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In some cases, we want a ram_check that does not die and does not
clobber the terminal with useless output that slows us down a lot.
Usage examples include Checking if the RAM is up at the start of
raminit, or checking if each rank is accessible as it is being
initialized.
As with all other ram_checks, this is more of a "Is my DRAM properly
configured?" test, which is exactly what we want for something to use
during memory initialization.
Change-Id: I95d8d9a2ce1e29c74ef97b90aba0773f88ae832c
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3416
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for VX900 early initialization up until, but not including
raminit. Add the basic infrastructure, add a romstrap table, and
functionality to configure the CPU bus and SMBus.
This code is necessary and sufficient to prepare us for raminit.
Change-Id: Icc9c41e4927b589f17416836f87a6a5843b24aa7
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/3372
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Kyösti Mälkki