Move PSP_SHAREDMEM_DRAM_END after _etransfer_buffer to ensure that the
transfer buffer actually lives within the 32KiB that is supported to be
transferred. Resulting symbol address change in bootblock.debug file
summarized below.
BEFORE:
02011000 T _psp_sharedmem_dram
02011000 T _transfer_buffer
02011000 T _transfer_info
02011040 T _etransfer_info
02011040 T _vboot2_work
02014040 T _evboot2_work
02019000 T _epsp_sharedmem_dram
02019000 T _preram_cbmem_console
0201a600 T _epreram_cbmem_console
0201a600 T _timestamp
0201a800 T _etimestamp
0201a800 T _fmap_cache
0201ac52 T _efmap_cache
0201ac52 T _etransfer_buffer
AFTER:
02011000 T _psp_sharedmem_dram
02011000 T _transfer_buffer
02011000 T _transfer_info
02011040 T _etransfer_info
02011040 T _vboot2_work
02014040 T _evboot2_work
02014040 T _preram_cbmem_console
02015640 T _epreram_cbmem_console
02015640 T _timestamp
02015840 T _etimestamp
02015840 T _fmap_cache
02015c92 T _efmap_cache
02015c92 T _etransfer_buffer
02019000 T _epsp_sharedmem_dram
BUG=b:167243965
BRANCH=None
TEST=checked 'cbmem -1' for FMAP error after ec reboot
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I9b482aced5deb40bd87d19d9c42585d8a6db5fc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45045
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some Trogdor variants power their USB hub from a PMIC LDO that is
already enabled by QcLib, and some have a discrete LDO that is
controlled by GPIO_84. For the latter, let's make sure we assert that
GPIO on boot.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9d206cd7154ded3bf179e68c2b1421d0a8ee89f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
We're moving a lot of pins around on Trogdor again. For firmware this
only affects the RAM and SKU strapping ID pins. Since there are quite a
few of the old devices in circulation this time and some people seem to
care about mosys RAM information working, let's actually check the board
revision and support both cases this time.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7728d8ea4b7f6e7ff6721ade90f975f6efd5ddd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Set tcc offset to 5 degree celsius
2. Apply the DPTF parameters receive from the thermal team.
3. Change PL2 min value from 25W to 15W.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I68fdefe99cf36a39797c29ad84d08321bb8175f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This reverts commit 2ad859988b.
Reason for revert: broke the build
Change-Id: I7e7d917c2e8b698d5c7c3ce0b6d34e80696185f3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44993
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add new SPD file, "samsung_dimm_K4E8E324ED-EGCG.spd.hex".
2. Add SPD support in Rammus memory table, as follows:
SPD_SOURCES += samsung_dimm_K4E8E324ED-EGCG # 0b0110
SPD_SOURCES += samsung_dimm_K4E6E304ED-EGCG # 0b0111
BUG=b:166576463
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I82386507c4e996e0a59c26ce50de3bced45b1196
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44854
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:153888802
TEST=Able to list correct eSPI frequency as per TGL SPI flash guide
Without this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 50MHz
Write/Erase Clock Frequency: 50MHz
Fast Read Clock Frequency: 50MHz
Fast Read Support: supported
Read Clock Frequency: 20MHz
With this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 50MHz
Write/Erase Clock Frequency: 50MHz
Fast Read Clock Frequency: 50MHz
Fast Read Support: supported
Read eSPI/EC Bus Frequency: 60MHz
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I20840e6f931d7c1fabea0b6892e3bd19ead81168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BUG=b:153888802
TEST=Able to list correct SPI frequency as per TGL SPI flash guide
Without this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 33MHz
Write/Erase Clock Frequency: 33MHz
Fast Read Clock Frequency: 33MHz
Fast Read Support: supported
Read Clock Frequency: 20MHz
With this CL :
Found Component Section
FLCOMP 0x093030f6
Dual Output Fast Read Support: not supported
Read ID/Read Status Clock Frequency: 50MHz
Write/Erase Clock Frequency: 50MHz
Fast Read Clock Frequency: 50MHz
Fast Read Support: supported
Read Clock Frequency: 20MHz
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Id0a0a0cbd948ef8334cf522c09e881b464e87f0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Consider IBEX_PEAK onwards all chipsets are belong to PCH family.
BUG=b:153888802
TEST=Able to print correct PCH revision on Hatch Platform.
> ifdtool -d coreboot.rom
Without this CL :
ICH Revision: 300 series Cannon Point/ 400 series Ice Point
With this CL :
PCH Revision: 300 series Cannon Point/ 400 series Ice Point
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Ifd40dddc9179f347c0ea75149ec08089a829fdb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
BOOTBLOCK_CONSOLE is already set to yes in console/Kconfig file.
Change-Id: I2a4ee517795bc7b378afc5eae92e2799ad36111b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
1. Apply the DPTF parameters receive from the thermal team.
2. Change PL2 min value from 25W to 15W.
3. Change PL2 max value from 64W to 51W.
BUG=b:166696500
BRANCH=puff
TEST=build and verify by thermal team
Change-Id: I53a4e8809369883c3ba77744fdc05fb510408209
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44903
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch converts the current DPTF policies from static ASL files into
the new SSDT-based DPTF implementation. All settings are intended to be
copied exactly.
BUG=b:158986928
BRANCH=puff
TEST=duffy boots and dumped SSDT table for quick check.
Change-Id: I45987f44ec381917173f8d2a878edb50da454b4b
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The bus master bit is set at many places in coreboot's code, but the
reason for that is not quite clear. We examined not setting the
bus master bit whereever possible and tried booting without it,
which worked fine for internal PCI devices but not for PCIe. As a PCIe
device we used a Samsung M.2 NVMe SSD.
For security reasons, we would like to disable bus mastering where
possible. Depending on the device, bus mastering might get enabled
by the operating system (e.g. for iGPU) and it might be required for
some devices to work properly. However, the idea is to leave it disabled
and configure the IOMMU first before enabling it.
To have some sort of "backwards compatibility", add a method which
configures bus mastering based on an additional config option. Since
CB:42460 makes usage of this treewide, enable it by default to keep the
current behaviour for now.
Tested with Siemens/Chili, a Coffee Lake based platform.
Change-Id: I876c48ea3fb4f9cf7b6a5c2dcaeda07ea36cbed3
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42459
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO_144 is REPORT_EN pin for the touchscreen controller where 1 means
enable operation and 0 means stop operation. Override tree exposes
this pin as stop GPIO. Thus, it needs to be configured as active low
i.e. 0 = active (stop), 1 = inactive (enable report).
Change-Id: I349123655260349b78d2f75f846da0ce1dc966fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
v3.6+ of reference schematics have moved to using active low polarity
for touchscreen GPIO. This change sets the default polarity in
override tree accordingly to active low. To support boards from older
builds, variant_touchscreen_update() already updates the polarity to
active high.
BUG=b:161937506
Change-Id: I370bdb27ea5d0601612d13b515113a6048018964
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Clone entirely from Jasperlake
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Rename structure based on Jasperlake with Elkhartlake
4. Clean up upd override in fsp_params.c, will be added later
5. Temporarily remove _weak attributes in fsp_param & romstage.c
6. Add required headers into include/soc/ from jasperlake directory
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: If2bbe0b8a12bb78b3650f9d0a60f002f7eacb513
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Clone entirely from Jasperlake
This patch is based on TGL_upstream series patches:
https://review.coreboot.org/c/coreboot/+/36550
List of changes on top off initial jasperlake clone
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Rename structure based on Jasperlake with Elkhartlake
6. Add required headers into include/soc/ from JSL directory
Elkhart Lake specific changes will follow in subsequent patches.
1. soc/intel/elkhartlake: Update Kconfig
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I9f91c1efa81a358b1f59e032e209e07b62d54613
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Able to uniquely identify the chipset without specifying the platform
specific quirks (adl/cnl/icl/jsl/tgl etc.).
BUG=b:153888802
TEST=Able to dump FD contains correctly without specifying platform
quirks on Hatch Platform.
> ifdtool -d coreboot.rom
Without this CL :
ICH Revision: 100 series Sunrise Point
With this CL :
ICH Revision: 300 series Cannon Point/ 400 series Ice Point
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I83763adb721e069343b19a10e503975ffa6abb24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44815
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The BT instruction stores its result in CF and not ZF so use the
correct jump instruction.
This fixes a hang in postcar on CPUs lacking support for this
instruction. This concerns older pre-SSE2 hardware.
Change-Id: I704e3c579150fb9b9a292ef0e83050e7bf7cb078
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
- Use a new variable to store the list of warning types;
- print this list when building an image.
TEST = build image on Kontron mAL-10 COMe module:
IASL 3150 2158 3133 warning types were ignored!
IASL build/dsdt.aml disassembled correctly.
Change-Id: I46f761612254b400563f8567be9bd61601f23467
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Checked with the schematics that all PCIe clocks have a corresponding
clock enable pin.
BUG=b:149970243
BRANCH=zork
Change-Id: If96cdf95e213682217e46a98fc69c5c2ef4a148d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44892
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make the general purpose PCIe clock outputs configurable to be either
permanently enabled, permanently disabled or dynamically enabled via
their corresponding external #CLK_REQx pins in the board's devicetree.
BUG=b:149970243
BRANCH=zork
Change-Id: I3f5760c0b869e8a9416ba9b57d182a88a2eb5e44
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The _SHIFT postfix is a bit clearer than the _SHL one and more in line
with the names used for this kind of defines in coreboot. The
documentation on that register is currently wrong and will hopefully be
fixed in the future; the defines should now match the hardware.
BUG=b:149970243
BRANCH=zork
Change-Id: I977f107d466521484ca13fa1f4dd86a50c8150d7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The code using the macro was found not working after finally enabling
the HDA PCI device on the hermes board.
Fix a typo to generate the correct verbs.
Tested on prodrive/hermes.
Change-Id: I953c2e9fbebc1f02bdf71ce868a95f578300c3a1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44900
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Josie Nordrum